Ford Super Duty (1999-2016) :: 2008 F250 Truck Will Not Start Whenever It Rains
Nov 30, 2014
I have an 08 f250 with 6.4. when ever it rains the truck will not start. None of the gauges will work, door chime doesn't work and the only error light is the airbag light. Lights, radio, turn signals, horn all work. There is no clicking of the starter relay, the truck in dead. There is no water on the floor board nor is the floor moist. If I place a ceramic heater on the driver side floor board and blow hot air towards the firewall the truck will start in about 30 min to an hour depending on how long it sat in the rain. I've removed the air intake vents and there is no debris blocking the drains.
View 3 Replies
Advertisement
I have a 2008 f250 with 5.4v8. The truck starts intermittently. Put key in turn if no dash lights it doesn't even crank or hear a click. If u put key in and turn and dash lights up to starts and runs. U can watch the different lights (instrument cluster) light up independently like a xmas tree. When truck doesn't start if u disconnect battery when touching power wire to battery. Post truck lights will flick on/off if u tap cables to battery and leave on. Lights flicker on/off and then stay off. (Don't know why shouldn't flicker at all) after disconnecting and reconnecting battery truck will or will not start still depends on if dash lights come on before cranking.i replaced battery, starter, alternator, all the ground cable connections and wire cleaned. I haven't replaced the power side but are clean.
View 3 Replies
So I'll be driving down the road and the gauges will randomly start jumping around then the truck will just shut off, this just started a couple days ago, it seems to be gaining in frequency, when i try and restart the engine all my warning lights flash on and nothing happens, try again and it starts back up, now the last time it happened all of the above happened but it was followed by a fast clicking noise from under the steering column, it has to be a electrical issue as i have full tanks and motor is in tip top shape. Also no codes pop up with my code reader.
View 1 Replies
I have a 2008 f-250 4x4 extended cab, I picked up a set of black rock steel wheels 17x9. I now have 265 70 17s on my truck. will these wheels work and with what size tires.
View 4 Replies
I have randomly getting in my sd. It is an 08 f250 xl with a 5.4. randomly my truck chime at me, hence why I haven't been able to capture it on video. It will chime twice. The sound is a subtle bong, bong. It is never predictable and never affects anything, but is annoying and I am curious as to why it does it.
View 14 Replies
2008 f250 standard cab long bed 2wd base model 5.4. This thing has been great for the last few years i i owned it but it developed a shake since i got new tires. My mechanic mounted 4 new Hercules Terra trac at 2's on my 18 inch wheels (275 70 18) and when i got the truck back it was shaking violently at anything over 45. Mechanic says the new tires are heavy and its affecting other things...sounds plausible. So here i am a month later with a New steering stabilizer, all new ball joints, new shocks, new u joints, and 1 new tire (he said 1 of the brand new Hercules had a broken chord). The shake is 80% gone but this truck is still not the same. Anything after 65mph and it has a feint wobbly bouncy shake. I don't think its the dreaded hop that everyone gets on these. I have 2 theories:
1. These cheap tires just suck and will never be right
2. The cheap junk Monroe shocks he put on are way too soft to do anything
so what do i do? Should i get some crazy shocks or will that make this truck even bouncier? Im worried about making it even stiffer than it already is.
View 12 Replies
I have a 2008 F250 crew cab lariat 4x4 with 20 inch factory wheels that the steering wheel shakes during normal driving left to right. I bought this truck with 1500 miles on it. This shaking started at 50k miles and I was thinking it was a balance issue so I got new tires a month later since mine were about worn out anyways. They were factory replacement nitto terragrapplers. Shake was still there, swapped out for another set of nittos and shake still there, swapped to BFG AT KO's and shake better, but still there. I have gone through 10 or so balances, 5 roadforce balances, 2 alignments at 4 different shops including the ford dealer through the 3 sets. My wheels are scratched to hell and back from the careless people at the tire stores from so many balances.
My truck sat at the Ford dealer for a week just the other day and they changed the steering stabilizer. I thought it was gone, but a a few days later shaking started again. It almost feels as if every little bump, rut, crack in the road the steering wheel feels and shimmies (doesn't matter the speed, gets worse and more noticeable at higher speeds). The Ford Dealer says can't duplicate, but then when I go down there and test drive with them it's "oh yeah I see that, it shouldn't be doing that". The Ford Dealer says they can't find anything loose in the front end when I tell them to check tie rods, bearings, etc.
