Ford Wiring/Electrical :: 2004 Taurus Hard To Start / Cranks But Acts Like It Is Not Getting Fuel
Oct 31, 2012
While the owner of 2 Ford Trucks, I also have a 2004 Ford Taurus with 28K on it. For a while now the vehicle is hard starting, cranks but acts like it is not getting fuel, however, I can hear the pump come on. Other times it starts right up, but a clicking sound can be heard coming from the firewall area. At times the gauges will not immediately respond when the Vehicle is started and then all at once they will begin to work. Now, my check engine light is on, but my hand held obd will not read it. All the terminal pins look great, obd tester works on my other two vehicles, cigar lighter working, the fuses i checked are good. Vehicle runs great. Can this all be related to a bad module?
View 1 Replies
Advertisement
I just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 Replies
I have a 02 f350 v10 with a starting problem. Sometimes it will crank but really slowly almost like the battery is dead, but its not! bench tested the battery and actually just bought another new one. And with the same result. I tested the relay that's on the firewall in between the starter and the battery and it checked out, i also bought a new relay and i want to put it in except I haven't figured out which wire goes to the coil and which one goes to the ignition. the battery and starter poles are marked and easy to follow ..
Also last month I changed the starter but I'm starting to get desperate and i think I'm going to take it off and have it bench tested as well. I'm just really at a loss in which direction to go. The truck on the outside really looks good but living in the northeast the frame and probably most of the outside grounds are toast and I've been renewing or just placing them as I come across them. Before i forget i tried jumping the starter directly from the battery with cables and got the same result. it would crank but too slow to actually turn over.. Sometimes my radio and ignition lights will sometimes come on without the key in the ignition..
View 6 Replies
My F250 is acting like the battery is almost dead but its not. I've checked all the grounds I can think of, used jumper cables and clamped right to the body and still nothing. I put my battery charger in place of the battery and my charger almost caught fire! Where are all the ground points at and points to check? It was doing fine then this. I only found 3 ground points on the block and I bypassed all of them and nothing. There are 2 large on the front of the block, I was able to get one loose and "clean" it but not the other. The block to firewall is currently off so I can clean it in the morning.
But it didn't do anything. I can clamp anywhere are get the same results. There are a few threads about this truck and trying to get it back into shape. When it worked, when I turned the key on, gauges worked, RABS, Engine, and Battery light came on, GPs kicked on, etc... now, I get a very faint Batt light, Erie dinging, and not even the stereo now. This truck has been an electrical nightmare since day one. Spent 4 days on just under hood electronics alone. Haven't even moved towards the back. Also, Instead of using a 2/0 AWG wire to the starter, Can I use two 1/0 AWG wires to it instead since they used two separate grounds? It also still has a 2G alt.
View 5 Replies
So heres the deal 1989 civic dx hatchback 106k on the odometer automatic 1.5l d15b2 engine . It's been having delayed starts taking 3 to 6 cranks before firing up then running fine, suddenly it dawned on me maybe it was the distributor , so I swapped it with a spare I had because sure enough the old one had red death red dust in the cap. Cleaned the contacts set the timing reassembled, some wires broke on the back of the wiring harness to the distro. Rewired them, the car kept getting worse I jumped it and took it to my friend a vw mechanic it drove 49 miles there fine after the jump, new plugs new wires new fuel filter we did the wire job set the timing checked the timing belt got the battery tested and the alternators new and did a oil change also did a coolant flush a few weeks ago.
It started right up drove it back to Chicago , in the morning I was getting off the highway it stopped running no noises I pulled over 8 cranks later it started parked it 3 blocks away, went to test drive it when I stopped at a light it shut off cramming it and hitting the gas pedal got it to start drove it a block down it shut off at a stop sign and I parked it. What it is I'm throwing code 8 which is a top dead sensor which I think is in the distro which I replaced a month ago. Fuel pump sounds like its priming but you have to gas it and crank it to start it which is odd for a automatic , it is girk injected is this tds sensor going to do that by itself? Or could it be a ignition module? ( what I read online) starter? Main relay , fuel pump switch?
View 6 Replies
My 92 F250 5.8 won't start but fuel pump runs all the time the key is on. Some times it runs. But has no power and check engine light is on.. But I cant get it to flash codes, only steady light on.. It did this before then ran good. Now back to no start.. I checked grounds and relays ..
View 2 Replies
Been having an odd problem with getting my truck to start. Pass couple of days I've gotten out from work and gone to start the truck. It cranks just fine but wont start, acts like there is no gas. Let it for a minute or two and try again and it will start right up and keep running with no other problems. Go to leave for the work the next day and the same issue. Weird thing is the problem only seems to happen when its cold out 30F so or below. I was thinking fuel pump but I'm not sure. What to check?
Edit Its a 2002 Excursion XLT with the gas 5.4
View 8 Replies
So I've been having problems with my old duraspark 2 ignition box and I replaced that but it didn’t seem to fix the problem. The truck doesn’t start if the voltage is down around 12v, it cranks but no spark. So I put it on the charger a couple hours ago and came inside and was reading old posts on here about testing the ignition system and then just went out to test the negative side of the coil with a test light and low and behold when my assistant went to crank it over the truck started right up like everything was fine. I took off the charger.
So then what I did was I checked the charge at the battery while the truck was running with a dvm and the voltage was 14.33 then I turned on the electric fan and it jumped up to 14.88 and spiked at 15 then held at 14.88. is that normal or is the voltage a little on the high side? If it is high then could it be the voltage regulator or alternator? And could that have been my problem all along instead of the ignition module?
