I have replaced both the transmission lines except the one that connects the two. It is the one near the top of the transmission that is about a foot long and goes from the fitting of the one transmission line to the other fitting for the other line. My questions is how do I remove it? It seems to be permanently affixed to the fittings, so those it come attached to new fittings?
View 2 RepliesOK, so I ordered in the new lines and have them. BUT my problem is snaking the factory transmission line out from under the truck. I have pictures to show my struggles.
How do I pull this:
Out of here???
Towards the front of the motor
Front passenger side cab corner
Replacing these lines? I don't care about breaking the old one, but I still need to find a way to install the new one.
I'm having trouble disconnecting the transmission lines to replace them. I can't get them off. I have the tool. Can I replace the fittings in the radiator?.
View 3 RepliesMy transmission cooling line is leaking. It leaks where it connects to the radiator. Im not sure how I go about removing the connection from the radiator. It is tough to tell from the rust on the connection weather or not I can use a wrench on it. I have read here that there are cooling lines in this part of the radiator for the transmission. Is it serviceable or do I need a new radiator. I dont want to touch it until I know what I'm looking at.
05 F250 5.4L 4x4
[URL]......
So this is my major problem, leaving for a camping trip tomorrow afternoon. It's just 15 miles away, easy flat drive. What has happened is the trans line coming out of the bottom of radiator is leaking next to the fitting about an 1/8 ' out, So I can't cut off and splice in hose for the trip. I worked on it for about an hour, rusted on, tried some heat and now have some PB Blast on it and all I am doing is starting to round off the head of fitting. Is there any way to bypass this just to get the camper to campground and then get to a shop while we are gone Don't care if I have to splice and cut, will get new lines later.
2004 f250SD 5.4 83000miles
So my 2000 f350 is leaking transmission fluid from the cooler line. It goes to the rear of the transmission, but where does it go to from there?
View 5 RepliesI have a 2008 Ford F250 V-10 Superduty and recently I had a transmission cooler line start to leak. I ordered replacement lines and the tool for the quick disconnect. The line that's leaking is from the radiator to the quick disconnect. I was able to replace the one line, however the second line (problem area) has been a nightmare. The line cracked right at the quick disconnect fitting.
The hard line is tight in the fitting and corroded. broke the tool trying to remove from disconnect. The line is flush with the quick disconnect. How to get that out of the fitting? or another method of fix? Its a hard 1/2 line going into connect crimped to rubber line going to transmission.
Have a 2007 V10 and I want to put in a Magnafine tranny filter. Instructions say to plumb it in to the return line. Which one is this, top or bottom?
View 11 RepliesI have heard that the front brakes are separate, and if the rear brakes have a leak and the line is empty, the fronts should still work. Is this likely to be true? If I drive the truck will I be able to stop with the fronts alone (assuming they will still work?)
I plan to drop the truck off late tonight when there is likely to be no traffic, but thought I would ask.
So my brother swears by sea Foam and has been telling me to run some of it through my truck. Question is,i just put new spark plugs in less then 5,000 miles ago. Will i have to change them if i run sea foam through the booster line and gas tank??
View 8 RepliesWhy on my 2001 Superduty if you blow a line nothing works and you have no brakes? On my older vehicles I think it was called a duel Master Cylinder and if you blew lines in front the back would still work and if you blew a line in back the fronts would still work. When I blow a line on my f250 there are no brakes at all making it quite deadly.
View 3 RepliesI want to remove the 4x4 stickers on my 2014 SD box. I think it looks cleaner without them. Are they difficult to remove or does the hair dryer trick and then some Goo-Gone do the trick without a big time effort? The last thing I want to do is make a mess of the paint finish.
View 13 RepliesLooking to get rid of the step handle, I did this mod on mine and it was a direct fit...take off old liner and unbolt handle, then get a liner from a non-step tailgate and it is a direct fit:
View 7 RepliesI am wanting to take off the center console lid to recover it. The only way I see to remove just the lid from the truck is to hit the rod out that is in the hinge. I was hitting pretty hard with a punch and it wasn't moving. I don't really want to break it so I'm asking if there is a different way or if I just need to use more force?!
View 4 RepliesIs it necessary to remove say about one and one half cups of oil from the HPOP reservoir when changing oil? I say not needed.
View 3 RepliesI dont want to pry on the wrong thing and brake something. I am trying to remove the headlight. I was told that their are some pins that need to be pulled up. I dont see any pins. I do see two plastic clips on each side of the headlight. They are flat on the top with a small slot in them. There is a "T" stamped on the top of it. Are these the pins? I tried to find a shop manual today without much luck. Looking for a picture to show the pins that need to be removed.
View 7 Repliesdoes it take a special tool to remove pcv valve from 2005 e-450 v-10
View 1 RepliesI pulled the trans to replace the clutch and now I cannot get the trans to line back up! I am using a trans jack then two floor jacks with a 4x4 across them to support the transfer case. I am about four inches from the block and either side is either 2 inches high or low. The truck is 1999 f250 7.3 4wd.
View 10 RepliesI filled my coolant yesterday after driving to the "max" line. Today when I awoke it was right at the "min" line. I didn't see any noticeable liquid below the truck, except under each front fender but I think this was water from the dew evaporating/condensing and running off the truck. What happened to the coolant or did it just cool down and condense. It got pretty cool last night (mid 40s). I have an 02 f250 5.4L ... I feel like there is a leak somewhere, any link to or a procedure they can explain for finding it?
View 10 RepliesThis is something to check, I found the vent line pinched closed on my 2000 F350 when I was trying to find out why it was leaking. When I was under my 2013 installing the hitch I checked it and found the same problem. The clip doesn't pinch it closed right away but it will happen if you don't move the clip.
View 8 RepliesFirst, I am fortunate that I was only going 25 mph when some turned in front of me causing me to slam on the brakes. The pedal went to the floor, but did slow the truck enough to miss the jerk. Had I been on the highway, it would have been very bad.
Anyway, what I found is still hard for me to believe for two reasons. It find it hard to believe it failed, but more important that I am getting the last national inventory of 2 of the 3 lines in this picture (according to my Ford dealer).
The three lines are almost directly under the front end of the master cylinder between the block and frame. These are as I found them. The larger one goes to the rear feeding both rear brakes while the two smaller run to the front brakes. The spring looking part below is just a plastic protector. The line which failed goes to the front left.
I think anyone with a 2005 SuperDuty which uses the same or similar parts should take a very close look at the flex sections. The parts I have ordered are: 6C3Z-2B523-BA, 6C3Z-2263-BA, and 6C3Z-2264-BA (rear, right, and left).
How long a manufacture is required to maintain inventory? I thought 7 years, but someone suggested 17. I'm at 8 years, but I would have expected more than 1 each of the fronts to be available. Do they changed parts on the '06 or '07?
My 350 spent 2 winters in the Chicago area and has been resting in Florida since 2006. No work was done in this area, but the closest work was the main fuel pump (frame mounted) replaced 2 years ago, but that is almost 2 feet to the rear.