I made a bone head mistake and crunched the steel brake line between the rear axle and the passenger side sway bar mount. Truck is a 2003 F-250 with a 7.3. I would like to go to the auto parts store, get bulk steel brake line and bend it myself. But, I don't know what size the line is or what size the fittings are. Whatare the sizes???
View 3 Repliesso while replacing the rear brake lines in my 2001 F-250. / 5.4, the flex line that drops from the frame bolts to the axle through the axle breather threaded vent line. The friggin thing crumbled on me and now I can't find a replacement for it. Where I can get it or what it's actual name / part number is so I can call the Ford dealer and hope it's not obsoleted?
View 3 RepliesHad the rear passeneger side brake line burst today in rush hour traffic ..wasn't much fun. Is it a easy to do it yourself deal ...it is a 2003 f250 v10 triton .
View 1 RepliesI noticed yesterday that my tire on the driver's side has rubbed a flat spot on the rubber brake hose. I bent the metal tubing so that it doesn't rub any more, but should this be of great concern? Obviously I'd hate for it to rupture, but it looks as though it's not too bad.
View 1 RepliesHere's my problem while replacing brake pads i found that my axle has leaked fluid on the pss,side rear rotor and all over .. I been looking for any info on repairing it myself . I found Everything for every other truck just not for this truck.
It's 2003 F-250 w/5.4L all Stock rear axle has 12 bolts and gears are 7.73 ... I believe its a Dana 60. No tags or markings on the Axle to go by..
I live in the Freak-en woods here so i like to order all the right parts once and do over the weekend .. its my only ride so once apart im stuck here.... I did check the Vent Tube its fine..
Just got done rotating my tires on my 16 F250 ccsb 4x4 and I used jack stands on my rear axle while I used the jack on the front axle. When I brought the truck down off the jack stands (first time using jack stands on this truck) I saw that they left little marks/divits on the rear axle. I had them between the wheel and the shock support and I can feel with my finger where the jack stand was supporting the truck. It doesn't seem anything major but I can surely point out to you exactly where the axle and the jack stand met. I'm sure this is a non issue but just wanted to check in here to make sure...
No trailer attached (of course!) And nothing in the bed with a full tank of gas...so basically just the weight of the truck...
1999 F150 has rusted and leaking steel brake lines. I need to replace all of them but do not know if you have to fabricate them or can you buy the complete kit. I am also confused with the flared end. Have not worked with that type of flare. If they need to be purchased where is the best place to buy them ?
View 9 RepliesOn my '97 F250 the rear brake line going to the rear right wheel has a rusted hole. It measures 50" total. Instead of bending a new metal line. I see they have a "poly armor" line that can be bent by hand( no tools needed). I see Autozone has them.
View 14 RepliesSo I'm away from home on vacation also away from my tools. Any ways my front drivers side line busted almost causing me to crash earlier today in my 2006 F250 6.0 diesel 4x4. So basically my question is: what tools are needed to do this job? I've already picked up the part now tomorrow morning I will be changing the part...
View 2 RepliesMy truck is a 2008 F250 6.4 Powerstroke 4x4 King Ranch, CrewCab, Shortbed.
I don't know which rear axle ratio it has - maybe someone can help me. the tires mounted are 275/60R17 and in fifth gear (TC locked) the engine has 2000rpm @ 70mph. I think it is a bit to much so I want to install a kit with and lower ratio. I pull trailers just sometimes and here in germany these only have 3,5tons max weight. So I think I don't need this power at 70mph. 1750rpm would be enough. How do I have to modify the front axle ratio if I get a lower-ratio-rear-axle?
I want to lower the fuel consumption. After some modifications, the truck needs round about 12-13L/100km (18-20mpg) and I think it is possible to lower this as bit.
I have a 2000 dually and the brake line that runs the frame rail finally rusted through. It runs on the same side as the fuel tank. Is it easier to leave the old one in and run a new one along side it? I sure hate to think that I'll have to drop the tank for this.
View 7 RepliesReplacing the knuckle/axle seal due to my hub not holding a vacuum. I finally got the seal off the axle after several minutes of beating, but it finally came off. During the beating the metal shield that was in back of the seal took a beating as well and can not be reused. Is it really needed?
In this thread the pictures show that the shield was not installed after the seal was replaced. The shield does serve a purpose to keep crap out of the seal though.
2010 F250, what size tube do I need to fit on the brake bleeder screw? The tubes I have are all too big and the size marks are no longer legible.
View 4 RepliesHow does it come off. I wasn't able to turn the axle vent without turning the block on axle for the brake lines.
I would like to remove the brake system from my current axle without breaking any lines open, then putting a new axle in and put the brake system on the truck to the new rear axle.
I am replacing the rear steel brake lines and I have a bit of a mystery...when the lines come off the wheels, I see them going over the pineapple and it LOOKS like it's just coming down the other side into the other wheel. That should be impossible, right? How would it go about getting brake fluid into the system?
I can't see on top of the pineapple, so I don't exactly know whats going on up there. I don't see any hydraulic hose coming from the top of the pineapple. I'm currently clueless as to how the rear brake lines fit together.
1999 F250 CCSB Lariat 5.4, 2 wheel drive. I plan to replace the Driveshaft Center Bearing in the next few days. What size is the Nut that I have to remove to remove the yoke next to it so I can press the bearing off?
View 4 RepliesWhat is the size of the bolts on the rear axle that hold the shock absorber? I believe its an M12 x70 mm long??
View 7 RepliesI have a 1999 F-250 super duty 7.3 4x4 and the rear drivers side axle seal is leaking. My question is how do I remove the axle shaft? my last truck a f150 had c clips in the diff that released the axle shaft but I did not see those on this truck. How to remove the axle shaft?
View 8 RepliesLove my '11 f250 SD 4WD CC SB. 6.2 with 3.73 e-locker. I've got 5 Star tunes in it, and the truck is a joy to drive empty, and tows my current 7k camper fine, though on steep inclines I wish I had the 4:30 gears.
Well, we just bought a bigger trailer, dry weight is an addtl 2400+ at 9400, so I'll need to do something.
I don't want a different truck, don't want (another trouble-prone) diesel. I think with 4:30s and the tune, I should be fine towing that trailer (with gear and passengers, probably 11-11.5k loaded). Not doing mountains here, just Michigan hills.
What's the best way to "do" a gear swap? I know if I buy a set of gears and a shop screws Em up, it's gonna whine/hum and still cost 2k to do (truck is 4wd)
I'm up in the boonies and finding a shop to swap the gears will be a problem. Getting Em done right will be even MORE trouble.
Can I just find 4:30 axles ans have them swapped (anything in t-case or sensors need to be touched?). I don't care if I lose the e-locker, I never use it.
What size the pitman arm nut is? And where to get one? I am lifting my truck soon and I'm going to double nut that baby on there. I know they're prone to loosening. I just wanted to have all the parts before I started.
View 4 RepliesI have a 1995 Ford f250 Powerstroke and i do not have turn signals, rear running lights, brake lights or reverse lights. i checked the fuses and they seem to be good but i dont want to tear everything out to check the harness if it could be a bad ground. any insight?
View 1 Replies