View 14 Replies
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
Im installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 Replies
I have a 1995 Ford Taurus, and I just swapped in a new engine from a donor from 2000. The engine is a Flex Fuel 3.0L Vulcan OHV.I've got a wealth of background knowledge as a mechanic [5 years+] and an electrician [4 years+]I have swapped over everything required to make this work, in theory. I swapped exhaust, fuel system, and computer/harness and all the relays to go with it. I also made a custom gauge cluster from a 2000 Taurus as well.
Well everything works just peachy, all the wiring for the most part is correct minus a few buzzing relays that I just need to work out. The main issue this [now monster in my eyes] has is the PCM is not telling the FPDM to tell the Fuel Pump to start. Turn key, and no 3 second startup. I've checked the fuel pump, and it's fine. I replaced the PCM and that didn't solve it. I have the security system from the 2000 in there as well, thinking that was an issue. I also have the emission sensors and canisters installed, just like you would see in the 2000.
I'm at my wits end trying to figure out why the PCM isn't sending voltage out to the FPDM. I had to of missed something along the way but I double checked and still can't find anything. How to get this working properly.
View 17 Replies
My truck's been having an occasional hard start, meaning the engine cranks strong but it fails to catch and then sputters. The 2nd start attempt usually fires up with no issues and then runs perfectly otherwise.
MPG's haven't changed, fuel filter was changed 15K ago. Air filter is clean. Plugs were changed about 10K ago. I always use Shell/Chevron gas. MAF sensor looked clean when I took it out so I didn't do anything to it.
This is starting to happen more frequently, maybe once every few weeks and I get a feeling it's the start of something. I've found myself waiting a few seconds for the fuel pressure gauge to come up before turning the key to start reliably. In the past, I could simply flick the key and it fires up the first time.
I see posts talking about the fuel pump module above the spare tire. What are symptoms of that going bad? Any pending codes that might be stored?
I'm about to get myself a scanner since I need one sooner or later. Which specific PID's to check while debugging this?
View 6 Replies
Just recently bought a 07 Nissan Maxima SE. Has a few issues.
The car sun roof does not work at all. It worked the day I bought it though.
Has issues turning on. Cranks slowly then after a few seconds of struggle it turns. Didn't have this issue when I bought it.
Goes idle when first starting to drive. From park, I put the car in drive, or reverse, and let go of the brake, it basically does nothing. Engine is on as if it were in park or neutral, but the car doesnt move. When I press the gas it takes a few seconds before it decides to actually move.
View 2 Replies
My 1999 Ford Ranger XLT, 6 cylinder, auto trans, with 134K miles has an electric problem. When I turn the key to the 'on' position, all dash lights show normal, headlights work, radio plays, etc. But when I turn the key to the 'start' position, all electric power is lost. The power remains lost until I disconnect and reconnect the battery ground wire. After reconnecting, I again have power until the key is turned to the 'start' position. I was able to jump start the truck, so I assumed I needed a new battery. I bought one a week ago, and was back to normal until today. The truck started, I drove 4 miles to the grocery store, and then I found myself back to square 1 (i.e., the no-start situation).
View 3 Replies
I have a main tank and an Aux tank with a gauge selector switch. I believe I may have a bad fuse as the indicator has stopped working. Where it is on the fuse block??
1978 Ford F-250
View 1 Replies
I swapped a 4.9l into a 1997 F-350 that had a 5.8L originally, my issue is the fuel injectors are not working. I did my homework and got the harness that was with the engine out of a 1995 F-150 and also got the correct PCM to go along with my E4OD tranny that is in the F-350. It has spark and 60 plus PSI fuel pressure in the rail and will run with starting fluid shot in the throttle body. Both vehicles came with OBD I so should be compatible there. I do not have 12v to the injectors and obviously the NOID light shows no pulse either. Could be a ground but not sure where to look or what else could cause this.
View 14 Replies
I have a 1994 Ford Ranger king cab 4x4 with a three inch lift kit on it . My problem is the fuse is blowing that goes to the fuel pump . It started out blowing the fuse now and then when it was raining . Well I thought it mite be the fuel pump going bad but after I put the new pump in the truck it lasted about a week and started blowing fuses again . I put another fuse in and it go a few days and blow it . Last week on a 100 mile tripe I got almost there and it burned a fuse on the highway . I tried to put another fuse in and it would blow it as soon as I tried to start the truck . Burned five fuses right then . So I had it towed to mothers house and put another fuse in and it cranked up . I looked at the wiring that was not wrapped in that plastic cover stuff and have not found anything yet ...
View 14 Replies
I have 2 1986 Ford F250 supercab I switched cabs to put the better cab on my truck power windows wipers heater blower motor all light signals work no fuel gauge power or fuel pump power no power to the inertia switch
View 12 Replies
I've got a cold start problem. Turn it on, wait until glow plug light goes off, hit the starter and it fires right up. It acts like it runs out of fuel and dies. Hit the starter and it fires up and dies again. Third time it stays running. It's not a long crank either. 1-2 seconds at most. Fuel pressure is 59, HPOP immediately goes 1000+, everything looks good. It will start fine the rest of the day until it sits overnight. This is an early 04.
View 14 Replies
After changing my radiator support, my fuel and temperature gauges don't work. I looked to see if everything was plugged in and I don't see anything unplugged. I do know the older trucks used the V-R regulators, but I don't know about this model.
View 2 Replies
I have an 01' f150 that everything is going out on. I've replaced the GEM module thinking that's what it was to no avail. First thing to go was all four windows which have currently been stuck halfway down for 2 weeks. It's stalling out during idle like it isn't getting enough fuel to it. Brake and engine light on dash are staying on. Radio, interior lights won't come on. Will not come out of park once in. I have to do the old forward, back, middle key trick to get it out of park into neutral so I can start it and go. I've also checked all fuses and relays under dash and under Hood.
View 3 Replies
