I have (2) 2014 f250's both have given the trailer disconnected message randomly from the day they were new. Dealer says everything is with in specification. I just live with it now but something must be wrong with the design. Only does it when no trailer is connected an might be worse when it rains. Might have to hit the ok button every 10 minutes so on bad days.
View 14 RepliesMy 08, when I connect my 7-pin trailer up, bouncing down the road that message and tone CONSTANTLY going off....drives me nuts! I have went thru the wire harness 2x now, cleaned all the contacts, etc. Any other thing short of a 12 gauge? When it does pop on, the controller starts flashing...I've reached down a few times and manually hit the brakes and it still hits em so whatever it is, I feel its very minor or whatever....just don't know where to go now! All contacts have been cleaned good as well.
View 8 RepliesI've got an intermittent Trailer Wiring Error message that started appearing with a trailer connected on my '11 F250.
Brakes and lights work OK on the trailer, I thought I had read on the board here that there was a TSB for this, but I cannot find it.
I tow a 5th wheel with my 2014 F-250 that has an factory TBC. I just installed Electric over Hydraulic disc brakes on my 5th wheel and was trying to see if there was a setting I needed to change on the TBC to tell it that is now E/H versus E. In the Information section of the dashboard display it talks about the controller actuating electric drum brakes but the manual talks about it being able to do electric AND E/H. What I need to do here...if anything?
View 6 Replies2012 F250 Lariat with 18k on the clock. FOr the past two months I've had a temporary side job on weekends and had to haul some trailers. I noticed my trailer gain operates sporadically and if I try and adjust it she tells me there's no trailer connected. I've edited the settings and reset all the settings also. I find this particularly annoying when towing the 4,000 lb trailer but I'm also hauling single axle trailers and it hasn't registered that I'm towing once.
View 14 RepliesDriving the truck today I noticed mssg from info on dash " problem with trailer wiring". I wasn't hauling anything. the message went away on my next stop when a truck was turned off. On my next stop, I was pulling into a parking space truck stalled and I saw another message saying something like " please pull over safely and stop a truck." Luckily I was already parked. the truck would not start or even turn over. after about an hour truck started but brake symbol was on the dash.
View 10 RepliesEvery time I touch the brakes I now get a very annoying beep and an error message that says "wiring fault on trailer." I don't have a trailer hooked up so not for sure what's going on. The error message on the console I can live with but that loud beeping is driving me crazy.
If you hit the brake and keep the pedal depressed, then you only get the initial beep and then it goes away. The problem for me is I live north of Dallas so if I'm in traffic then I'm constantly hitting the brakes. I called my dealer today so I'll wait to hear what they have to say.
I have a 2005 Ford F-250. I have checked power to the rear harness and all is good except for the tail/running lights.
Is there a fuse for the tail lights? I have checked the manual and don't see one called out. And the relays under the hood are labeled stop lights/turn signals and those are working fine.
I will see if I can trace the brown wire from the rear harness backwards, but it may be a simple fuse.
Any info if the "Aux" terminal on the trailer harness wiring on '01 F250s is for reverse lighting? I'd like to put some on my stock trailer. Also, is the "12v" terminal feed switch operated or hot always?
View 2 RepliesI have a 2005 ford f250 with the factory installed brake controller and towing package,until recently all was well,I tow a fairly large travel trailer and last time I hooked the trailer to the truck I noticed the running lights on the trailer were lit, I checked to make sure that I did not have the parking lights turned on or the headlights. I did find posts about the running lights not working and was surprised to find there is a relay somewhere on the central junction fuse block that was integral to the cfb and not user serviceable. Could my problem be that this relay failed in the closed position or am I not going in the right direction in my quest to find this problem. Also looking for a diagram of where this relay is located on the central junction fuse block? I would also consider doing a work around solution rather than having to replace the entire fuse block.
View 7 RepliesWhere I can find a good used or a good deal on a new factory trailer brake controller to fit a 2006 F250 Diesel Truck?
View 1 RepliesI have a 2014 F 450 and today one of my trailers will not engaged the brakes and it is saying on the display that there is no trailer connected. I cannot engage the brakes manually with switch.
I have running lights, I have brake lights I have hazards lights and turn signals. The brakeaway switch is not engaging the brakes when removed, I hooked up to another trailer of mine and it recognized and acknowledged being hooked to a trailer.
So... I know it is something with the trailer but what wire I should be looking at on the trailer?
So the other day 2/3/2014 my dad and I went out during the snow storm for the people that needed assistance. That day I pulled a 95' RWD dually with a 4 car open trailer and pushed 4 people from one location. Then after I went to assist the tractor trailer driver. My truck is a 2002 F250 super duty 5.4L with 4:10 gears. I got him unstuck then pulled him a 1/2 mile up a hill.
