having some issues with my idle, when im coasting and i push in the clutch it doesnt drop down to idle like it used to it sticks at about 2000 when its dropping, also at a stop light the idle will rise up and hunt from 1700 to 2300 or so. also if im in a parking lot in second gear or so the rpms will rise and accdelerate the vehicle.
View 1 Replies2003 Jetta, 1.8T, 5spd, stock, 129k miles. I am working on a friends car and his complaint is the clutch pedal occasionally sticks to the floor and during this sequence it is hard to shift gears. I removed knee bolsters to inspect under the dash and found all linkage straight, all plastic parts/springs in place and no fluid leaks, I removed slave cylinder from bell housing and found smooth operation and no leaks. I guess I could replace both but I am wondering if there is a common issue. My searches have found broken plastic parts, bent push rods and leaking cylinders.
View 4 RepliesI replaced both rear calipers, rotors, pads, parking brake cables and it still sticks once in a while. I have played with the adjustment on the console many times, but to no avail. I have to crawl under the back and press the link up to unlock the parking brake. It's only about a 1/4 to 1/2 inch at most. Is there some type of spring I can use so it retracts all the time? I have seen Toyota's with them.
View 4 RepliesAC went out last week, was working great earlier that day. Checked under the hood and the clutch isn't engaging. Noticed an RPM spike every four seconds or so at idle when the AC was on. Checked voltage coming off the wires that go to the clutch and saw a voltage spike from essentially nothing to 9-12V which occurred in sync with the RPM spike. I poked a screw driver in the high pressure port and got a nice blast of coolant so I figured refrigerant isn't the issue.
Fuses are all good, in car and on battery. Replaced the fan control module and now there's no RPM spike and I get a constant 12v with the AC on at the clutch wire, but it still doesn't engage.
It's a 2000 Jetta 2.0 auto.
I've searched but can't find what my problem is , ON idle when clutch is not depressed loud ticking noise , but when I push the clutch in it goes away . Also the ticking noise will get louder if I accelerate . ONLY Im first gear will I hear a loud grinding noise which means I have to quickly switch into second . Sound similar to something being dragged along a fence . Again the grinding sound I'm first will only happen if I'm giving it gas. Car has 325,000 km . Something with the transmission ?
View 1 Replies2000 GTI
260,000 miles (60% highway)
2.0L 4cylinder AEG
All stock.
I have a new issue developing on the clutch of my car. When I fully press the clutch pedal to change gear, I hear cacophony of grinding, hissing and whirring noise, probably coming from gearbox. When I take my foot off of the clutch pedal completely, the noise is gone. half clutch has reduced amount of these noises. I had this symptom briefly one night two weeks ago and when I topped up oil, this was gone. Tonight, it is back.
I have a 2000 jetta 2.0, and the idle seems to rough and when I start the car it seems like I might stall.
View 9 RepliesI have a 2000 f150 lariat 5.4L 4x4 and when i start my truck up when it is usually below 40 my truck will idle around 300rpm and shake. It also makes popping noises in the exhaust. I am getting codes PO171 and 174 (running too lean in both banks) I have replaced my IAC, plugs, pcv valve, air temp sensor and MAF sensor and 02 sensors and nothing has changed. I have tried looking for for vacuum leaks using carb cleaner and starting fluid but i nothing has came up. I took it in to a mechanic and he suggested a bad intake manifold but i searched for a leak and found nothing.
View 14 RepliesI have 2000 Jetta 1.8t. Over the last few weeks it idles wierd when up to full operating temperature. The check engine code is p0411.
View 3 RepliesThe check engine light came on in my 2000 Jetta and the engine power suddenly decreased noticeably. Got worse quickly and was idling rough, like it was about to stall out (but didn't). Took it to dealership, they said spark plugs were the problem and replaced. All seemed normal driving home, but after 10 minutes, same problem: check engine flashing, weak engine (trouble on hills), and a rough idle.
Two questions: what could it be?
and is it safe to drive back to dealership (~10 miles) or might that cause further damage?
Having trouble with my '00 Jetta 2.0 A/T w/ 98K miles. Had the water pump replaced @ a year ago (for the 2nd time, the 1st replacement died after <15K miles.) The car has had issues with rough idle when started, especially with a cold engine, since before the 2nd water pump. I've replaced the coil pack, thermostat, and coolant temperature sensor in the recent past in addition to the water pump & timing belt.
The gas mileage sucks, and when it's idling rough it doesn't "idle up", & will stall if the gas pedal is pressed with 30 secs. of starting. Otherwise it seems to run fine. The coolant temp. sensor was replaced after a CEL indicating it was bad. The CEL went off after it was replaced, but it's now throwing a P1296 Cooling System Malfunction. I have noticed the temperature gauge fluctuates instead of staying around the "middle" since the 2nd water pump replacement, and will run "colder" in colder weather. Since spring is here, the temp. gauge stays around "normal", or the middle.
Some research online says thermostat OR coolant temperature sensor. Since the gauge registers normal now, I'm leaning towards a bad temp. sensor...?
