Ford Super Duty (1999-2016) :: Hard Shifting - Slight Bit Of Clinking Noises Every Time Started From A Stop
Apr 26, 2017
Well shoot, not even 120k on the odo and I've had my first major problem with the truck, and the one thing I hoped wouldn't be an issue, especially since I don't work my truck hard and 95% is driving unloaded highway as a daily driver.
Last time I drove it coming home from grocery store there was a big racket from down under (transmission area). It instantly didnt feel right - there was a slight drag even when the clutch was in, but rolled fine when I pulled it out of gear entirely. Was VERY difficult to go into first gear. Other gears shifted ok but some of them felt hard too. Would not go into reverse at all!. Slight bit of clinking noises every time I started from a stop, but made it home ok and things seemed to ease up as I went. Today, seems to be shifting fine, reverse works and everything.
Now for several years I've had a noise that I couldn't figure out. I am guessing it's related because it sounded like was coming from tranny area. Often, when starting out from a stop, there was a bit of clinking noise like a couple tin pie pans rattling together just as the clutch started to go. I kept thinking it was loose heat shield or something clanking just under the initial vibration of getting going. Never did find anything loose. I'm guessing it's internal.
I've called a couple local shops and so far no one wants to mess with it. Dam this sucks i hoped the MT would be more reliable, not the first thing to go. I myself have never messed with any aspect of a transmission, though I not opposed to learn however I was hoping to take this on an out of state trip end of May, and I'm not going to have much any free time between now and then.
View 9 Replies
Advertisement
The truck is in my Sig 01 F250 5.4
Just got back from a long trip with it. Parked it for 3 days, all was running fine. Went to dinner Sat night and all was great, left the restaurant and as soon as I started the engine I noticed a slight vibration. As soon as I hit 42 miles per hour, it started shaking pretty good. I pulled over and checked under the truck to make sure I did not have anything I was not supposed to hanging down.
Driveshaft looked good, nothing leaking from rear end or tranny. When it does vibrate, the Tach shows the unhappiness as well. This a.m. driving to work it was vibrating at all speeds and shifting was very rough, had a hard time deciding if it wanted to be in second or third gear. I don't think this is drive train issue... When it shutters and sputters at 40ish MPH, its almost like it loses power and I have to let off the gas. and then under power it shakes badly.
I had the super chip settings for performance tow when this started and then I changed it back to stock settings, thinking it might work, which it only got worse. Changing the settings with the Superchip you have to disable the fuel system and I do this by pulling the fuel pump fuse under the hood in the power distro box.
I think the ujoints are still good, the oil and tranny fluid are spot on. Hubs are locked but in 2WD. Had all the front end replaced 15K miles ago. Brand new tires and wheels in Sept, front end alignment done at same time, front brakes were 90% and rear brakes at 20%.
View 10 Replies
So a few months ago I would occasionally hear what appeared to be a slight squealing noise from a pulley when I started my truck. It was very intermittent, so I didn't think much of it.
After a few weeks, I realized I was only hearing it on colder mornings - it would also go away rather quickly. I bought a mechanic's stethoscope, and figured I'd get to it on a slow day.
Today, I finally broke out the scope and tried to figure out the source. Didn't really find any pulleys making noise, and I did notice that when I shut the truck off, it squeaks for a second or two as it comes to a complete stop.
My dream of finding a bad pulley or perhaps a power steering pump was crushed. I had hoped to do a little Easter wrenching and put this noise to rest. So, I did what any good mechanic would do - I Googled the issue.
I'm reading that it could be the belt. Certainly wouldn't bother me too much as that is an easy fix. The belt isn't too old - about 4 years and 20 - 30K on it.
I took a few pics of the belt and can take a video of start/stop ....
View 7 Replies
The tranny is shifting really hard between 2 and 3 if I feather the throttle it can be a little less of a jolt but still enough none the less iv never done a filter and fluid change as I just got it it has 235000 miles 99 v10 super duty 4x4....
