Ford Super Duty (1999-2016) :: F250 - Front Turn Signals Not Working
Mar 21, 2014
1999 F250 super duty. I am having a problem with the front right turn signal not working. The indicator on the dash also does not work but I can hear the relay clicking double time and the rear signal works. I have changed the bulb and fuses and went under the dash and the column to be sure a connection had not come loose. I have looked through the forums to try and find an answer with no luck. What to try next?
View 4 Replies
Advertisement
I have a 2002 F250, 5.4 extended cab 4x4. Factory lights. I have no turn signals. They were working just fine and without turning off the truck, all 4 corners quit working at the same time, as far as I know. The indicator lights on the instrument cluster don't work. I have checked/replaced all fuses. Replaced the switch lever and the blinker relay behind the dash. The hazards do work and always have. It might be coincidence but I believe the back-up lights quit working at the same time.
View 2 Replies
I have a 2000 f250 with auto/manual locking hubs and today the 4x4 quit working. The light comes on the dash and the drive shaft and u joints turn but the front wheels don't turn even when its locked in. I assume its the hubs? And when I am going down the highway about 75 the front starts making a hellacious noise but stops if I slow down is this connected?
View 11 Replies
Coming back from a trip I got a e-brake light show up on the dash then noticed the signals stopped working and the heated seats no longer turn on. I scanned it with my AE and got a brake fluid sensor error come up but nothing about the signals .... is this a common problem or is there a connection between all this? 2003 F350 6.0L .....
View 2 Replies
I own a 1999 F350 CC SRW w/ 7.3L PSD engine. My turn signals stopped working suddenly. I've checked the fuse panel under the dash but it doesn't show any fuse for the turn signals.
My hazards do work although I noticed something very strange. When I tilt the steering column down the hazards stop working and when I tilt the column all the way up they work again. Still no turn signals though.
View 1 Replies
2000 V10 F250 - daughter is using my truck and called to tell me the turn signals weren't working. She called me shortly after and said she adjusted the tilt and hazard lights came on and now she can't turn them off. I had her pull the hazard fuse to stop them. She then noticed the brake light weren't working. I don't know if the brake lights were because she pulled the fuse or she just noticed they weren't working.
A week or two ago, she said she parked the truck, turned it off and took the keys. When she came back out, the truck had rolled across the street. Periodically, over the years, I would go to start the truck and nothing happened. I would shift the gear selector in and out of drive. Then the truck started.
Finally, since I've owned the truck, the when I activated the left turn signal, the selector frequently wouldn't stay "locked" till I turned. So, are these related? Do I have multiple issues going on in the steering column. Where to start looking when she gets the truck home?
View 3 Replies
I'm having problems with my front marker lights. The turn signals work but when I turn on the parking lights or headlights they don't work. They only work with the turn signals. And I can't get the front side marker lights to come on. I've tried everything...
View 2 Replies
I have a 2004 350. Turn signals quit working don't come up on dash either but when I turn the flashers on the left turn signal on come on that's on the dash and the lights. I replaced the turn signal relay that's under the radio. The old one would buzz when I turned the turn signal on but nothing would come up the new one clicks as it should but I'm still not getting turn signals lights on dash nor the light it's self. The flasher is still like it was only the left one comes on.
View 1 Replies
I have a 2006 F250 Superduty 4x4 that the brake lights hazards and turn signals have stopped working in the rear.. The middle cab brake light does not work either.. The running lights do work as well as the turn signal and all lights in the front.. I also checked the trailer plugs and both work for running brake and signal lights.. I have checked all fuses under the hood as well under the dash with a test light and i have nothing blown.. I have replaced the Brake switch as well as the flasher module under the dash and picked up a new multifunction switch (Turn signal/hazard) and that didn't work either.. I'm stumped at this point.. I have not checked the bulbs yet but wouldn't think they would all blow at the same time.. (will do this next)..
