Ford Super Duty (1999-2016) :: 2003 - Pedal Would Sometimes Lose All Response And No Gauges
Jan 10, 2013
2003 f250 4x4 7.3 auto
Been an ongoing problem with truck, pedal would sometimes lose all response. truck starts and idles fine but will not throttle up and all needles on the instrument cluster are at their rested position and the odometer doesn't even light up, however all the backlights still work fine.
The owner said that a 10 amp fuse on the bottom row of the fuse panel would occasionally blow, and that's when the pedal would go dead, he would replace it and keep driving till it blew again... usually about a week. I checked all fuses on the truck tonight and all are fine.
Unplugged the connector on the pedal sensor and cleaned and reinstalled and still wont throttle up. I am not sure what number the fuse was that he kept replacing but i *think* it was a cluster fuse. Is their an correlation between the cluster stopping the pedal sensor from working or vice versa?
View 14 Replies
Advertisement
I need fixing my 2003 f350 6.0 diesel, I have been working on this truck for a while and still am having problems, here was the original symptoms:
-Hard start or no start on a sunny day
-Rough idle for 10-15 minutes
-Rough shaking in the low RPMs (35 mph)[/COLOR]
-Slow response from the gas pedal
-boost would only get to 14
My dad and I then did many things to the truck in the shop, those things are:
-Air test and replacement of coupling going into oil branches (next to HPOP)
-Replaced EGR valve (no good)
-Replaced ICP sensor (leaking oil)
-Replaced ICP sensor and IPR valve piggtails (due to frayed wires)
-Cleaned Turbo
-Cut MAP sensor hose and reattached it (spliced on the end)
-New battery
-Performed a bubble test and found two bad injectors on passenger side (injectors #5 and #7)
-Cleaned and lubed tops of injectors
-Replaced O rings and copper crush washers on all injectors
-Replaced nipple cup O rings (tight)
-Blew out injector cups
-Bubble tested after injectors put back in (no more bubbles)
-New FICM, EGR cooler and oil cooler were already installed
-Ohm'd main engine wiring harness (good to go)
-Taped up frayed wires on fan clutch connection
-Increased wire gauge on the positive jumper between both batteries
-Sanded each ground on the batteries and engine, cleaned battery clamps, lithium greased connection points.
-Checked fuel for air (no air)
-Checked fuel psi (85 psi, plenty)
-Oil changed
After doing all of this (diagnosing as we fixed each thing) we now fixed many things including the hard/no start problem. Now, for the first three to five minutes:
-It starts right up
-Runs perfectly, no shake and instant response from the gas pedal and turbo
-Boost goes to 28
-ICP is 800-950 on idle
-IPR is 25-26.9% closed
After five minutes however:
-Starts to shake
-IPR % starts to raise
-Received no response from gas pedal (absolutely no power)
This truck has been torn apart like 8 times and I have to do it on my spare time.
View 13 Replies
I have a 2002 f250 7.3 with a dead pedal and gauges. This has happened to me once before checked fuse 45 and it was blown. I didn't know that the po used a 30 amp fuse when it should have had a 15 amp. I replaced it with a 30 not knowing. Well coming home the other night it happened again gauges dead and pedal. Checked fuses all were good. Found this site and read about the cause in the shifter. Took that apart and fixed the wire that was broken in half. My question is what else is fried now from having a 30 amp fuse in while it was shorting out since I have no gauges and gas pedal.
2002 f250 banks six gun
banks 4 inch exhaust
View 2 Replies
2003 f250 5.4 86000 miles. When I start the truck, "especially after it sits a day or more" it starts to fast "Rushes". Like the gas pedal is all the way to the floor. I have taken it to the Ford dealer and they say they can find nothing wrong. They say all fords start up fast but I know this cannot be right. If I start it and let it run awhile then start it again it starts much slower. It only rushes like that a second or two and slows down. Today I noticed that when it started all the gauges pegged out. The speed indicator went up past 100mph sitting still in park. Then they all dropped down to zero then back to where they should be.
View 3 Replies
03 f 250 super duty, my battery light came on and when I accelerate my dash gauges shut down and radio turns off, if I idle or stay under twenty MPH, everything works fine. Battery and alternator test good, lights never dim, any thoughts
View 4 Replies
My 1999 F250 V10 has started to lose power off and on. It will run fine then when I stop at a light or sign, then when I take off it runs like I pulling something heavy. If I stop again it goes back to normal sometimes. 161000 miles. No check engine light is on. Motor idles perfect and sounds great. I don't know anything about motors...
