Golf IV / Jetta IV :: AC Clutch Doesn't Engage
Aug 25, 2015
My AC doesn't work right now, however, sometimes it works. It's very random, it doesn't matter if its hot outside or if its cool.
What happens is my AC clutch doesn't engage. when I turn ac on, it raises the idle for a second, and as soon as it does that, my ac compressor gets around 12 volts for less than a second, and the idle drops again. it does that in a loop.
My fans work fine, both high and low speeds, everything else works, all the fuses are good. I changed the pressure switch, didn't fix the problem. I also checked the ac coil and clutch. everything clicks and works. ground on the compressor is good.
Other odd thing - positive wire on the compressor constantly getting around 3 volts. What can it be and what else do i need to check?
View 24 Replies
Advertisement
AC went out last week, was working great earlier that day. Checked under the hood and the clutch isn't engaging. Noticed an RPM spike every four seconds or so at idle when the AC was on. Checked voltage coming off the wires that go to the clutch and saw a voltage spike from essentially nothing to 9-12V which occurred in sync with the RPM spike. I poked a screw driver in the high pressure port and got a nice blast of coolant so I figured refrigerant isn't the issue.
Fuses are all good, in car and on battery. Replaced the fan control module and now there's no RPM spike and I get a constant 12v with the AC on at the clutch wire, but it still doesn't engage.
It's a 2000 Jetta 2.0 auto.
View 6 Replies
My starter motor in my 2004 Golf 2.0 doesn't engage or spin when it is very cold. By very cold, I mean below 5F.
The battery has plenty of juice, and jumping the battery doesn't work. I turn the key to "start" and nothing happens. When key is in the on position, fans, wipers, etc all work fine. When the car warms up to 20F or so, everything is fine and the car starts.
Here's the funny thing. If I put a little space heater on the driver side floor to warm up the fuse and relay panel, it starts with no issue.
I don't know enough about the interlocks between load reduction, starter motor, ignition switch etc to make a good guess as to which relay (if any) may stick in extreme cold. It's a tough problem to diagnose, because I can only experiment when it gets REALLY cold, when it isn't very fun to experiment anyway. I don't think it's the piggy back harness, because the wipers, horn and fan all work.
View 4 Replies
I had to replace one of my Ac lines. The skinnier one.I have never seen the air work in this car. That line was broke since I have owned it.
I went to try and fill it today with r134. I have as much pressure on the low side as I can put in. (55 says the cheap gauge) But when I turn the car on the clutch does not engage to cycle the freon so no cold air. What I know,The fans do not turn on when Ac button pushes.The connector to the compressor only read 4v. I cannot get any number on the high pressure switch connector. (3 pin)
I don't know if it just doesn't turn on because nothing in the high side? Is there a way to bypass? I read jumping the switch is a bad idea.
View 2 Replies
I got a 2003 GTI 1.8t and the AC air is blowing warm. With the car on, AC on and fans full blast both rad fans turn on but compressor clutch does not engage. Took it to a shop and the mechanic said the system was full of refrigerant but that the compressor was not getting the proper signal and there was an electrical problem.
I check the power at the compressor and it is reading about 7 volts, which is low correct? That should be getting 12-13 volts correct? I also check the pressure switch over by the passenger side and it was getting 13v. What to check next to start ruling out causes? Any quick way to determine whether this is electrical or a compressor issue? I am limited in my abilities as far as electrical work goes.
View 2 Replies
So I just bought a 2000 MK4 Jetta for a $1000, its been ok, replaced the breaks, rear calipers, swapped in new headlight socket, swapped in amber tails, new plug wires, new drive belt, water pump/ timing belt all new.
Car has 173,xxx and i drive in pretty bad traffic daily, there are times when i am going to accelerate and between 2-3k RPM it feels like the clutch disengages then re-engages for a split second. then continues to drive normal, happens 2nd, 3rd, and 4th. Is this the clutch slipping? will it be fixed if i were to order a new clutch kit? I am on a budget and do all my own work, so i can't afford to buy a new clutch kit and have this not fix the problem.
Also, the car gets a little wiley on the free way, feels like its the struts, but the steering wheel vibrates a bit, i just found out the PO had different rims on the car before. So the tires might need to be balanced. I JUST Ordered new Racelands hopefully to stop the creaking/bounciness of the suspension. How to get this steering in check.
View 6 Replies
Just picked up a 2004 MK4 Jetta GLS 2.0 for really cheap.