My truck has 62k miles on it now and it's driving me to the point of thinking about trading it on a Chevy. I love my truck, but it kills me everytime I make a payment and it rides like crap. I am still under extended warranty so I need to get this fixed before it goes out. I've also noticed that if I turn my steering wheel back and forth real quick while driving like warming up for a Nascar race I can feel a bumble in the steering wheel. This is NOT the death wobble as I use to get that around the 20k mile range and it disappeared and has never been back.
View 14 Replies
I just bought a 2000 F250 SD, 4x4, 5.4, Quad Cab. I drove it off the lot, stopped to put air in the tires, jumped back in and it wouldn't crank. All of the dash lights worked fine. Tried jumping at the starter solenoid and got nothing. Got under the truck and jumped it off the starter, vroom, fired right up. Replaced the starter solenoid and had no issues for about 2 hours. Then it did it again. This time it wouldn't start at all. I towed it back to the dealer and they had it for 3 weeks.
Then yesterday I called and they said it was done. Picked it up, drove to the barber shop, got my hair cut, came back out and it did the same thing AGAIN. After jacking around with the shifter and turning the wheel back and forth 100 times it started. The key is kind of hard to turn sometimes in the ignition, so I'm thinking that the ignition cylinder needs to be lubed real good, but that shouldn't stop it from cranking the motor over, right? I was going to swap out the ignition switch, but I don't know if that will do any good either.
View 3 Replies
I have an issue with my 2008 f250 6.4 where the gauge cluster is dark and truck won't crank. The only light on the dash is the airbag light. I have tried reprogamming with my Spartan tuner, checked fuses, removed aftermarket alarm, charged batteries. I scanned and got two codes. P1260 theft detected and a u code no comm with cluster.
View 7 Replies
I have a 2002 F250 7.3l with an aftermarket alarm. I can't read what the third letter is on the decal MV? 2000 Modular Vehicle Security. I added a pic of the alarm decal below. The key fob it had was aftermarket for the alarm and stopped working about a year ago. Today I unlocked the drivers door with the key and the lights started flashing and I can hear a clicking sound. It done this a few times back when the key fob still worked and I just kept hitting lock and unlock until it finally stopped. It won't let me start the truck at all and I have tried unhooking the batteries with no luck.
View 4 Replies
I have a 2010 F250 V10 4x4. about every 3-4 times when you start the truck....it seems as though the starter "sticks". If I catch it and shut it off and then turn the key right back it fires up and does not stick. Its as if the gear is staying kicked out into the flywheel. Are we thinking the starter itself? I'm thinking starter...but looking for input before I crawl under it.
View 1 Replies
I have a 2001 F-250 XLT 4x4 with V10. Truck will not start. No fuel pressure. My Haynes manual does not show ignition or fuel delivery wiring. I have found the relay box behind the radio/dash. I need a wiring diagram and info on which relay is the fuel pump relay. Want to know so I can jump relay to see if fuel pump is okay.
Truck had sat for a few weeks being ran very little, so had to jump start yesterday. Ran for about 15 min, the shut off, re-started and ran for 30 min. Truck sat for about 1.5 hours then would not start. Charged battery overnight and it is 100%.
View 3 Replies
Ok truck shut down wouldn't start back. Put fuel filter o. Frame cranks but won't start. Was told has high pressure oil leak in engine?
View 8 Replies
I have a 2002 F250 7.3L and it wont start. Its been sitting for the past few days in the cold because the batteries were shot but was plugged in the whole time. I replaced the batteries today and even poured diesel 911 5 hours before trying to start it in case the fuel was gelled. It cranks fine but just wont turn over.
View 2 Replies
I have a 2011 F250 with the 6.2 gas engine. I have been having a problem that the dealership says there is nothing they can do and have never heard about.
After the truck sits all night I get in and drive it for 10-15 min. It gets warm and I get out turning it off. When I come back about 15-45 min later I start it up and go to leave. As I pull out and start to accelerate in first gear the truck goes to an idle for about 2-3 seconds. I push the gas pedal and get no response. After a couple of seconds it picks up wherever you have the gas pedal. If you have the pedal to the floor it jumps you forward. This is not putting on any lights and the computer is not throwing any codes. According to the dealership the computer is telling them there is nothing wrong.