View 4 Replies
All of a sudden steering is WAY to easy i can flip it one way or the other with my finger. Front end is tight no lose tierods etc and no play in steering box when you turn it the steering turns immediately.
Thinking power steering is going bad maybe over pressure? Repair will be a pain has central hydraulics lines all in way. 2000 F450 7.3 ....
View 2 Replies
I have a 2015 SD with only 4100 miles on it. This has happened to me twice. Both times, traveling slowly at idle or just above. Anyway, tried to give it a little gas, and -----nothing. Lightly pumped the throttle a couple of quick times and back on line. The motor didn't die, but there was no response to the throttle at all. The first time, I thought maybe it was something I did. Then it doesn't happen for a month and a half and then again, in heavy traffic in the rain. Haven't had my first service yet, and you can bet I'll tell them about it. Almost felt like a two-stroke that had loaded up?
View 2 Replies
I just bought my first Ford. Its a 2003 F250 SD with 5.4L, 5 speed manual, extended cab, 2WD. The truck is experiencing intermittent problems with the clutch pedal.
If I depress the clutch pedal for a long time, then sometimes it does not retract all the way. It does this, for example, when I am at a traffic light waiting for the next opportunity to make a left hand turn.
The truck runs and operates as it should even when this does happen. The easy response is to place your toes under the clutch pedal and pull it aft to its completely released position.
The master and slave cylinder and the booster spring attached to the clutch pedal assembly have been replaced and this condition still continues.
View 2 Replies
I have 03 f250 v10. just replaced the engine and got everything all connected and started it up and it idles great...the problem is that when you press the gas pedal it starts to drive but then it looses power and acts like its missing. cant get it to go 30 mph. While keeping it floored eventually it gets up to 2000 rpm and then starts to pick up speed.
View 14 Replies
2002 Ford F350 Powerstroke, 7.3L, Automatic, 4 wheel drive .... AFE Stage II Intake, 5" full exhaust, TS 6-position tuner chip, Swamps 140lb injectors
Intermittent accelerator problem: no response, just goes to idle. Runs perfectly with no other issues but zero response when the accelerator it pressed. There seems to be no pattern to the problem as this happens at any speed/position on the pedal. When the accelerator goes out the check engine light in the lower left corner comes on. All fuses are good.
Symptoms began a month or so ago feeling like an occasional 'hiccup' or hesitation. Symptoms occurred a few more times until a couple of weeks ago (Friday, 2/20/15) when it left my son stranded a few miles from home. He was able to limp it to a parking lot and we left it over night and went and towed it back to the house the next morning. The truck started and ran fine just no accelerator so we towed it idling so we would have power steering/brakes, etc. As we neared the house the engine light went out and the accelerator began working and he was able to drive the truck the remaining 1/2 mile home.
Most all of the research I did came back with the Throttle Position Sensor as the culprit. I was able to order one (the complete accelerator pedal assembly that is*) at a Napa store in a nearby town and picked it up on Tuesday (2/24). As soon as I installed it everything worked fine.
As an aside, I have read a lot about the mid-2001 switch from the units with the TPS (Throttle Position Sensor) and IVS (Idle Validation Switch) as separately connected units to the 'new' style where these parts are combined into one and there is a single 5-wire connector. Being a 2002 there was no question as to which one I had. Just be aware of the difference. Also, this part is simple to change. The connector has a clip that you pinch down on with your thumb and then pull off. I use my little electric impact with 1/4" extension and a 10mm socket. Zip, zip, zip an you're done. It takes me longer to get my tools out.
A few days later on Friday (2/27) it presented the sporadic accelerator symptom a couple of times again but was able to get the truck home. The next morning I unplugged, cleaned (CRC Contact Cleaner), and dabbed into the connector a small amount of dielectric grease to insure good connection. (I had read that in my research as well). That seemed to work beautifully and he said it ran fine all day and until the next afternoon (Sunday, 3/1) when it began acting up yet again.
I continued to research and could find nothing that would suggest anything other than the Throttle Position Sensor. I read that some other folks had gone through a few of the Napa/aftermarket units though so I began thinking that maybe I had just gotten a bad unit.
View 9 Replies
I have a 2005 F250 5.4L 2wd. Parked the vehicle in my driveway and the next morning there was no response from the accelerator and the CEL light and the wrench light on. I pulled the codes and came up with codes P2104, P2107 and P2110. The KOEO code was P2122. I checked the wiring and connectors and all appear to be fine I replaced the throttle body and no change. I removed the accelerator pedal and tried it on another vehicle and it worked fine. I have power to pin 16 on the diagnostic port. After clearing the codes and rescanning the same codes come up immediately.