As the title reads I have found some issues with the car after giving it a once over.
Dash/Radio lights - My Dimmer Switch is not getting power. I was wondering what the next step would be. I checked all the fuses and there is no issue.
Cooling Fan - I read about testing the plug and a CFM. Which should be done first?
A/C - I changed Electrical-Switch & Relay: A/C Clutch Switch and it did not fix the issue.
View 5 Replies
I have a 1995 Ford Windstar. When I turn on the air conditioning, the compressor clutch does not engage despite having sufficient refrigerant in the system. Jumping current directly to the compressor clutch will engage the clutch, so it's not the clutch. I suspect the relay for the compressor clutch inside the CCRM may be bad, but am not sure how to test it. I have a Haynes repair manual, but how to test this device?
View 12 Replies
148,000 miles, and yesterday my R decided it would no longer allow me to use first gear. It sort of starts to go in gear, but feels kind of mushy, not positive, and if I let out the clutch, the gears grind, but will not engage. All other gears feel and perform normally.
View 7 Replies
My wife and I have a R and a rabbit, she drives the R mostly and i drive the rabbit mostly..... I drive further to work, anyhow the past week she told me that the clutches feel like they are slipping and when she puts it into drive sometimes it wont engage... or when she puts it in p it says in d...... anyhow off to the dealer it goes for who knows what and how long... and the car is stock....
View 24 Replies
I've been experiencing a loud clutch squeal or screech when I first engage the clutch after the car has been sitting for longer periods of time, overnight etc. It goes away after a few shifts and only returns after the car sits for a long period.
I brought it to the VW dealership since I'm still under warranty for a bit. After two visits the have come up with two hypotheses without any evidence. They claim to have not heard it or found anything wrong visually.
1) it could be a rear main seal leak. Or leak from somewhere on the tranny onto the cultch. When I first drive it is burned or wiped away. After putting on the lift they found no evidence of leaks. So hypothesis two:
2) Thy flywheel may be developing a bit of a patina of rust. After the clutch is engaged a few times, the rust is gone and the squeal goes away.
View 4 Replies
2nd gear runs fine, but occasionally, when in first i have a real bad stutter in the engine and it continues from the moment the clutch begins to engage on up. The car just seems to jump or skip along rather than run smooth.. It occasionally will work itself out but other times will continue for 5 seconds at which i switch into second gear and everything is gravy from there. What the main root cause of this is? I don't want to get the wrong thing fixed which I've been trending on lately.
View 4 Replies
I went driving today and for a moment I could engage/disengage the clutch pedal with little to no effort. It goes back to the normal force after 3-4 shifts.
It's the exact opposite of what's happening in this thread. [URL] ....
View 11 Replies
MKIV jetta GLI, first two gears just won't engages as if it's still in neutral. Have to start her moving from 3rd. What could be the issue?
View 14 Replies
I have an 02' 2.0 Jetta Wagon, and the A/C is having some issues. Since I know close to nothing about A/C systems, I took it in to a few places to have it looked at. I've had the whole system Evac'd and recharged, and have had the low pressure fitting replaced (apparently there was a slight leak there), and the system is still not working.
The A/C worked fine when I first purchased the car a few months ago. Shortly after my 800 mile trek from Oregon, back to home, the A/C started to only work intermittently. The compressor would engage, then disengage, repeat...It seemed like a bad idea to keep trying to use it in its sad state so I stopped using it altogether. As I said, I had the system emptied and recharged, but it still only works intermittently. It sort of follows a pattern where upon start up it works longer, and switches on and off at shorter intervals, until it doesn't engage at all.
There are no strange noises from the compressor, and when it was hooked up to the machine, it proved to be performing its function well.
View 5 Replies
Compressor does not engage, and my fans do not come on when I turn on the A/C. They do come on low speed when I jumper pins 1 and 2 on the temp switch plug, but they do not come on high speed when I jumper pins 2 and 3.
I have replaced the FCM with a new one, as well as a guaranteed working used one; neither one changed anything. I assumed right away that it was the fcm because my original one has a hole eaten through it from battery acid.
Compressor clutch ohms out within spec, and it will engage if jumpered.
View 3 Replies
I have a 2002 Jetta 1.8t and the A/c doesn't work. I took a look and I know that the clutch/compressor does not engage. also, the rad fans do not turn on when I have the AC on in the car. all I get is hot air. I tested the line and there is no freon in them whatsoever. which is why the compressor is off. however, I can't add any freon without it working. I checked the fuses on the side of my dash and on top of the battery as they seem to be ok. Also, I was told that I just need to replace the compressor with a new one and I should be good to go. Is this true? It will be an easy fix if it is.
