So my brother swears by sea Foam and has been telling me to run some of it through my truck. Question is,i just put new spark plugs in less then 5,000 miles ago. Will i have to change them if i run sea foam through the booster line and gas tank??
View 8 RepliesHave a 2007 V10 and I want to put in a Magnafine tranny filter. Instructions say to plumb it in to the return line. Which one is this, top or bottom?
View 11 RepliesA few years ago I (for him) replaced all 4 calipers, rotors, pads, etc....things were good. Just recently he replaced his Brake Booster and Master Cylinder (not sure what led to this), but long story short everything is back together and he doesn't have brakes.
My GUESS is that the system needs a good flush, new fluid, etc....
My problem is I'm unsure how to bleed the ABS system. A few google searched indicate I need a scan tool, but is there another way? Can I jump something.
So my question, how do I completely bleed the brake system on this truck?
OK, so I ordered in the new lines and have them. BUT my problem is snaking the factory transmission line out from under the truck. I have pictures to show my struggles.
How do I pull this:
Out of here???
Towards the front of the motor
Front passenger side cab corner
Replacing these lines? I don't care about breaking the old one, but I still need to find a way to install the new one.
I have replaced both the transmission lines except the one that connects the two. It is the one near the top of the transmission that is about a foot long and goes from the fitting of the one transmission line to the other fitting for the other line. My questions is how do I remove it? It seems to be permanently affixed to the fittings, so those it come attached to new fittings?
View 2 RepliesI have heard that the front brakes are separate, and if the rear brakes have a leak and the line is empty, the fronts should still work. Is this likely to be true? If I drive the truck will I be able to stop with the fronts alone (assuming they will still work?)
I plan to drop the truck off late tonight when there is likely to be no traffic, but thought I would ask.
Why on my 2001 Superduty if you blow a line nothing works and you have no brakes? On my older vehicles I think it was called a duel Master Cylinder and if you blew lines in front the back would still work and if you blew a line in back the fronts would still work. When I blow a line on my f250 there are no brakes at all making it quite deadly.
View 3 RepliesI pulled the trans to replace the clutch and now I cannot get the trans to line back up! I am using a trans jack then two floor jacks with a 4x4 across them to support the transfer case. I am about four inches from the block and either side is either 2 inches high or low. The truck is 1999 f250 7.3 4wd.
View 10 RepliesI'm having trouble disconnecting the transmission lines to replace them. I can't get them off. I have the tool. Can I replace the fittings in the radiator?.
View 3 RepliesMy transmission cooling line is leaking. It leaks where it connects to the radiator. Im not sure how I go about removing the connection from the radiator. It is tough to tell from the rust on the connection weather or not I can use a wrench on it. I have read here that there are cooling lines in this part of the radiator for the transmission. Is it serviceable or do I need a new radiator. I dont want to touch it until I know what I'm looking at.
05 F250 5.4L 4x4
[URL]......
I filled my coolant yesterday after driving to the "max" line. Today when I awoke it was right at the "min" line. I didn't see any noticeable liquid below the truck, except under each front fender but I think this was water from the dew evaporating/condensing and running off the truck. What happened to the coolant or did it just cool down and condense. It got pretty cool last night (mid 40s). I have an 02 f250 5.4L ... I feel like there is a leak somewhere, any link to or a procedure they can explain for finding it?
View 10 RepliesThis is something to check, I found the vent line pinched closed on my 2000 F350 when I was trying to find out why it was leaking. When I was under my 2013 installing the hitch I checked it and found the same problem. The clip doesn't pinch it closed right away but it will happen if you don't move the clip.
View 8 RepliesFirst, I am fortunate that I was only going 25 mph when some turned in front of me causing me to slam on the brakes. The pedal went to the floor, but did slow the truck enough to miss the jerk. Had I been on the highway, it would have been very bad.
Anyway, what I found is still hard for me to believe for two reasons. It find it hard to believe it failed, but more important that I am getting the last national inventory of 2 of the 3 lines in this picture (according to my Ford dealer).
The three lines are almost directly under the front end of the master cylinder between the block and frame. These are as I found them. The larger one goes to the rear feeding both rear brakes while the two smaller run to the front brakes. The spring looking part below is just a plastic protector. The line which failed goes to the front left.
I think anyone with a 2005 SuperDuty which uses the same or similar parts should take a very close look at the flex sections. The parts I have ordered are: 6C3Z-2B523-BA, 6C3Z-2263-BA, and 6C3Z-2264-BA (rear, right, and left).
How long a manufacture is required to maintain inventory? I thought 7 years, but someone suggested 17. I'm at 8 years, but I would have expected more than 1 each of the fronts to be available. Do they changed parts on the '06 or '07?
My 350 spent 2 winters in the Chicago area and has been resting in Florida since 2006. No work was done in this area, but the closest work was the main fuel pump (frame mounted) replaced 2 years ago, but that is almost 2 feet to the rear.
Was thinking it was around 38 gallons but I'm thinking it's less than that. I have a 1999 Super Duty V10 with the long bed.
View 14 RepliesSo this is my major problem, leaving for a camping trip tomorrow afternoon. It's just 15 miles away, easy flat drive. What has happened is the trans line coming out of the bottom of radiator is leaking next to the fitting about an 1/8 ' out, So I can't cut off and splice in hose for the trip. I worked on it for about an hour, rusted on, tried some heat and now have some PB Blast on it and all I am doing is starting to round off the head of fitting. Is there any way to bypass this just to get the camper to campground and then get to a shop while we are gone Don't care if I have to splice and cut, will get new lines later.
2004 f250SD 5.4 83000miles
So my 2000 f350 is leaking transmission fluid from the cooler line. It goes to the rear of the transmission, but where does it go to from there?
View 5 RepliesI replaced a rear rusted brake line a couple of years ago. It rusted where the line met the bracket. I'd never done this before but bought a flare (flaring?) tool and fixed it.
This week the longer line that runs down the length of the truck started leaking. It looks like the line was once held in place by a small bracket just in front of the rear wheel but it wasn't in that bracket anymore. I guess it rubbed against the metal and water/sand rusted it out.
A local garage said they'd need to drop the fuel tank and estimated that it would be several hours (and hundreds of dollars) to do the job. It looks like I might be able to cut the old one out and then fish the new line up through there and replace it.
Also, what is the diameter of the line? It is a 2004 F350. I can certainly cut it out first and then take a piece of it to the local auto parts place to get the replacement line.
I have a 2001 F-250 7.3 diesel with an automatic trans. Over the last couple of months it has stalled 3-4 times while driving, always when slowing down but even at speeds of 15 mph or so. I did find a burnt vacuum line the other day. It comes out of some type of relay box located behind the battery and in front of the starter solenoid relay and is mounted on the fender. It has an electrical plug in the top and two vacuum lines at the bottom. I am hoping this is the cause of the truck dropping off of the idle circuit? But I don't know what the unit is so I cannot order the correct replacement lines.
View 9 RepliesOn my '97 F250 the rear brake line going to the rear right wheel has a rusted hole. It measures 50" total. Instead of bending a new metal line. I see they have a "poly armor" line that can be bent by hand( no tools needed). I see Autozone has them.
View 14 RepliesHad the rear passeneger side brake line burst today in rush hour traffic ..wasn't much fun. Is it a easy to do it yourself deal ...it is a 2003 f250 v10 triton .
View 1 RepliesNeed to know if the brake line fittings are SAE or metric? Mine blew a leak on the line that runs behind the gas tank on the drivers side frame. It's a 2004 5.4l f 350 4 x 4, 4 wheel disc brakes...
View 4 Replies