Does the hard start/rough idle and the cooling system malfunction CEL could be related?
I drive a 2004 Kia spectra (base model) w/ 93k
My clutch would start out fine as I start the car, but after pressing on the clutch pedal for about 40-60 times on one trip, it'll start to loose pressure & becomes stickier. And as I press on the clutch pedal more & more, the problem gets progressively worse to the point where I have to manually pull the clutch back up with the tip of my foot.
I also notice that when I drive with the air conditioning, the problem would precipitate earlier & clutch response deteriorates much quicker. But when I let the car rest for a couple of hours or overnight, the clutch response would slowly return, and eventually be normal again.
I own a Honda Accrod 2005 V6.
I don't know much about cars, but for the past year my clutch gradually started to just stick to the floor. I'm now at 80,000 miles, the clutch doesn't slip, and it for the most part drives fine with exception to this sticking. Sometimes when this happens, the stick shift stays in gear and I can't get the stick out of gear until the clutch has been lifted up and pushed back in. It is def getting worse. I have brought it to several mechanics.
I have been told by Honda that I need to replace the clutch set (clutch disc, pressure plate, and throw out bearing) and the clutch master and slave cylinder.After another mechanics look over, they also did confirm the same as honda but stated to get a new cut flywheel.
But after several other mechanics look-overs, they told me that the clutch is fine, so they recommended me to get the master and slave cylinders replaced.
So, trying to save money a mechanic told me to take one step at a time and see how it goes. He said he will bleed the slave and master cylinders and see if it is just an air pocket. That didn't work, so I trusted him and he replaced the master cylinder, but the problem still exists. He said the next thing to do is maybe to do a new slave cylinder. I'm now contemplating.
Another mechanic took a look after the work was done and said there is no leaking.
I have a 2009 stick-shift 4WD ford ranger with a clutch that is sticky in 1st and reverse. Basically it requires alot of force to push it into 1st or reverse, but this problem isnt always there, and it the problem dosnt seem to pop up under any particular circumstances - e.g.: the weather, if the tuck has been driven recently etc. I paid $5000 for extended warranty when i bought this truck new, and the dealer repair shop tells me that they can't tell me if it is covered under warranty until they take it apart to see if the problem is a "wear item" .
If it's not covered under warranty then I am stuck with the $700 bill. Otherwise the truck runs great, and I have never had any work done under the extended warranty. The warranty runs out soon, and I am wondering whether to take a chance with a rebuild. My wife dosnt like to drive the truck with the clutch like that because she is afraid of getting stuck at a stoplight and being unable to engage the gear.
Heat blows warm at best and A/C isn't all that cold. I want to believe its a blend door issue and dive into it this weekend and fix it but there isn't a single piece of foam coming out of any of the vents. Of all the systems on the car HVAC isn't my cup of tea I don't know anything about it. What else could be the problem?I can live without A/C but the heat things must be fixed.
View 1 RepliesI have question about power steering pressure switch in golf 4 1.8t
Idle go high to 2000 rpm .. when i plug-off the Power Steering Pressure Switch its go fine .. i want know is this " Power Steering Pressure Switch " effect stability in high ?
My 1999 Toyota Tacoma (Ext Cab, 4x4 TRD) has 162K miles and now the clutch pedal intermittently sticks to the floor. I have to pull it off the floor with my toes while driving and have also felt the pedal start to pull back towards the floor on its own while the truck is in gear.
I'm looking for some wisdom as a few blogs/websites point towards a master cylinder, others say the master and slave, and my local auto shop said I need to replace the entire clutch assembly and throttle bearing. My truck is no spring chicken anymore but I'd like to keep it running for a few more years...
Well my alarm is not working properly, when lock my doors all my doors lock but yet my headlights don't flash and i dont get any alarm chirp..
View 2 RepliesI am having issues with our 2001 vw jetta wolfsburg edition with a AWW engine the cooling fans not working properly. I had a bad fan and replaced it and since changed the thermo fan switch and the module under the battery and still no luck. With the key off I can jump the fans via the plug for the fan switch only low speed works with the key off. with the key on i can get both speeds of the fan to operate. With the ac on the fans operate.. normal driving the fans will not operate. and the engine will overheat and fans will not go on. Any other relays or sensors that could be faulty?
View 2 RepliesBought a 2003 golf gti 1.8t as kind of a project. Car had no interior no exhaust and some shifting issues. To fix the shifting issues rather than replacing solenoids I just got a rebuilt valve body. After installation the car still doesn't shift from 1st to second properly and now I don't have reverse. (It's an 09a transmission)
View 1 RepliesCrank position sensor was replaced a few months ago. After that noticed that it would not accelerate properly from a standing start. No jerking or anything, but way back it used to be able to spin the front tires a bit, but now not getting that needed acceleration. After hitting 15 or 20 mph, then it's back to normal and road and highway speeds are nice with power.
The reason the crank position sensor was replace was on account of intermittent no starts. That's gone away, but now this acceleration problem. Could it be a leaking air from the outside into the intercooler? Would a VAGCOMM show what's going on? Golf TDI 2005...