Ford Super Duty (1999-2016) :: Left Front Caliper Is Not Squeezing Hard Enough To Stop The Truck Evenly
Aug 6, 2014
Having a problem with calipers again/still seems like always. Replaced all calipers twice in 86K miles on a 2000 f250 crew 4x4 because of stuck calipers. Replaced brake hoses and all hard lines in the rear about 2 years ago. My problem now is the left front caliper is not squeezing hard enough to stop the truck evenly. (pulls to the right) The rotor had some rust from sitting and after driving a for a while the rust is not completely gone as you would expect. Replaced caliper bled a couple of times. Caliper looks to be getting pressure enough to bleed and can see it move when brakes applied when engine not running. I don't have experience with Proportioning Valves but do you think that is the problem and how do I fix it?
View 8 Replies
Advertisement
1999 F350 4x4 dually. Replacing brakes front and back. Rotors, Pads, and hoses. On the left front put rotor back on and torqued down hub nuts on rotor. Then caliper mounting bracket wouldn't fit back between mounting bracket and rotor. Loosened the hub nuts on rotor, and fit mounting bracket in place. Then torqued down the hub nuts again, and rotor rubs on mounting bracket and rotor/hub won't turn.
View 2 Replies
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 Replies
I have for the 4th time in a little over a year developed another issue with a rear caliper hanging up last year i ended up replacing both rear calipers with reman. from NAPA. 3 months ago i had to replace the right rear again. Now currently i am having the left rear starting to hang up again. I've done a fluid flush and everything. I'm kind of at a loss. I don't normally have this much trouble with brakes. Some of the symptoms that go along with this are a spongy pedal and inconsistent brake feel just like when you have air in a line.
View 1 Replies
Two weeks ago did a road trip to NH from RI and i heard a slight dragging only at low speed (10-15mph) in my left rear tire. figured the caliber was dragging a little, it was. Before arriving in NH the brake light came on. Long story short i get back to RI and the left side noise gets worse and starts to lock up. I finally replace the rotor which was warped, pads, and caliper which was bad.
Was driving it same day and still here the same dragging and screeching noise and the brake light is still on. On my way home the left side locked up at low speed without hitting breaks and slid the truck, mid you all parts are new on that side. I am not sure what it could be at this point something in side the axle?
View 2 Replies
I just hit a pothole on my way home just now and now my front right caliper is sticking. It happen about 10min from my house. As soon as i hit the pothole I can feel my truck pulling to the right and felt like there was some resistance when i was driving. I got home and peeked my head in the wheel-well and i can smell the brakes burning and smoking a little. How would hitting a pothole cause a caliper to stick. Is there anyway to unstick it or am i gonna have to change that caliper out...
View 8 Replies
Is this repairable or would it be better to just replace it ? Ive never rebuilt one of these.
View 11 Replies
I read a reference to the front brake caliper bracket bolts being one time use torque to yield and must be replaced every time they are loosened. Is this true?
This is on my 06 F-350 in my Sig.
View 3 Replies
2001 F250 SD diesel. Brakes have been working fine with no pulling. They just started to squeal recently so I knew it was time for some new pads.
I'm having a problem that seems to plague me often when I try to replace disc brake pads. I can't get the twin pistons to go back in to allow room to get the new, thicker pads in.
I unscrewed the cap to the master cylinder and used a spreading tool (that came in a brake kit from Advance Auto Parts) to compress the pistons. No movement.
I put a lot of force on it. No piston movement.
I unscrewed the bleeder screw and tried again. No movement.
View 4 Replies
My question is my abs light came on so I stuck my computer on it. Said right rear , we'll we all know on a 2007 6.0 f350 4X4, the there's only one sensor on the pumpkin, so I replaced it and cleared the code. Abs light came back on once I started driving, week ago my right front caliper stuck and got very hot, could that read bad for the rear of the front went bad? Will pull plug and make sure I didn't bend any pins.
