Ford Super Duty (1999-2016) :: 2003 F250 - Clutch Pedal Not Retracting All The Way
Aug 7, 2013
I just bought my first Ford. Its a 2003 F250 SD with 5.4L, 5 speed manual, extended cab, 2WD. The truck is experiencing intermittent problems with the clutch pedal.
If I depress the clutch pedal for a long time, then sometimes it does not retract all the way. It does this, for example, when I am at a traffic light waiting for the next opportunity to make a left hand turn.
The truck runs and operates as it should even when this does happen. The easy response is to place your toes under the clutch pedal and pull it aft to its completely released position.
The master and slave cylinder and the booster spring attached to the clutch pedal assembly have been replaced and this condition still continues.
View 2 Replies
Advertisement
I have a 99 f250 sd truck that came as a auto and I am changing it to manual. I bought a slave cylinder unit setup and got it put in and as I was installing rod from pedal to slave I must of broke plastic fingers that hold rod. So is them fingers replaceable or must I buy another unit? with no foot on pedal it sticks up close to bottom of dash now. I tried pushing clutch all the way to floor and still rises too high. What can I do????
View 1 Replies
Pulled out of street this morning and as I was shifting into 3rd my clutch pedal went straight to the floor boards. I was able to keep it in 2nd gear and get it back to my driveway . The pedal will only go straight to floor or goes straight up too the bottom of dash board. It's spring loaded. Am I dealing with a linkage issue?. I had clutch as I pulled out of my driveway and stopped go at the stop sign. Plus I was able to drive it back too my house with the pedal on the floor boards. Where I should look first?
View 4 Replies
I just recently purchased my 1999 ford F-250 superduty V8 5.4 5 speed with 144,00 miles and I'm having a issue with the clutch pedal sticking in and then it will pop out after a couple seconds. It will stick more when I come to a light and have my foot on the clutch but the pickup drives fine and there is no slipping of the clutch. I have never experienced this issue before in any rig I've owned. so I'm a little lost at the moment.
View 2 Replies
I've got a 2000 F250, 5.4L 4x4 with the ZF5 5-speed transmission. Three years ago I replaced the complete clutch assembly, pressure plate, throw-out bearing, etc, and had the flywheel re-machined. Put it back in and all has been well. Only has about 15k miles on it. Earlier this week I went to drive it and all of the sudden it started getting harder to shift and by the end of the trip the clutch will not disengage at all when I push the pedal in.
Furthermore the pedal is much harder to push than it always has been. Checked the reservoir and it's fine. After some searching it seems to most likely be an issue with the master and/or slave cylinder either needing to be bled or replaced. Further reading revealed that bleeding and recommends just replacing the whole system, so I've priced that out. Was it a master/slave issue? Anything else I should check in case it isn't?
View 2 Replies
My stock 2009 ford f250xl 4x4 with a 5.4 and 6 speed has been giving me a weird sound lately started about a month ago and only happens on a cold start situation meaning if it sits over night it will do the sound. the sound goes away after 3-5 min of warm up in my driveway, the sound happens when i push the clutch pedal to the floor. it has no pronounced abnormal sounds through out the rest of the day when its hot which perplexes me, check out the vid on my u tube site for a sound of it.
MAH00111 - YouTube
MAH00115 - YouTube
View 7 Replies
I have 03 f250 v10. just replaced the engine and got everything all connected and started it up and it idles great...the problem is that when you press the gas pedal it starts to drive but then it looses power and acts like its missing. cant get it to go 30 mph. While keeping it floored eventually it gets up to 2000 rpm and then starts to pick up speed.
View 14 Replies
I don't know what's going on maybe some body can shed a little light on this. If you hold the brake pedal down for a long period of time you can feel the pedal slowly go to the floor. So no problem I'll change the master cylinder bleed everything brand new fluid. Don't drive it much we let the sister in law drive it we'll I jump back into it the other day to go to Home Depot and once again I notice it still does it. Could the hydra brake booster be bleeding by or what's else could be causing this it's driving me insane. I really can't imagine the hydra booster causing a problem but it's new to me. I was thinking about bleeding the brakes again thinking there maybe there's air but I have run 2 bottles of brake fluid through how much more??
