Ford Super Duty (1999-2016) :: 2009 F450 - Dry Ball Bearing Sound From Front Of Engine
Jan 6, 2017
I have 2009 F-450 6.4L Diesel with 41K miles and just started to have a noise that can be heard up in the CAB of the truck while driving or idling. It sounds like a dry ball bearing that would go bad in home computer AC power supply or CPU cooling fan. The sound starts when the engine is at full operating temperature and most noticeable and the loudest if you are standing in front of the engine at idle outside.
Checked all fluids and they are normal. Turning the steering wheel doesn't affect the sound either or turning off the AC. Check engine light has not come on. The only thing I have noticed is that clutch fan stays on a very long time after starting cold and takes about a mile or two before it disengages. The truck is only used to tow a 36' 5th wheel and sits the majority of the time.
View 2 Replies
Advertisement
Im working on a 03 f-450 that has a front end vibration, it starts when you hit 25 mph and its a humming / vibration that seems more to the passenger side than the drivers side. You can also hear it decrease when you come down in speed and it dissappears below 25 mph. Its a 2003 F-450 CC 4x4 DRW with the v-10.
View 7 Replies
I have a H&S mini max. Controller and have installed the mild download and run on the street setting for every day and tow setting while towing my fithwheel, when I just took it out for a test drive towing the fit wheel going up hill it kept shifting up and down which sure felt like 3rd and 5th because rpm would go from about 3500 to 1500 back and forth so it sure felt like it was not hitting 4th, could this be a controller issue?
View 4 Replies
How do I get the front axles out of of the knuckle? It seems like the seals are holding them in? Is there any trick to to getting them out,I am trying to do my ball joints
View 1 Replies
Tried converting the 10 lug to 8x6.5 and didn't work. so now i found a 2000 F450SD 8x225mm monotube front axle but just got my hands on a '99 F350 4.10 DRW axle 8x170mm....can I bolt the 8x170 hubs (spacers as its a dually front axle) up front? not sure if the bolt pattern on the rotor will work...
I was thinking adapters up front as i can widen the front track abit if i had to, but dont want to go 170mm to 225 adapters out back, as i think its too much weight for those... I will have a front 90 F-superduty 10 lug set up....
View 1 Replies
I've had the 450 a little over two years. Its used 95% of the time for hauling trailers, including the toy hauler. Has not given me a single problem since day one and now has around 21,000 on the odometer.
Lately I've noticed a "grinding" sound coming from the front end somewhere. It is most apparent when I'm turning at slow speeds; especially left. To describe it would be similar to worn out brake pads or maybe a wheel bearing going bad. It does it whether I'm on the brakes or not.
View 14 Replies
I have a 2003 Ford F450 super duty xl. At first there was a loud clicking sound coming from under my dash. I charged the battery up and the sound went away but the truck will fire up but not turn over and start. I thought maybe it could be the relays but the clicking sound quit.
View 2 Replies
2014 F450. Front end and steering wheel shake violently when braking while towing a 20,000 pound trailer down a long and steep highway grade. It does not happen when towing my 12,000 pound trailer down the same highway. Could I be setting off the ABS braking system?
View 14 Replies
I thought there was a v10 specific superduty section like how the psd does, but my thread went in the "performance, engine, troubleshooting" section.
I wanted more exposure than that particular small viewed area.
I don't have a video of the noise, but my 99 f450 v10 5spd has some iffy noise coming from the front. I've read so many threads on this and they either end with "my motor had 1-2-3 bad pistons" or "my flexplate was cracked" and all that dealt with chain tensioners were never finished.
I know what piston slap sounds like (worked on many cobras and lightnings with forged pistons that had it) and have experience with bad wrist pins and broken piston skirts, and this noise doesn't sound like any of it.
Noise is a loud clicking/clunking/Detroit diesel idle noise. When you rev the engine up it doesn't lighten or get better, only worse as rpm goes up. Oil is terrible looking, I'll be getting that changed this week.
Story on truck. I've had this thing for 4 years with blown motor. I got a buddy that acquired a parts truck and he said it ran good. I dropped my truck off and he swapped the engine. I got my truck back running, but with this engine noise. He said it needs to get run some more and change oil.
I think it's timing tensioners, my buddy says it will come out of it, a mechanic friend says it's going to blow up "because they all do" and I don't really want to replace the engine again.