View 2 Replies
I know this has been talked about many times and how to solve the issue but thought I would ask some other questions too. Earlier in the summer, I did grease the slider pins as preventative maintenance. I don't drive my truck all that much and when I used it yesterday, (about 30 minute drive) I came home to burning brake smell. I'm wondering if enough heat would cause the caliper to go bad? Should I just grease the pins again or change out some parts?
View 6 Replies
03 f350 4x4. New front calipers and pads.
Wondering if there's a 'trick' to getting the front brake pads into the caliper . Those damn springs kept popping out. I'd get three of the four ends into place in the pad holes then one would pop out while I'm trying to get the fourth in.
After about a hour of trying every different way that I could think of, another set of hands came by and with four hands holding things in place, it finally did the trick.
View 2 Replies
I have a 2000 f250 4x4 with 4 wheel abs. The front passenger side caliper keeps locking up while I'm driving and won't release and when I hit the brakes it pulls hard to the drivers side. I have put two calipers on the passengers side and put new brake lines on.
View 8 Replies
I have 2 F-350 4x4's and they both wander back and forth when driving. They feel like they don't have enough caster. One is a 2000 V-10 extended cab with 8 foot bed. The other is a 2015 6.7 diesel crew cab with 8 foot bed.
I have driven the 2000 for so many years that I have grown use to the very slight sawing of the wheel to keep the rig straight. When my wife got her 2015 it does the same thing. The 2000 is leaf spring and the 2015 is coil spring. This bothered me when I first got the 2000 (used) but I just figured it was part of
the charm of a big truck.
I know I could put a caster shim in the 2000 but there must be a better way to solve the problem. Both are stock, no lift and no heavy winch or stuff.
View 6 Replies
2004 PSD 4x4 72k. I thought I would be proactive so I bought the front ball joints and have plans to install them but recently I starting hearing (and feeling) a clicking sound in the front LEFT when I make sharp turns to the left and hit small bumps now and again. I jacked up the front end and am able to get 1/4" of movement front to back (top to bottom so not steering) in the wheel.
I narrowed it down to the hub. I took it apart and it is most likely a sealed unit so no adjustment is possible....that I can see.I pulled out the locking hub and got as far as I can to know there is not an adjustment. Need to confirm that it indeed is a sealed bearing and if so what are the part number(s) I may need to repair it.
View 14 Replies
I have a 1999 f250 sd with the 7.3. I'm not sure what is going on with my pickup. When I turn to the right i can turn with one finger, but when I turn left i have to put some muscle into it. Power steering fluid is full. I raised the front end and it turns both ways easy. My ball joints feel fine, there is no tire shake when i have it off the ground. My tie rods feel fine also, nice and tight. I was thinking about replacing the steering sector to see if thats the issue but wanted to get a second opinion first.
View 2 Replies
Driving on a paved road(some potholes but nothing bad) came to stop sign. After waiting for trafffic to clear, made right turn onto state highway truck began to pull to left, at first I thought i had a flat tire but every thing looked okay. Drove two miles to home, if let the steering wheel go, the truck would change lanes in about 25 feet...
2002 ford crew cab 4x4 7.3 power stroke 20k on Michelin.
View 9 Replies
At center, my truck is able to turn 2 1/2 revolutions to the right and only 1 1/4 turns to the left. Making sharp left turns is not possible currently. What needs to be adjusted in order to get the steering centered and even?
View 4 Replies
I have a 2004 super duty diesel 6 with electrical trouble dash lights stopped working put in new fusses where needed still no dash lights but now truck starts and runs ok but will not shut off unless I pull ignition.
View 2 Replies
97 f350 5.8L E4OD Transmission. This truck will not downshift when you come to a stop. You must manually shift it all the way through and then it does fine. What is causing this issue? It will kick down into passing gear. What is wrong?
View 4 Replies
I recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
View 10 Replies