This has happened 12 times in the past 6 months. It has happened since I bought the truck. I have just started documenting it as of 6 months ago. It is not something I can make it do on command. After it happens once it doesn't seem to do it again for a week or two. I have 31000 miles on the truck. The dealership has had it for 4 days now and can't seem to get it to happen for them.
View 2 Replies
Pulled into parking lot this morning, 05 F250 CC 4x4 V10, truck starts dinging at me, Park brake light comes on. Ease off of gas and idle around to parking place, no sign of brake drag. Release Park brake, no difference, set the brake and release, no difference, guess the microswitch went bad. Not raining, never hit a bump, MAY have had my foot on the brake, but that shouldn't effect the P Brake.
After setting for the 12 hour shift, all is good and well. Did not come back on.
Where this switch is? Is it under the cover by the foot set or under the truck along the cable? Would like to know where to look next time this comes up. Did have 2 new tires installed on the front a week ago, new tierod and aligned at the same time.
Just wondering and curious, my last F150 had all kinds of electrical germlins in the windshield wiper arm.
View 8 Replies
I have a 2004 f250 with a 5.4l and it won't start. I went to leave the store and went to start it and the truck started when I turned the ignition on not when I engaged the starter so I drove home anyway but there was what sounded like a spraying noise coming from underneath the truck all the way home the truck did die once on the way home but started right back up without me doing anything. Got home shut the truck off now it won't crank or anything all my lights and everything come on like normal just won't crank. What the problem is?
View 7 Replies
I have had this issue with the truck 2008 F-250 6.4L since I bought it a year ago. At first it seemed as if the truck wouldn't start whenever the water temp gauge was working while she was hot. When the gauge wasn't working she would start right up like a champ. Well a year later ( have only been driving it for 6 months) a full engine rebuild, new high pressure fuel pump ( injector pump on top the engine below the turbos) she still won't start when she is hot. What the issues are.
Right after the engine rebuild I was getting the p088 code which is for the hpfp but since I cleared the codes right after the engine was rebuilt I haven't gotten the code again. I replaced the high pressure fuel pump this last weekend hoping that it would solve all of my issues and she would be like brand new again, but it didn't do anything. When I ran codes right after I installed the high pressure fuel pump I got a few codes p0684 which is the glow plug control module p0284 ( google said) gear lever y position correct but I'm unsure if that's right.
P0528 which is the fan speed sensor circuit ( that was unplugged during the removal of the hpfp and power steering pump or the radiator) p0480 cooking fan circuit ( also unplugged ) p174e out put shaft wheel speed correlation ( not concerned about that one) p008c fuel pump control circuit p008d fuel cooler system ( taken out and unplugged using installation of new hpfp) p115a ( low fuel level forced limit power) that is from trying to start while she had a little bit of air in the system after replacement) p2291 injector control pressure to low- excessive cranking ( probably from the air in the fuel system again). I cleared all those codes once I got her up and running again. Checked for codes yesterday and the only one that came up again was the p0684. Where to check next for this hot start issues,and don't know what to do at this point.
View 4 Replies
I have a 2008 f 250 super duty gas v10 i have never had problems with it start always starts right up and strong. After coming out of the story today I tried the remote start and it tried to turn for a couple seconds and stopped. I replaced the battery and starter and still nothing. i hear the relay when trying to start with both keys or remote start but nothing from the starter all lights are working .
View 1 Replies
Just picked up my F250 a few days ago and it's been great up until yesterday when I hopped in to start her up and nothing. It's a brand new battery and all lights worked, but the dash was dead. I attempted in vain for an hour or so to diagnose as to why this was happening and just happened to open the door with the key in the ignition and hit the door lock button....all of a sudden the truck starts beeping and the message on the dash said "to disable alarm start vehicle". I turned the key, the dash lighted up and away I went. What I may have done to cause this or has it happened to you? I'm thinking it's something with the key fob but not sure.
View 6 Replies
I have a 2008 Ford F250 V-10 Superduty and recently I had a transmission cooler line start to leak. I ordered replacement lines and the tool for the quick disconnect. The line that's leaking is from the radiator to the quick disconnect. I was able to replace the one line, however the second line (problem area) has been a nightmare. The line cracked right at the quick disconnect fitting.
The hard line is tight in the fitting and corroded. broke the tool trying to remove from disconnect. The line is flush with the quick disconnect. How to get that out of the fitting? or another method of fix? Its a hard 1/2 line going into connect crimped to rubber line going to transmission.
View 13 Replies