View 14 Replies
The Truck: 2011, 250, 4x4, Super Cab, 6' box, 6.2 with 6R140, currently 40K miles. It did have an 8' plow on it. An 80 year old gent plowed his personal 200' driveway with it for 2 winters before I bought it. You can tell the truck was taken care of, or I wouldn't have purchased it. I have all the service records. He had his local dealer do all of it. Plow and all the controls were removed prior to my purchase.
Scenario: Trucks cold (summer ambient). Driveway has a grade down to road. Doesn't matter if I am nosed or backed in. Start up, back/pull out of driveway on to flat road, and very slowly take off. The 1-2 shift produces a lose thunk sound and sensation, very faint not loud. Almost Like a lose motor mount. Only will do it once, only on the first start and 1-2 upshift. Ive tried to reproduce it after the first occurrence, no luck. If you gas it under the same circumstances it wont do it.
It doesn't necessarily feel like an internal trans problem. More of a "somethings just lose enough to shift or move" problem. Sounds like somethings hitting the frame, core support, cab floor on this slow 1-2 up-shift. Its upfront passenger side. I've spent several hours under it looking for lose items witness rub marks etc...to no avail
Again it only does it after it sits or upon the first start in the AM or when leaving work PM. Not when its warm.
View 14 Replies
Took delivery of my 2015 F250 in June with 2WD and the 6.2 gas engine. What I thought to be a slow throttle response seems to be more of a quick shifting transmission according to two different dealerships. My 6 speed automatic has already shifted to 4th gear at only 25-30 MPH. My Dodge Hemi I sold never had shifts as quick as this and I think it's to quick. My question is....is there a way to change these shift points so I get more speed before it shifts into the higher gears?
View 10 Replies
My friend has a F250. He was getting terrible mileage and the mechanic he took it to replaced the intake gaskets. After that the mileage went to 12 and he was happy. Now its down to 6-8, just highway. It seems to me the throttle response is terrible compared to my dad's 01 V10. And it sounds terrible. Exhaust manifolds aren't leaking that I see.
I've got AE and have hooked it up, but I'm really not very familiar with these trucks. I don't get any codes that would relate to anything. Had one trans sensor code but that was about it. Key on engine running test didn't say anything.
View 5 Replies
2005 f250 4x4 , crew cab v10. Just put on my magnaflow muffler and gotta say, What a difference that makes! Can't wait to get the k&n intake kit and see what that will do. I see that my truck has the electronic throttle control instead of the previous v10s with the cable. I am wondering, is there any way to get quicker throttle response like with the old cable style throttle? Just seems real sluggish to rap up the rpm in park with no load on it.
View 1 Replies
In a 06 F250 the gauges and radio die randomly while driving. The dash lights stay on though. What can I check or replace?
View 5 Replies
I have a 1999(03/98 Production Date) F350 DRW Dump 5.4L Reg Cab. I just replaced the ECM (Drivers side Kick plate) with a used ECM
1. Crank but no start, gauges worked.
2. Replaced the ECM (Drivers side Kick plate) with a used ECM
3. Truck now starts.
4. None of the Instrument gauges work. No gas gauge, no speedo, no tach, no bat no odometer or trip odometer. Not one single gauge works.
Does the ECM need to flashed for the cluster to work or might it be a separate issue?
View 2 Replies
I have a 2002 F350 with the triton 5.4. For the last week it has been running like crap. I just did my plugs about a month ago. I don't know if it's a miss fire or bad fuel or I don't know what it could be. It's a popping sound coming from my exhaust and when it happens I lose power. It happens off and on. One second it will run fine and normal and the next runs bad. What it could be. Today I just changed my fuel filter and added STP octane boost and fuel injector cleaner. Haven't seen a difference yet.
View 4 Replies
I don't know what's going on maybe some body can shed a little light on this. If you hold the brake pedal down for a long period of time you can feel the pedal slowly go to the floor. So no problem I'll change the master cylinder bleed everything brand new fluid. Don't drive it much we let the sister in law drive it we'll I jump back into it the other day to go to Home Depot and once again I notice it still does it. Could the hydra brake booster be bleeding by or what's else could be causing this it's driving me insane. I really can't imagine the hydra booster causing a problem but it's new to me. I was thinking about bleeding the brakes again thinking there maybe there's air but I have run 2 bottles of brake fluid through how much more??
View 8 Replies
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 Replies