If it's tensioners, how big of a job is it. I have the cam clamps and crank stop and the ford tools to make sure crank and cams don't rotate while apart.
I'm just 650 miles from my truck and may need someone else to do the work. Which sucks.
View 4 Replies
I am replacing the ball joints on my 07 f250 4x4. got down to the removal of the shaft itself and it won't budge. What is the secret here. Have to go to work on monday, and the weather in Cleveland isn't going to be very good on Sunday.
View 10 Replies
Ive got a 2002 f250 Sd 4x4 with 93000. Im getting severe vibration from the front drivers side at highway speed. I thought it might be a warped rotor but i cant feel it in the brake pedal, when I put the brakes on. How can you tell when the hub bearing assembly is going bad? The truck doesnt pull to that side either. I can hear it, and feel it more when i'm going around highway corners. When im driving through town, I can hear a "clunk,clunk,clunk" noise coming from that side also.
View 14 Replies
2001 F450/6.8 gasser. Auto trans. This strange thing just appeared from nowhere. Start the truck, put it gear. As soon as the truck starts to roll, the chime begins to sound. If I continue on, it'll beep 80 or 90 times before stopping. As soon as brakes are applied and the wheels stop turning, chime disappears. Happens in forward or reverse. No lights appear in the cluster. A check with an Actron scanner shows no codes or MIL. Seat belts are buckled.
View 4 Replies
I turn off the key and remove it. The engine shuts down but everything else stays on, the radio, heater fan, etc. I tried to search the forum but couldn't find anything about this problem. I'm guessing there is a stuck relay or a bad ignition switch.
2000 F450 7.3 PSD automatic 4X4
View 7 Replies
I have read the older posts here on the super duty ford 4x4 system. At 60,000 miles I noticed what sounds like a gear or bearing noise, or even a whining noise like you would hear from mud grip tires, coming from the front end area, while driving back from Kentucky to Georgia. I have quiet running street tires on this pickup.
I have a 2004 F350 crew cab XL, automatic, 4x4, limited slip axles, 430 gearing and a V10. This truck has always been extremely quiet on the highway. This noise I described above has increased and the truck now has 70,000 miles. I have the factory 4x4 dash switch in my truck cab for the 4x4 engagement. I always thought the dash switch engaged and disengaged the transfer case, and locked or unlocked the automatic hubs.
The service guy at the dealer now tells me that the dash switch only locks and unlocks the front hubs, and the front drive shaft and front differential are engaged full time. So, after checking my tires for defects, and for any play or bearing noise in my wheel bearings, I am looking at pulling the drive shaft out keep the front differential from turning, to determine if I have a bad bearing in the front axle assembly.
Now I read some of the posts here, and they say that with the dash switch in "2 wheel drive", the transfer case should be disengaged and the front drive shaft and front axle should not be turning at all. What is turning up front with the 4x4 disengaged on the dash switch ? I'm afraid to drive my truck out of town now and I need to isolate this issue and get it repaired. This has been a great truck and it's very reliable.
View 10 Replies
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
View 11 Replies
I own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 Replies
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 Replies
I have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 Replies
Well, I've been meaning to get to servicing/re-greasing the front hubs/bearings for a while but somehow it keeps getting moved down the list.
2000 F250SD 4X4 Gas Manual Hubs+Trans
I'm currently going through the many threads that turned up in my search query.
Driving slow with the windows down it seems like a low whine or squeal coming from the left front. Tone changes when working the steering wheel left and right. Haven't detected any grinding sounds. Any other techniques for isolating the problem? It's going up on jack stands tonight and I'm going to see if there is any wobble from the front wheels and I'll listen as I turn each of the front wheels. Oddly, the right front hub is hard to turn. Left front turns easy.
Viewed Rob259956's videos on servicing the hubs. Currently researching accessing the wheel bearings. It seems pretty straightforward. Truck has been off road but not mud bogged or anything like that. I'm guessing a bad bearing will be easy to identify as will a bad o-ring but any other stuff I should look closely at?
View 6 Replies
I have a 2003 F350 srw 6.0. 4x4. Front driver side wheel bearing went out. Went to the auto parts store got a replacement. Got it all tore apart, put the new one on and the lockout didn't seem to fit right. Is there a difference in wheel bearing assemblies for electronic shift on the fly and regular lockout? I have the electronic shift on the fly lockouts and it had just a little bit of play in it when I put the snap ring back in.
View 3 Replies
I am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 Replies
