Ford Super Duty (1999-2016) :: 2002 F250 - No Start / Would Not Crank Even When Jumped
Jan 5, 2017
2002 F250 V10....
Ambient temp is 4-9 degrees
Step-son borrowed truck. I started it at 9 in the morn and moved it to a different parking spot on street. No problem starting.
Step-son came at 11 and took truck. It started no problem.
He drove it to work. At 5 p.m. would crank, but not start. A jump got it running.
On charger all night. Would not crank this morn. Would not crank even when jumped.
Are we looking at a bad battery or something else?
View 9 Replies
Advertisement
Let me start out by saying that I have exhausted every option that I have read on every thread that I could find on the internet regarding my son's 2002 7.3L not starting. What I have is no 12v power to the starter solenoid at the starter when I crank the key. What we have done so far, had the starter and both batteries tested, all good. Swapped out the starter motor fuse and the starter relay. Tried a new ignition switch and a new trans position sensor. Found major corrosion in the fusible link junction box on the drivers inner fender so we cut out the fusible links and put in a temporary jumper wire, still no crank. I have power to the dash, power on the power cable at the starter. I can jump the terminals on the starter and the starter engages. I found the shifter linkage bolts loose under the dash and tightened them up also. We have been struggling with this for 3 days, out in the lovely Michigan weather, since it couldn't have died in his parking spot in our heated shop, and I am completely frustrated. Are we overlooking something glaringly obvious?
View 11 Replies
On occasion, the last 2 weeks, my truck doesn't like to start, sometimes it will start to crank for one second and then quit. i've tried moving my gear shift through the drive selection range (park, neutral, reverse and drive). i just replaced the starter relay on the fender well because i can always start the truck by jumping across the terminals... no joy. So now ( i think) my issue is between the key switch and the starter relay. i replaced the neutral safety switch about 18 months ago.
99 F250 V10 short bed, 123,000 miles ....
View 1 Replies
I have been trouble shooting a no crank no start issue for a couple years now. Been back to the dealer several times to no avail. Very long story, with all due respect, don't suggest that I go back to the dealer on this. Not happening. Every once in a while the truck would strand me with no crank no start. It would read trailer brake module fault. Sometimes the security light would flash and the alarm would sound. Recently, I have had it on IDS and noticed that while it was doing this, IDS had no communication to the ECU.
I checked IDS with my other truck and it had good communication with that ECU so I know the computer/IDS works. Pulled battery cables and checked all the fuses... checked ok. Went back in the truck tried it, still no crank. Left key on, popped hood to listen for fuel pump... nothing. Went to pop cover off the fuse block and as soon as I touched it the fuel pump started whining. Went back in the truck and it started. Plugged IDS back in and had good communication and read ECU. I googled around for a part number but came up empty.
View 3 Replies
I have a ford f250 super duty and it wont start I have checked obvious reasons and I think it might be a crank shaft sensor. Just curious, is there two of them one for right bank and left bank or just one on drivers side?
View 2 Replies
I have a 2004 Ford F-250 with the 6.0 egr has been deleted and so on. Truck has been very trustworthy until now... It all started last week. I would get in and it would fire right up, drive 15 miles to work all is still good. Time to go home try to start and it would act like the batteries were weak with a weak crank until it finally takes off and starts. This intermittent situation has been happening but I just assumed that the batteries were going bad. I drove to work this morning truck fired right up and now that it is time to go home the truck only has a weak crank and wont fire up. I tested the batteries and they were low on cranking amps.
Replaced them with two new batteries. The issue still exists and didn't change. After reading through threads I found that it could be the FICM I checked it out as was shown through the other threads. With the key on only it was reading 51 vdc with someone trying to start the truck it was reading 48-50 vdc... Yes the truck does have fuel in it and yes the oil is good to. It seems that there is something electrical going on for sure due to the way it has been an intermittent problem for a week or so. I am an aircraft mechanic by trade but can fix anything if I know where to start.
View 5 Replies
My 92 f250 5.8l 5 speed, out of no where when I try to start it I get absolutely nothing, when I put the key in the on position and short the solenoid it starts up that's how I've been starting it? When I try to start it regularly it's almost as if trying to start it without pressing the clutch it literally does nothing.
View 1 Replies
I have 1999 f250 powerstroke, batteries are fully charged but when you put key in ignition and turn you get nothing. No dash lights, no crank, nothing. I cleaned the battery terminals on both batteries, checked all the fuses under the dash and the hood.