Pulling a stuck semi out of the snow - YouTube .....
2010 F250 Lariat, cab and a half, PSD. 5600 miles.
Sunday I started the pickup and received "trailer brake module fault" in the message center. I wasn't pulling so wasn't too concerned - hit the reset and continued on.
Sunday night I started the pickup again and received the same message followed by "check brake system". I also lost illuminated gear selection, the traction control active symbol was displayed and the traction control "off" (PB) was illuminated. After several attempts it reset, everything returned to normal and I was able to get home without incident.
Monday morning it wouldn't start. It indicated "trailer brake module fault", "check brake system", traction control active and off, no gear indication, the odometer indicated "-------" and it did not react to the key in the start position.
Tuesday morning I attempted to start and it was the same as the previous attempt. I noticed that the theft prevention appeared active (flashing) so I removed the key, locked the doors, unlocked the doors, tried again - no joy.
I kept trying while holding my mouth in different positions and finally by the grace of God it fired. I delivered it to the dealer.
The dealer called yesterday afternoon and reported that everything is a result of a bad trailer brake module. The new one is to arrive today, they will install and everything will be peachy.
I asked if they could just unplug it and reprogram the truck to believe it never had one - the service writer said it can't be done, different piece parts on trucks with or without trailer brakes.
I really have no choice but to push the "I believe" button and carry on but I am slightly concerned. The fact that the trailer brake module can cause catastrophic failure doesn't seem too cool, I don't have a real warm and fuzzy feeling associated with venturing far from pavement, reliable communication or alternative transportation.
In the meantime I suggest that no one take "trailer brake module failure" lightly.
My husband and I bought a 09 f-250 with 58000 miles. It used to pull our travel trailer with no power issues. Now the rpms go up & the power goes down. It never gets hot nor any lights come on. It's been in the shop twice. The first time nothing was found. The second time we were told it was dirty fuel filters. The truck only has 70k miles...
View 2 RepliesMy 99 f250 ran hot while towing my travel trailer when the fan clutch gave up. ever since iv been noticing coolant loss and pressure in the day tank.ive changed the water pump,radiator. day tank and cap plus the thermostat.
View 9 RepliesI have a 2006 f250 superduty crew cab longbed with the v10 gas motor. it has 201000 miles on it and towed great up until last month. I was towing a 5000lb trailer down the interstate at around 68mph,suddenly it was like the drive train disengaged and the motor had nothing left, check engine light on but no overheat condition or lack of oil pressure. we put a new fuel filter and pump on and maf, took trailer out again and same problem, pulled to the side and turned off, immediately restarted and ran fine. It has a cat not cleaning code in it now!
View 14 RepliesI have a 2006 F250 and my 7pin and 4 pin connectors are just hanging loose. I'm not sure what happened to the factory bracket. What is the part number for this bracket? Also, where does it mount to? I looked under the truck and couldnt tell where the factory one mounts.
View 4 RepliesOK....my gas cap (5.4 gasser) wasn't put on properly at the gas station. A couple of blocks later, the "Check Gas Cap" notice came on. I stopped a few blocks later, and installed the cap properly. The notice STILL came on. After messing with the cap 4 more times, I gave up, but the notice is still on. Do I need to have it "erased" like a code, or is there a problem with the cap? Everything LOOKS fine...
View 2 Replies1999 f250 5.4L... Its done this 3 or 4 times now. Driving and it starts pulling to the right pretty bad, almost like if the front passenger tire was messed up or something. Today it did it, after I let it sit for a few min, then drove back to the house, it drove straight. Also, when it pulls to the right, its very sluggish, as if I'm pulling a very heavy load. From a stop, it doesn't even go until I hit the gas, and at that its very sluggish, sorts feels like if you drive off and forget the ebrake is on.
Also I've noticed some burning on the passenger side which I've read is probably the head gasket. I can see the oil dripping on the exhaust, causing the smoke. Also, my CEL just came on, with code P0401 "powertrain exhaust gas recirculation flow insufficient detected". Recently changed the plugs because it was running and idling a little rough.
At this point in wondering if the pulling issue could be something with the brakes, when I'm driving, it sounds like something is rubbing, I haven't looked at the brakes yet but I'm likely going to do new pads and rotors all around soon anyways.
A buddy's 2012 f250 message center is not working at all. He replaced the fuse and it's still not working. The gauges work but not the high tech information center. He isn't sure if it's out of warranty because he can't see the miles. I'm not sure that's it's anywhere related but his back up sensors do not work either.
View 3 Replies