2014 F450. Front end and steering wheel shake violently when braking while towing a 20,000 pound trailer down a long and steep highway grade. It does not happen when towing my 12,000 pound trailer down the same highway. Could I be setting off the ABS braking system?
View 14 RepliesMy truck has had a bad vibration for some time know, it started around 41,000 miles and took it to my local Ford dealer... the told me I needed tires and that my airdam/bumper extinction was loose and causing it to vibrate . I put front tires on I fixed the plastic on the bumper and replaced steering stabilizer . Vibration continued to come and go after all of that so I replace the steering stabilizer with a different steering stabilizer .
I noticed that the front seals for my four-wheel-drive allowed the shaft to move up and down by more than a half an inch of play.so I had Ford replace the front hubs and seals . Vibration is now worse and more often. It happens every time I am between 50-54mph. I am going to put 6 new Michelin defender Tires on it and new shocks and a Monroe steering stabilizer.
YouTube....
I have a 2014 F 450 and today one of my trailers will not engaged the brakes and it is saying on the display that there is no trailer connected. I cannot engage the brakes manually with switch.
I have running lights, I have brake lights I have hazards lights and turn signals. The brakeaway switch is not engaging the brakes when removed, I hooked up to another trailer of mine and it recognized and acknowledged being hooked to a trailer.
So... I know it is something with the trailer but what wire I should be looking at on the trailer?
Im working on a 03 f-450 that has a front end vibration, it starts when you hit 25 mph and its a humming / vibration that seems more to the passenger side than the drivers side. You can also hear it decrease when you come down in speed and it dissappears below 25 mph. Its a 2003 F-450 CC 4x4 DRW with the v-10.
View 7 RepliesMy 2014 f250 4x4 crew cab with 6.2l gasser only gets about 7.5-8 mpg at 65 mph while pulling my 27' bumper pull travel trailer. I know that thing is basically a wall trapping the air but is there anything I can do to gain a couple mpg more? I can average about 15 mpg at 65 mph without the trailer on the highway.
View 14 RepliesHow do I get the front axles out of of the knuckle? It seems like the seals are holding them in? Is there any trick to to getting them out,I am trying to do my ball joints
View 1 RepliesTried converting the 10 lug to 8x6.5 and didn't work. so now i found a 2000 F450SD 8x225mm monotube front axle but just got my hands on a '99 F350 4.10 DRW axle 8x170mm....can I bolt the 8x170 hubs (spacers as its a dually front axle) up front? not sure if the bolt pattern on the rotor will work...
I was thinking adapters up front as i can widen the front track abit if i had to, but dont want to go 170mm to 225 adapters out back, as i think its too much weight for those... I will have a front 90 F-superduty 10 lug set up....
I've had the 450 a little over two years. Its used 95% of the time for hauling trailers, including the toy hauler. Has not given me a single problem since day one and now has around 21,000 on the odometer.
Lately I've noticed a "grinding" sound coming from the front end somewhere. It is most apparent when I'm turning at slow speeds; especially left. To describe it would be similar to worn out brake pads or maybe a wheel bearing going bad. It does it whether I'm on the brakes or not.
I thought there was a v10 specific superduty section like how the psd does, but my thread went in the "performance, engine, troubleshooting" section.
I wanted more exposure than that particular small viewed area.
I don't have a video of the noise, but my 99 f450 v10 5spd has some iffy noise coming from the front. I've read so many threads on this and they either end with "my motor had 1-2-3 bad pistons" or "my flexplate was cracked" and all that dealt with chain tensioners were never finished.
I know what piston slap sounds like (worked on many cobras and lightnings with forged pistons that had it) and have experience with bad wrist pins and broken piston skirts, and this noise doesn't sound like any of it.
Noise is a loud clicking/clunking/Detroit diesel idle noise. When you rev the engine up it doesn't lighten or get better, only worse as rpm goes up. Oil is terrible looking, I'll be getting that changed this week.
Story on truck. I've had this thing for 4 years with blown motor. I got a buddy that acquired a parts truck and he said it ran good. I dropped my truck off and he swapped the engine. I got my truck back running, but with this engine noise. He said it needs to get run some more and change oil.
I think it's timing tensioners, my buddy says it will come out of it, a mechanic friend says it's going to blow up "because they all do" and I don't really want to replace the engine again.
If it's tensioners, how big of a job is it. I have the cam clamps and crank stop and the ford tools to make sure crank and cams don't rotate while apart.
I'm just 650 miles from my truck and may need someone else to do the work. Which sucks.
I have 2009 F-450 6.4L Diesel with 41K miles and just started to have a noise that can be heard up in the CAB of the truck while driving or idling. It sounds like a dry ball bearing that would go bad in home computer AC power supply or CPU cooling fan. The sound starts when the engine is at full operating temperature and most noticeable and the loudest if you are standing in front of the engine at idle outside.