View 13 Replies
I recently bought a volkswagen jetta 1.8t wolfsburg edition 5speed. While driving i switched from third into fourth gear upon letting the clutch completely out the rpms began to spike and no power was being produced. So I neutralized to the nearest stop and tried shutting my car off and restarting it and then putting it into gear it would not engage in any gear what so ever at all. The clutch then had no pressure or resistance in it when pressing down and lets up slowly.
The motor stilll runs perfectly fine and the actual shifter will move into gears in the gear box but the clutch still has no pressure and doesn't even attempt to catch or engage in any gear. Do i just need to replace the clutch or the intake or the flywheel or what? In addition i have since ran the code runner and nothing comes up besides the intake code but that's because i took the intake off to manually try and engage the clutch into gear witch still did not work.
View 2 Replies
I'll start this off with a few months ago, I went on a trip and along the way noticed that the car wouldn't get into gear. This happened for a few moments, and solved itself.
Fast forward to a few days ago:
So, my Golf MK4 AUTO 1.6L transmission doesn't want to shift into 4th, sometimes.
One and two are good, but sometimes I get quite a lag in between disengaging 2nd and getting 3rd also.
Furthermore, sometimes I get 4th 'semi' engaging, where the engine is revving too much to be fully in gear, but I get power to the wheels and accelerate (slowly).
I did a VAGCOM scan and got the old:
00652 - Gear Monitoring
27-10 - Implausible Signal - Intermittent
I also had a CEL on my dash, which I cleared with the VAGCOM. This removed the light, but of course the error still persists.
I've been reading around, and some people have said the issue is the TCM, but some people have had similar problems and a TCM replacement has not fixed this.
(Just btw, my TCM model is 01M927733LK).
And some people have had good results with solenoid replacements. So, I was thinking of doing a ATF flush, just because it was recommend on some posts, but won't necessarily fix the problem.
Contacted a garage to do this for me (never flushed automatic tranny before) and mentioned the VAGCOM codes, and he said this is a slip code.
So, now I'm not really sure what to do to fix it. Are the solenoids interchangeable? Am I able to switch two gears' solenoids to see if it moves the issue to another gear, proving its the solenoid?
View 1 Replies
03 Jetta 1.8T AC is giving me fits. When the compressor comes on the AC is nice and cold. Problem is that it isn't on very much. Today was a good example. No AC for about the first 30 min drive to get an oil change (local driving). Next 40 min highway drive, AC only got cold for the last 20 minutes and then started to warm up before I got to work. Drove to auto parts place at lunch, AC cold from start to finish. No AC all the way back to work.
So, this evening I started the car with the hood up and watched. Compressor wouldn't engage. Pushed the AC button a couple of times and clutch engages. Compressor stayed on for 7 minutes and ice cold air. Clutch then disengaged and immediately both fans went to high speed for about 5 minutes with warm air out the vents.
Fans cycled back to low speed and compressor clutch engaged again for about 2 minutes this time. Fans to high speed again for 3 minutes, then compressor engaged for only a minute. Each time the compressor shut down, both fans would go to high revs. The minute they would go to low speed, the compressor clutch would engage and I'd get nice cold air..
Just had the expansion valve replaced and r134a charged by and AC shop last week. I have had the on/off AC problem for months and then could not get the compressor to engage at all for about one month. Of course, just as I was getting to the shop, it started blowing cold air.
Not sure whether I'm looking at an electrical problem or what. Just seems odd that both fans suddenly speed up and slow down and the compressor engages only on low speed.
The only other odd thing I've noticed is that cold or hot, as soon as I turn the ignition on (engine off), one fan continually starts cycling on and off. It does that continuously. I've checked the fuses on top of the battery and they all look fine. No appreciable drop in RPMs when the compressor engages. Fan control module?
View 7 Replies
Last year I had an issue with starting my 1.8t Jetta Gli. Every couple of weeks, the car wouldn't start unless I keep trying or come back after a couple of hours. I then thought it was the cranks sensor and had it replaced. Unfortunately, the problem is back! The idle seems a little jumpy, car isn't as smooth as I'd like it to be. It also doesn't seem to have a strong start. I can't figure out what it exactly is, and I don't want to start changing random parts. I was debating on perhaps getting a new fuel pump, coilpacks...
View 1 Replies