View 9 Replies
The factory remote start is not working on my 2009 F 250. The red light is lit when I push the button, the doors lock and you can hear something engage in the engine but it does not crank it. If I keep holding the button the alarm starts to go off. When I walk up to truck the radio is on and I need to hit the remote start button to shut everything down before manually staring.
View 4 Replies
I recently caught up on some maintenance with my truck, changed the turbo pedestal seals, replaced both batteries, brakes, e-brake cable etc and installed new 10k hid headlights. its a single cab 250 with a 7.3 and zf6 4x4 with 133k. a couple days ago I turned on the headlights and the truck died, restarted no problem and would die the next 5 times I tried to turn them on, then it worked fine. yesterday I got in my truck to leave for work and got no wait to start light, no glow plug chatter, no fuel pump running. turns over just fine but no fire.
I got a ride to work and tried it when I got home, fired right up. I pulled the pCM, checked it out, no weird smells and my TS chip wasn't corroded or anything like that, worked fine. drove to 711 to get a 6 pack and it did the headlight thing again. I removed the HIDs because this all started after I installed them and reinstalled my silvanias and it didn't die when I turned them on. this morning went to leave for work, same no start condition. I disconnected both batteries for 30 seconds to reset anything and same problem. I was about ready to light it on fire this morning.
View 1 Replies
2001 F250 5.4 ... I'm losing my mind chasing a Gremlin. I've been having mostly intermittent starting issues with my truck. I've had the truck for a little over a year, after someone totaled my previous one.
It occasionally wouldn't start on the first attempt, but it got really bad in the last couple weeks.
I first thought it was a faulty inertia switch or wiring in that vicinity, as at one point after manually tripping and resetting the cutoff switch it would start, UNTIL I put the trim panel back. At this point I think that may have been a coincidence.
I eventually probed the switch and it tests as it should electrically.
I put in a new fuel filter and things were fine for several days, but it acted up again. That time was last Saturday. Got it to start and all was good until tonight. Now it won't go, and I've tried so many times that I can see the battery power is dropping.
Last Saturday I pulled the relays from behind the radio and cleaned 'em up real nice. Also, just to check another variable I swapped the two that matched.
I'm about ready to change the fuel pump, but I've heard so many people say they did that but the problem was something else. Not only will it costs hundreds of dollars, its cold out and we'll have to drop the tank in the driveway.
In addition to the relay, inertia switch and fuse, I have found some mention of faulty fuel pressure regulators causing issues. I'll pry the vacuum line off in the morning to see if I can detect fuel residue on the vacuum side. (There is some noticeable corrosion on the fuel rail in that area).
I REALLY want to make sure I rule everything else out before spending hours under the truck in freezing weather dropping the tank and changing the sending unit out.
On key-on there is a noise from the gas tank, but someone else listening described it as a click but no whirring.
I do hear the relay clicking behind the radio. (Also, I pulled them again tonight and put a meter to them. With 12V on the primary side, they click and the other side shows continuity on diode check, and about .2 Ohm on resistance mode.)
I went through a lot of trouble to get my spare out looking for the fuel control module before finding out my truck is about 3 years too old to have one too. What else to check?
View 3 Replies
Been driving my 2001 f250 7.3 4x4 with no problems then started noticing it lacking power so I changed fuel filter and air filter. After a week goes by I was at work and I was leaving to come home so I started truck to let warm up and it cranked longer than normal but started. Let run about 10 minutes idle nicely when I punched it it bogged down and had no power never died. I idled over into parking lot and power came so I took off again loss all power again, still never died. Got it right back to my work sat there a bit and tried again this time I took it easy and was able to get my truck home 30 so miles.
When I got home I ran codes p1211 came up for the icp sensor I changed it did not change anything still had same problem. This was a Saturday afternoon to evening issue. So sunday I played around with it just checking out info online and test driving it seem to run ok but still lacking power. Let it sit till Monday I went out to start it had to cycle key 3 time before it started idle nicely then died would not restart changed ipr valve nothing changed cam sensor nothing changed some how 10 quarts low in oil just changed dec. 30th don't know ? Now will start if I pump throttle and has all its power back?
View 1 Replies
2002 F450 7.3 Turbo
Ok first problem : Starter Motor fuse kept blowing and I spent weeks trying to figure it out. No luck. so wired up a push button just to get the truck started, its a work truck so it was needed asap.
2nd problem : he truck stopped starting completely. Wont start in Park or neutral and after a NEW STARTER (because I thought the solenoid on the starter was bad I replaced it) Everything work correctly for one start with the key. After the second time trying to start it blew the starter fuse again. So I tried the straight wiring to starter. still nothing. I was wondering if there are any shims or anything at the transmission housing to correctly position the starter. I am thinking that maybe the gear is stuck or gets stuck sometimes. when I straight wire the starter it does nothing but the wire gets hot so I know its pulling.