View 8 Replies
Recently I have had an issue with my auto which was just rebuilt. About 500 kays after i picked it up it shifts dangerously hard and immediately into all gears at around 20-40 mph, converter also locks immediately. The speed sensor in the box was replaced with the rebuild but I'm having it replaced again this thursday just in case.
Just for the record I cooked it on the beach a while back, the speed sensor was replaced with the rebuild as it was doing the above, the od light also flashes when this occurs, before and after the rebuild.
Prior to cooking it never had an issue.
What could be causing it? I'm starting to worry it cant be fixed, have done a google and tried a couple of things mentioned. Code says wiring issue associated with speed sensor in box.
View 8 Replies
I recently bought a van that has a hard shift problem. It is a 1995 E350 with a diesel. If I take off from a stop without babying the throttle, the shift from first to second is very hard. Second to third is hard but not as violent. What might be happening?
View 9 Replies
I have a 1997 f-250 heavy duty with the 7.3 I have been having problems with very aggressive and hard shifting. While it is acting up the overdrive light on the shifter blinks. This problem goes away and it might be good for a month or so, But it always comes back. I have had it to a professional trans tech, He replaced a part on the side of the tranny. I thought it was fixed, But now it is acting up again.
View 4 Replies
I have a 2002 ford f250 with the 7.3l diesel. I recently installed a ts performance chip. On my pcm. And after i first tried all the different stages I didn't like how my transmission was shifting hard. So I contacted the manufacturer and he told me they could reprogram the chip for smoother shifting. So I removed the pcm and removed the chip. But when I went to reinstall the pcm I bent one of the pins on the pcm some how.
So I took it back out and straightened the pin with pliers . i reinstalled it back in the truck. Only to find when I reattached the battery cable I have no power to anything ignition ,horn, lights,Cigarette lighter etc. So my question is if the pcm is bad, or not contacting properly due to the pin being messed up. would that have anything to do with the lights and horn and all that? I suspect its the gem bsm or Vsm. Whichever one my truck has. But really not sure because everything worked fine just 20 min b4.
View 1 Replies
I have a 2011 F-350 6.2L that has extremely hard shifts from 3 to 4 going up and 2 to 1 going down. Sometimes on downshifts it feels like something has ran into the back of the truck. I had the computer updated when the truck had approximately 40,000 miles on it and he assisted a little bit. The truck now has 140,000 miles and it is back to shifting horribly. I put it in the shop at the dealer on 30 December 2013. The dealer says that the problem is that the shift solenoids need to be replaced but that they are not available. The truck is still sitting at the dealer and I am being told that the parts should be available mid February.
View 10 Replies
I have been having hard shifting from 1st-2nd when cold. Rpms up to 2000 and let off then goes into 2nd. After that, she shifts fine and shifts well until next morning when she sits overnight. Build tag is August 09, 2001, so no old mechanical diode? Took a sample of fluid and it is dark red (pic attached) and smells like hydraulic fluid...I don't think it smells burned. Does it sound like the calve body 1-2 shift or solenoid pack or needing rebuild?
View 3 Replies
So I have a 1995 f-250 4x4 with the 460 and a E4od. So when I bought the truck I drive it two hours home and when I got into town it started shifting really hard and searching for gears. So I flushed it and installed a new oil filter because the oil in it was brown. Very brown. And smelled awful. So it shifts good, but what's happening now is that it shifts good in drive when it wants to.
In the morning it works great but when I get in it to leave after school it shifts really late (around 2900 rpm) and hard. So I put it in first and then into second but when it's time for third and I put it in drive it shifts back to first. But if I stop shut it off for a few minutes and turn it back on it works fine. It only does this after it's been sitting in the school parking lot all day. I replaced the mlps but not the connector due to I didn't have time at the moment. Could it be the tps? Something mechanical?
View 4 Replies
2002 5.4 super duty. My truck had started to ping, and knock worse over time. I did some research on this site, and I decided to remove my K&N air filter. Replace it with a traditional paper filter. Then I cleaned my mass air flow sensor. The results were great, no more knock and ping.I will check the MPG next to see if I get any improvements.