View 8 Replies
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 Replies
I have a 06 f360 PSD 6 speed. On a road trip and the clutch pedal is getting very close to the floor. No Slippage but the longer I leave the pedal pressed the worse it gets. Are there any good descriptions how the clutch in this truck works?? Slave cyl??
View 14 Replies
Had a No start issue.Turn the key and nothing. Could hear the relays click so knew it wasn't the ignition. Could jump the starter via the wire on the passenger fender so starter good. Replaced the clutch position switch last night. Still have no start but now when I press clutch I have a tow haul light come on dash.If I press it again it turns off. Truck doesn't have tow haul option installed. I hear a relay clicking under the dash too. This is a 2004 Superduty (F550). Replaced the ignition switch today and still same.
View 3 Replies
I Have a 1999 f250 7.3 diesel with the zf5 manual transmission and to shift gears I need to push the clutch all the way to the floor. Could this possibly be the slave and master cylinder or is it the clutch?
View 14 Replies
I have a 1999 f250 that runs and drives great but the only issue I have is when I baby the gas pedal it stalls a little and when I give it more gas it's fine or if. I'm going 50mph then let off gas and then baby the pedal it's stalls a little.
View 6 Replies
2002, F250, 5.4L, ZF-6 trans.
Ok...today by accident turned the key with the truck in gear and clutch not depressed...much to my surprise the truck tried to start and lurched forward.
Is this a sign of a failing clutch safety switch or Could it be an ignition switch problem? Anything else that I am not thinking of?
View 5 Replies
I have a 06 6.0 with 340000 miles on it believe it or not still pulls great. The problem is my clutch fan keeps roaring when I press the gas it's extremely loud all my gauges are fine so the truck isn't overheating? Also not a bad fan clutch I wasted 300 bucks on that and it's still doing the same thing.
View 6 Replies
I'm in the process of replacing the clutch master cylinder in my 99 F250 7.3L. I've got the kit that includes all the components already pressurized in a complete assy. Anyway, I know that in order to remove the clutch pedal component, (the part that stick's thru the firewall) your supposed to be able to rotate it about 45deg and it should pull free from the piston attached to the clutch pedal. But, what happens when it will not come free? I've already got a new replacement kit and I can see where that stainless rod inserts into the plastic component, but I can't seem to get the one on my truck to release?
View 1 Replies
I recently purchased this truck so I don't have any history on it. It's the V10 motor, automatic, 4 wheel drive, with a crew cab. I took it to Advance Auto to have them read codes and it came back with torque converter solenoid fault and 2 other codes related to that part. I didn't get to see the actual code numbers.
I've talked to 2 transmission shops and they said they could throw a solenoid pack into it, but that it might not even fix it. The truck drives fine, shifts fine, the tranny oil looks and smells fine, so I'm tempted to not worry about it until something else happens.
The truck has 217,000 miles on it...
View 10 Replies
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission.
I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced.
I have also just had a new hydraulic clutch kit installed.
View 5 Replies
My issue, just purchased f250, 2004, v 10, manual transmission, state vehicle with 32,000 miles but was a plow vehicle for localRMV lot, that said, great shape and runs strong but I get a clunk and shutter when I am in reverse and only when I push down clutch before stopping. Doesn't do it starting forward or reverse, only reverse and when I push clutch in before stopping. Did have a friend drive and looks like the transfer case is moving, as if mounts or bolts are loose. Does this make sense and could bad slip joints be putting excess torque on ?!?!?
View 4 Replies
The other day I got in my truck and started down the driveway when I realized I had no brakes, I slowly backed up and parked it. I haven't driven the truck for approx. 2 weeks and it seemed fine then. The master cylinder is full, there are no signs of leakage from wheel cylinders or lines. Today I unscrewed the left front zert and no fluid came out. My pedal goes all the way to the floor.... Whats going on, and if its a easy fix?
View 14 Replies
I don't know whats up with my new truck, its a 04 f250 scsb, 4x4, 5.4l with 61k orig miles on it. Truck will stop on a dime, has NO pedal sinking, but it takes about 3/4 of the pedals travel to apply pressure to the pads and have the truck stop, sometimes if I push the pedal down then let up and push it again the pedal wont travel as far, I just flushed the system today, no air in the lines, is there a bleeder on the abs? truck has 4 wheel abs...
View 14 Replies