Checked all fluids and they are normal. Turning the steering wheel doesn't affect the sound either or turning off the AC. Check engine light has not come on. The only thing I have noticed is that clutch fan stays on a very long time after starting cold and takes about a mile or two before it disengages. The truck is only used to tow a 36' 5th wheel and sits the majority of the time.
.I just changed out all the steering linkages due to a lot of slop and worn out tie rod ends. This problem existed before I changed them but I thought for sure changing the linkages would fix it. When I brake hard my front tires wobble very bad. I haven't ever experienced the death wobble that is common in these trucks, but the symptoms seem the same, its just only when I brake hard. I can look at my front left tire while braking hard and see it wobbling. The wheel bearings and ball joints only have about 15k miles on them. I can't tell if the front wheels are moving independent of each other back and forth, or if they are both shaking back and forth together. What might cause this? it's a super uneasy feeling when it happens, especially because whenever you are braking hard there is usually a reason.
View 14 RepliesWhen braking the truck shakes terribly, enough to toss a drink out of the cup holder almost. Sometimes there is a slight feeling in the peddle but not always. The shudder feels like it is timed with each revolution of the wheels.
It developed from a perfectly stopping truck over the course of maybe a month. I don't drive the truck that much either.
Things I have checked:
1, all u-joints, they all look and feel good, no play or slop in them
2, air pressure in all tires, even rotated them, no effect
3, brakes-front and back all looked good but I went ahead and replaced front pads and rotors, cleaned caliper pins, zero effect.
4, shudder exists whether in gear and slowing or in neutral, 2wd and 4wd
What the heck else is there to check? My first thought was, front brakes/warped rotors, but after pulling them apart there was so much life left on the rotors and pads and replacing all that with new did nothing! Could bad back brakes cause this much of a shudder? They look fine as well.
Problem: 55-60+ mph hit a bump front end shakes violently. Slow down to 40 mph it stops. DOES NOT happen every time, and may only happen once a week, but when it does my whole front end feels like it will come loose.
Solutions to date that have not worked:
1. Rotate and balance tires. (tire shop)
2. New shocks. (me)
3. New steering stabilizer. (me)
4. Changed ball joint and bushing in track bar. (Dealership)
5. Check ball bearings and seem to be ok. (me)
6. Check tie rod ends and are ok. (Dealership)
The only other options people have given me:
1. Dual Steering Stabilizer. (Have had truck since Jan and hasn't done it in about 19,000 miles. Why would it need it now? Truck has 109,000 miles on it.)
2. New tires. (If it were the tires wouldn't it do it all the time? )
I have an 03 F350 4x4 dually. Was pulling hard left at low speed when braking (front). Replaced pads, calipers, rotors, hoses and tires. Still the same problem. You can feel the abs activate right before it almost locks up the left front brake (basically will pull the steering wheel out of my hand). BTW the abs light does not come on.
View 2 RepliesI'm having trouble finding the source of a vibration in the front end if my 1999 f350 super duty 4x4. The vibration is felt all the time but worse when under 40mph, while braking, and especially when turning.
I have replaced the rotors and brakes, tie rods and Drag links since the issue started but no change. In the vibration. What should I check next?
2008 F250 Crew Cab 5.4, 79K miles, had new brake pads installed at 40K miles. Recently, I noticed front end shudder and some pedal pulsation while braking. It started kind of sudden. My first thought was a warped rotor.
When I took things apart, I found passenger side front rotor was cracked and the caliper pistons were rusted and falling apart, the old pads were only worn about half way. My thoughts on a bad rotor were confirmed, and then some.
I replaced the broken caliper, both front rotors, installed new pads on all four wheels, and bled the brakes. To my surprise, the brake shuddering did not go away. I'm stumped.
I have a 1999 F450 that was bought new as a cab and chassis. The truck belonged to my dad who passed away two years ago and now I have it. I am wondering if it has 4.30 or 4.88 gears. The rear end is huge! It has an aluminum cover with cooling fins on it, not sure if they both had that or not. I looked online and I think it said all cab and chassis had 4.88?
View 10 RepliesMy 99 f450 7.3 runs bad on first start of day. I checked the codes 3 codes p0475, p0470 and p1247. Now here is what I tried I plugged it in over night and it will start and run as should the next morning with out side temp 47. Drove the truck late yesterday evening didn't plug up tried it this morning with a outside temp of 47 truck starts but missing and like of power. My problem seems to be temp related. Will low boost pressure cause this problem what do I need to do?
View 4 RepliesPurchased new 2016 450 platinum. Has less than 800 miles on it and has a terrible vibration between 70-80 mph... Already have taken to dealer who stated there was a wheel out of balance and that they fixed the issue. But still present.
View 14 RepliesI have a 99 F450. I have an ABS light on. No codes (at least not that my code reader can pickup), but I am also not having any issues. Brakes work fine. What to swap out or where to look?
View 7 RepliesCan an f-450 with a blown 6.4 diesel received an transplant from an f-350 V-10.
How much would need to go over from the f-350 to f-450?