View 3 Replies
I have a 1995 Ford f250 Powerstroke and i do not have turn signals, rear running lights, brake lights or reverse lights. i checked the fuses and they seem to be good but i dont want to tear everything out to check the harness if it could be a bad ground. any insight?
View 1 Replies
Recently, I lost function of brake lights, turn signals, and hazard flashers. All happened at the same time. Some threads discuss flasher relays, short steering column wiring (position of steering wheel), and fuse failures.
I checked #18 fuse and a few others. All had continuity. I assumed my bulbs were all good. My hazard push-pull switch did not feel right. There didn't seem to be engagement. At this point, there was a good chance that the multi-function column switch had failed so I decided to try replacing it. I'm happy to report that this switch was the cause of all the light function failures and now, all is well again.
Removal is done by prying the key lock switch cover off,, removing three 1" Philips head screws that attach the lower column shield to the upper shield. At that point the upper shield can be completely removed. The lower shield was not totally removed because the tilt lever was left on. The switch is attached to the column with two 3/4" Torx 20 fasteners. The upper is easily accessible and the lower fastener can be removed by pulling the lower column shield down so access can be achieved. The two wiring harnesses have a conventional harness lock to depress and the connectors pull outward from the switch. Installation is the reverse of removal, noting the dowel locator and small plastic dowel on the lower shield.
View 1 Replies
I just got a 2000 F350 cc drw 7.3l.
I did search but have had no luck. My turn signals do not work, unless my foot is on the brake pedal my green arrow indicator wont even turn on. When they do my bulbs work but don't cycle so I know all the bulbs are good as I had my wife check all four corners when I got them to come on for a split second. I have tried replacing the MFS and the turn signal relay under the radio in the dash.... When I do turn on my blinkers I can hear the relay click once but that is it, no more.
I tried checking the wiring in the column and tilting the column to its extremes while trying to engage the turn signals. Also, if I unplug the brake light switch then I do not get an arrow on the IC to light up so I am guessing the power flows through that switch. I don't have a chilton manual yet and the owners manual was not in the truck. I did check fuse 23 ?
View 2 Replies
2007 F250 4WD 5.4l ... when I turn sharply in either direction I am getting a light clunk sound similar to when you are in 4WD on blacktop and try turning. The engine also seems to wanna stall when I cut the wheel too sharp.
View 4 Replies
I just bought a 2001 F250 XLT and it came with the standard power paddle mirrors. I would love to add the towing mirrors (preferably heated with signals), but what I am wondering is if the connectors for the mirrors are the same. Also would my truck that came with the standard paddle mirrors be wired for turn signals and heated options? How would I test for this? Also do all XLT's come prewired for the hardwire keyless entry pad if they have keyless entry?
View 1 Replies
I have a f 550 that blew out starter cyl on inner fender.and starter, replaced both. Now I have no brake lights or 4 ways and no turn signals....
View 4 Replies
Yesterday I was parked on an incline with my front wheels on gravel and the rear wheels on wet grass/mud. When I tried to go, the rear wheels started spinning. I then switched on the low 4x4, and tried to go. The rear wheels continued to spin, but the front did not turn. I had new wheels installed, that has a cap that covers the manual locking hub, so I couldn't turn it to lock the hub. What should I look for to fix the problem?
2007 F250 4X4 Larriat SRW
View 2 Replies
So I shorted wires out putting a new plug on my mirror, and now I have no turn signals, no backup lights and no overhead display that shows mpg and outside temp. All fuses are good, and I don't think it is my flasher relay just because I also have no park lamps or over head display.
View 3 Replies
only have clearance lights at plug no output for brake and turn signals
View 1 Replies
I got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 Replies
2005 F350 Super Duty. I have no brake lights turn signals or hazards. dealer suggested the multiswitch but changed it and still not working?
View 2 Replies
I have a 2006 F350, it keeps blowing fuses for the brake/turn signals. The puzzling​ part is it only does this when the truck is running.
View 2 Replies
