Ford Super Duty (1999-2016) :: 2008 F350 - How To Locate Keyless Entry Code Sticker
Feb 20, 2010
I have looked at many of the other treads and I can not find the answer. How do I locate the keyless entry code sticker in my 2008 F350? I just bought the truck used, I do not have the card that is delivered with the truck and I don't want to pay the Stealership to hook it up to there computer. I am looking for the RAP or the computer module as it is called in the owner's guide.
It is not behind the glove box, there is no longer a fuse access panel under the dash like the earlier SD's, the drink holder under the upfitter switches does not "pop out." Before I start with any tools, I am looking for input.
View 14 Replies
Advertisement
Do the wiring for keypad keyless entry is in the harness and the programing in gem module on a 2003 F350 crew cab?? It would seems that is the same harness/parts as the excursion. I have not removed door panel yet, just trying to save some time.
This truck is one of my finest 4x4 rides yet, this would make much better!!! when i picked up my truck, included in the owners info was a factory keypad keyless entry code card, dealer told me that all trucks with keyless have that card regardless if it has keypad or keyless remote entry???
View 5 Replies
I can't remember my door code and don't want to take it to the ford dealership and pay. I know there is a code up under somewhere but I can't find it? 2005 f-250 lariat.
View 10 Replies
I just bought an '08 F350 Super Duty CC. When I bought it, the previous owner gave a me card with the code on it. So I tried to reprogram the keyless keypad to a new code that I can remember, no luck at all. Followed all the steps on how to reprogram it like a hundred times and still won't reprogram. So I've noticed that none of the lights light up except 7*8, none of the other buttons won't light up.
Could the keyless keypad be going south? Maybe the contacts in the keyless keypad are gummed up or a relay? Need to get this feature to work cause I sure would use it a lot. Also how do I remove the interior door trim to get to the keyless keypad? The door panel has electric locks, electric window, power mirrors, telescoping rear view mirrors, memory seating buttons and speaker pillar.
View 9 Replies
I have got a new 4 button key fob for my 05 F350. How to program this unit for the keyless entry and the remote starter.
View 9 Replies
The key ring part of the fob for the keyless entry on the truck (2006 F250 V10) broke a while back. Finally got around to buyin a replacement only to realize that the keyless entry that came with the truck is not OEM. It's an Omega L2M 4410.
In trying to cycle locks to replace the fobs, the locks will not cycle. Tried everything that can be found on forums, youtube, etc. all to no avail. This leads me to believe that the aftermarket keyless was put on because there wasn't keyless from the factory.
I have experience with installing aftermarket systems, but this one stumps me - can't find where the system was installed in the first place. To me, this sounds like it should go to a shop for further investigation.
View 4 Replies
I recently purchased a 1999 F250 S/D v10 5 speed ext. cab and only received one ignition key (no keyless entry fobs).
The truck does not have a keypad on the doors, but if this truck has the remote keyless entry option, how can I tell?
View 14 Replies
I am trying to put in after market keyless entry on my 03 sd wired up my relays according to the 5 wire alternating door locks found on this page
[URL]....
but it keeps popping my fuse when I try to put it in, if this is even the correct set up I found another guy on here that used the same set up but never said if it worked or not
View 6 Replies
I have the factory keyless entry on my '03 F-250 SuperCab. I have always had to be within about 5'-8' of my cab to get the doors to lock/unlock. I thought it was normal for the longest time, but recently learned it's not. I am out of warranty now so I need to try and fix this myself. What is the location of the receiver module, and what it looks like? Also, is there an external antenna w/ the factory keyless entry, and where is it at? Transmitters are fine, as is battery power. Only think it could be is receiver/antenna.
View 14 Replies
My 'new' 2004 F250 ExtCab SB w/5.4L sometimes 'drops' my keyless entry (key fob) for no apparent reason. Also, when I attempt to do the 'eight turns' of the ignition to get into program mode, it doesn't always work the first time (or second, or third, etc). Is this a common problem?
View 5 Replies
Is it possible to add the factory keyless entry without replacing the complete dash harness? I have an aftermarket unit I can add but I'd rather have oe if possible. Truck is an 2003 f250 v10.
View 1 Replies
2008 F350 6.4 ... So I've been reading all about the spartan tuner throwing the P0088 code, and the ford band aid fix, I guess my question is, I'm going to have my HPFP replaced for peace of mind. Truck has 106,000 miles on it. Will i have an issue at the dealer if I show up with my tuner/exhaust on the truck? I'm not worried about warranty obviously, I just want to know are they going to have to unplug the tuner? Or something, I am just concerned how they'll go about putting the new HPFP on.
View 6 Replies
I keep getting a lean bank code. I have cleaned tb and replaced one of the rubber lines. It only comes on when I take a good ride with the truck. Not sure what else it could be. I'm thinking O2 sensor maybe.
2008 F-350 5.4 3V. 65k miles
View 9 Replies
Replaced HPFP 38,000 miles ago. Truck began going in limp mode without engine light, wrench came on in dash, gave codes for brake switch, anti-theft, some other weird codes. Had those codes cleared, ran for while then water separator came on, drained the water out, came back on. Read some forums, so I removed and cleaned the housing, cleaned off the sensor. Had code cleared and ran good for about a week. Then guess what engine light comes on, limp mode.
Went to Auto Zone, pulled code P0088. This truck runs awesome until limp mode. No other problems. I take it to the ford dealer, scanner pulled P0088 and the water separator code again. I have read alot of remarks about this P0088 code. Can there be another cause for pulling this code, only 38,000 miles later. I had them do the TSB 12-07-07 but I have also read it can only be done if the P0088 is the only code. I just really feel there is an underlying issue with these 6.4's.
View 3 Replies
I am looking to replace the 4x4 offroad sticker on the side of the bed and wanted to know the dimensions. I've been looking on eBay because dealer wants way too much for stickers. just want to make sure I get the correct size.
View 5 Replies
I just bought a 2006 Texas Edition F150 with key less entry but the instructions and assigned codes did not come with it. How do I find what the code is to operate the system?
View 8 Replies
Where can I find the key pad code on an 08 escape? I don't have the card in the glove box and I don't want to pay the dealer. It should be printed on the security module box. Where to find it? On my f250 it was under the dash behind radio.
View 14 Replies
Long story short, I need to replace the box on my 2008 F350. Do the boxes from '14-'15 models line up? I know the fuel door is different, but is the rest the same?
View 4 Replies
I have an 08 f350, and my cab over lights are out...I've checked net for issues and they all point in different directions... Running and towing lights are fine, just cab over lights are out...is there a fuse somewhere I cant find? could one burned bulb be out and it effects all?
View 3 Replies
I had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 Replies
2010 F350 in my shop today. so, before dismantling the entire top of the motor for this inbred oil cooler job, is there anything else responsible for the P012 engine oil temp issue? it throws the wrench icon and cuts power and i pulled the P012F code.
View 9 Replies