View 1 Replies
2006 E-350 Dually Ambulance Chassis with the 6.0... Approx 125000 miles.
Recently, the truck started an issue. its an every once in awhile thing but has been doing it more recently. The OD light will start flashing and the vehicle will start to have clunking in the tranny and start shifting rough. ABS kicks in making it hard to stop. Once you turn the truck off and back on, Its fine until it does it again. Im connecting to a scanner tomorrow to see if i get any codes.
View 14 Replies
My buddy's 2001 7.3L F350 has had 3 transmissions. Rebuilt and used. Once the new trans is in he goes like 15 miles and then is starts shifting hard and grinding gears. What this could be?
View 8 Replies
Just got the transmission rebuilt in my truck and other then shifting hard sometimes it has been doing great, Hooked it up to the goose neck this evening and everything was fine then went to back it up and pull it forward and after a short distance the od light was flashing and when i ran a check on it it was p0720? The transmission has less then 1000 miles on it?!?!? 1999 Ford F-250 7.3 Automatic....
View 5 Replies
I have a 97 F350 5.8 with E40D trans. I bought the truck with it shifting hard thinking maybe a simple filter/fluid change would fix it. It may have worked a little but did not fix the issue. There were 3 or 4 codes that I have already cleared up with new parts. I am still getting a 327 (something with EGR?) and 629 (Converter clutch control circuit failure). These show up in KOEO and KOER self test. The O/D does not flash ( bulb does work).
Parts that have been replaced: VSS, MLPS, new connector going into solenoid pack (tabs were broken), TPS. Removed the trans wiring harness and there is no damage or loose connections. When I replaced the solenoid connector I noticed there was some trans fluid in the connection. I cleaned it the best I could and reinstalled with dielectric grease.
The truck runs fine and shifts in and out of every gear fine its just shifting hard. If I unhooked the battery it will shift perfect for 5-10 minutes but then the hard shifting returns.
The only other thing I can find with my research is maybe the solenoid pack needs replaced. I figured if I take it somewhere they are going to want to rebuild/replace transmission. It seems like it can't be something very major since it will shift fine when reset...
View 4 Replies
So, in my 99 Bounder RV (F53 chassis), V10
I think it has a 4R100 transmission in it (I have not verified this).
I had the oil and filter changed about 10K ago.
Runs and shifts fine .... then I stop and idle with it in gear (say stopped in traffic for a few minutes).
Now the thing shifts super hard! I actually get rubber in all gears.
So I pull over, shut it off. Restart the unit and everything is fine again.
It does this very consistently!
I went to the local transmission shop. They said with 110K in an RV it could be anything and I should think about letting them rebuild it.
Now that is something I would do ... not diagnose a problem and just rebuild it. I thought a "professional" would actually look for the problem first.
I don't want to rebuild the transmission if there is small item that will fix this.
View 3 Replies
I started up the truck. It cranked perfectly as always. Was half way out of the parking lot going give mph and a warning beeping started with a message "stop vehicle safely". I did and the engine died. When I try to crank it it will not turn over at all. No power to engine at all.
View 5 Replies
Having a problem with calipers again/still seems like always. Replaced all calipers twice in 86K miles on a 2000 f250 crew 4x4 because of stuck calipers. Replaced brake hoses and all hard lines in the rear about 2 years ago. My problem now is the left front caliper is not squeezing hard enough to stop the truck evenly. (pulls to the right) The rotor had some rust from sitting and after driving a for a while the rust is not completely gone as you would expect. Replaced caliper bled a couple of times. Caliper looks to be getting pressure enough to bleed and can see it move when brakes applied when engine not running. I don't have experience with Proportioning Valves but do you think that is the problem and how do I fix it?
View 8 Replies
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 Replies
While in Tow/Haul with my 5th wheel when slowing down probably at 5 or 10 mph the last downshift is very hard and the brake pedal gets real soft until full stop. Afterwards the brake pedal is firm. Tow/Haul without the trailer is fine. It's an '06 F250 Supercrew 4x4.
View 6 Replies