View 3 Replies
I have a 2002 f250 superduty 5.4 4x4 around 317xxx original motor and trans. When it's cold out it won't start at all I have to use starting fluid but once started it will start right back up. Did the plugs fuel filter cleaned the intake and sensors still have a problem plenty of fuel pressure plenty of cranking amps brand new battery and Alternator. It just cranks and cranks when it's warm out fires right up. Runs smooth no lack of power or misfire no codes are being thrown also.
View 14 Replies
Bought a 02 F250 5.4L a few weeks ago. i have replaced the coils and plugs, put in some fresh oil and some other minor things. Last weekend i drove over to my neighbors and back with no issues, until i went back out to start the truck an hour later.
The dash lights come on, but the engine wont start up. i hear a kind of whirring sound coming from a black canister under the hood on the drivers side. I cant use my code reader and I have pretty much exhausted my little piece of diagnostic knowledge. i originally thought it may have been a starter and got a fresh one ready to install but after thing about it i don't feel that's the issue.
I live in a very rural area and bringing it to a dealership would be a 150 mile round trip. What that black canister is? Why it won't start up?
View 5 Replies
I have an 02 250 5.4. 103,000 miles. My truck at random times will not start in below freezing temps. Turns over just fine but Acts as if a frozen fuel line. I can get it running by pouring hot water on the fuel rail or a shot of starting fluid or sometimes both. It's been going on about 3 or 4 weeks now and I have ran through 4 bottles of dry gas with about 15 gallons each time. Also have replaced fuel filter and fuel pressure regulator. I'm 99.9% positive the pump is working and there are no leaks in the lines or holes in tank that I can see. My next step is to drop the tank and clean it out but trying to avoid that.
View 14 Replies
I have a 2002 F250 7.3l with an aftermarket alarm. I can't read what the third letter is on the decal MV? 2000 Modular Vehicle Security. I added a pic of the alarm decal below. The key fob it had was aftermarket for the alarm and stopped working about a year ago. Today I unlocked the drivers door with the key and the lights started flashing and I can hear a clicking sound. It done this a few times back when the key fob still worked and I just kept hitting lock and unlock until it finally stopped. It won't let me start the truck at all and I have tried unhooking the batteries with no luck.
View 4 Replies
My 2002 F250 with the 5.4 (215,000 miles) has a loud tap upon start up, only on the passenger side, heard best in the wheel well. It only lasts about 30 seconds to a minute. It occasionally rears it's head driving around town but only intermittently. Just drove it 275 miles, at 13mpg, truck runs fine, just annoying.
View 9 Replies
I have a 2002 F250 7.3L and it wont start. Its been sitting for the past few days in the cold because the batteries were shot but was plugged in the whole time. I replaced the batteries today and even poured diesel 911 5 hours before trying to start it in case the fuel was gelled. It cranks fine but just wont turn over.
View 2 Replies
Just bought a 02 f-250 7.3 with 115k miles. A couple days after I bought it I noticed a lot of white smoke on cold starts for about 20-30 sec at 50 degree temperature. So I tested the GPR which ended up being bad a replaced with the one that is double in size(name escapes me atm) and also did the 50 cent mod to keep the through-valve cover harness from losing connection since both sides were lose.
After that the temp warmed back up and it would only blow a "puff" of white smoke. The past two days it has gotten down to 30-32 and the truck has a rough time starting. Cranks fine but it's almost like it's getting choked or flooded then it will blow smoke for 3-4 minutes after it starts. The truck does have a FASS fuel system on it with stock injectors. Should I try to Ohm out the glow plugs again or where should I start trouble shooting?
View 3 Replies
My 2002 F250 7.3 randomly dies while driving and seems to only be when I hit a bump no matter the size. I have checked the valve cover harness connector outside of the valve covers and they look fine. I checked the ECM connection took it off and reconnected it.
Changed the CPS censor twice, checked the ICP sensor, checked continuity of all the glow plugs through the valve cover harness. Checked the fuel pump, checked all related fuses, changed the fuel filter, checked glow plug relay, batteries hold good voltage and were recently upgraded to bigger batteries.
Engine runs just a little rough but not enough to be of concern. Air filter is clean and oil level is perfect. What could possible be causing my truck to randomly die when it hits a bump and not start back right away??? This truck is new to me and its the first diesel engine I have ever owned.
View 13 Replies
