Golf IV / Jetta IV :: 2001 1.8t 5speed VW Will Not Engage In Any Gear
Jan 7, 2015
I recently bought a volkswagen jetta 1.8t wolfsburg edition 5speed. While driving i switched from third into fourth gear upon letting the clutch completely out the rpms began to spike and no power was being produced. So I neutralized to the nearest stop and tried shutting my car off and restarting it and then putting it into gear it would not engage in any gear what so ever at all. The clutch then had no pressure or resistance in it when pressing down and lets up slowly.
The motor stilll runs perfectly fine and the actual shifter will move into gears in the gear box but the clutch still has no pressure and doesn't even attempt to catch or engage in any gear. Do i just need to replace the clutch or the intake or the flywheel or what? In addition i have since ran the code runner and nothing comes up besides the intake code but that's because i took the intake off to manually try and engage the clutch into gear witch still did not work.
View 2 Replies
Advertisement
I'll start this off with a few months ago, I went on a trip and along the way noticed that the car wouldn't get into gear. This happened for a few moments, and solved itself.
Fast forward to a few days ago:
So, my Golf MK4 AUTO 1.6L transmission doesn't want to shift into 4th, sometimes.
One and two are good, but sometimes I get quite a lag in between disengaging 2nd and getting 3rd also.
Furthermore, sometimes I get 4th 'semi' engaging, where the engine is revving too much to be fully in gear, but I get power to the wheels and accelerate (slowly).
I did a VAGCOM scan and got the old:
00652 - Gear Monitoring
27-10 - Implausible Signal - Intermittent
I also had a CEL on my dash, which I cleared with the VAGCOM. This removed the light, but of course the error still persists.
I've been reading around, and some people have said the issue is the TCM, but some people have had similar problems and a TCM replacement has not fixed this.
(Just btw, my TCM model is 01M927733LK).
And some people have had good results with solenoid replacements. So, I was thinking of doing a ATF flush, just because it was recommend on some posts, but won't necessarily fix the problem.
Contacted a garage to do this for me (never flushed automatic tranny before) and mentioned the VAGCOM codes, and he said this is a slip code.
So, now I'm not really sure what to do to fix it. Are the solenoids interchangeable? Am I able to switch two gears' solenoids to see if it moves the issue to another gear, proving its the solenoid?
View 1 Replies
I have a problem with automatic tiptronic transmission my golf MK4 TDI 1.9 2001, it dosent engage on 4th gear when i am driving, the codes that I received for this foults:
01316 - ABS CONTROL MODULE
49-10 No communication- Intermittent
00652 - Gear monitoring
27-10 - Implausible Signal - Intermittent
View 3 Replies
So I just replaced my clutch. I have a 2001 Gti vr6. It has roughly 120,000 miles and the clutch went out. I ordered a stage 1 clutch and put it in. Everything went smoothly and now I am stumped as to why I can't shift into first, third, and reverse? Second, Fourth, Fifth all work. Why this happened?
View 8 Replies
My buddies Jetta won't shift into high gear. I am going to take a look at it this saturday to find more out.
View 4 Replies
I just picked up another GTi and knew the transmission was iffy when I bought it. I had to deal with the serpentine belt tensioner which is now new and also a new waterpump since it was wobbling.
I've already drained and replaced whatever oil was in there with VW G60 Gear Oil which is what my Dealer here told me to put in and it shifts smoother now but still has the same issue. I also did the Shifter Cable adjustment to see if that was the problem but that only made it easier to shift but it still got stuck.
Basically what happens is when driving I shift into 3rd gear and when I go to shift out of 3rd it comes out of gear but it's like it hits a brick wall and will not go into the home position. I was hoping the adjustment and new oil would work but it hasn't done anything.
View 2 Replies
Got a 2001 Jetta 2L automatic 200k miles with gremlins. possibly multiple unrelated problems. First problem that presented is that the transmission will occasionally not shift into 4th gear. I discovered that if I stop the engine, then restart it, it will again return to normal operation, hence the thought that it is electrical. After a year or so of this, second problem pops up: the engine will die while the car is driving, or some times idling at a light. I've also noticed that the interior lights flicker somewhat in intensity when on and the engine is operating, so there could definitely be a grounding issue somewhere. I have heard that the ECU/ECM connectors could become corroded, but haven't yet dug into it to look. Any guesses as to where to begin?
View 2 Replies
01 jetta vr6 5 speed. Alright so earlier today I pulled out the driveway. (Hard) was in 1st gear around 3 or 4 grand and I stomped it. Got to 6 grand and hit 2nd. Took 2nd to 6 grand and let of around 60 mph. After that I short shifted into 3rd, 4th, then 5th. I noticed going into fith was hard. Had kinda rev match to get it. I stayed in 5th till I got to my destination roughly 4 miles. When I came back out to leave I had a hell of a time getting it into reverse. On my way home it was extremely hard to shift and now when the car is running I cant get it into any gear. This is what I did.
Car shifts fine with car off.
Car will not shift with engine running.
When started in gear with clutch depressed I can still let the clutch out and stall the car.
When starting car while in gear with the clutch NOT DEPRESSED the car jumps forward.
I can figure it out ove tried re adjusting the linkage. Nothing.
View 6 Replies
My problem(s) are as follows:
I recently got a 2001 VW Golf 1.8T from a buddy in the Marines. He delivered it to me at my home almost 4 hours away, as described, reportedly without any issues. I got all of the paperwork transferred so that my wife could have a solid daily driver, only to discover ...
1) The vehicle in question was apparently used by a car audio company local to him, who has done some serious screwing with the electrical system in order to incorporate (and then remove) their crap.
2) When shifting through the gears, and coming to 4th gear, you get a couple of seconds of initial acceleration, followed by deceleration and RPMs falling, which in turn leads to the speedo dropping.
3) The same thing happens in 5th gear.
4) The only option is to downshift to a lower gear, which she did, and was apparently cruising along at 60 mph in 2nd gear, as 3rd gear was behaving the same way as 4th/5th upon downshifting. I'm not a mechanic by any means, but I'm pretty sure this is a BAD thing .
View 9 Replies
Just wondering to diagnose the noise my manual 2002 is making when I engage a gear.
Generally, it'll clank every single time I put the gear in gear. I.e. clutch down (quiet), shift into gear (clank), lift clutch up (clank).
Very annoying; has been happening basically since I bought the car (but obviously not when I test drove it!)
I do not think it's a motor mount, especially since I wouldn't think that moving the gear into gear (before lifting clutch back up) would cause the motor to shift enough to make the mount clank. If at all...
Anyway, here is a link to a YouTube video I've uploaded. Every time you hear a clank, I'm simply lifting the clutch to engage the gear. I do this quite a few times going forward and backward. [URL] .....
View 3 Replies
Our 2002 Elantra (automatic, 57000k) seems to have a blown transmission. A few days ago, it sounded like the car was "whining" and then it was having difficult time engaging next gear and eventually check engine came on and the car stalled. Firestone said it's a transmission problem.
We've had the car for less than 10 years so technically this should be covered under their powertrain warranty but I have a strong suspicion that the dealership will find a reason to not honor the warranty. It's still below 60k miles so we really didn't have to replace transmission oil.
View 5 Replies
The problem started with a front seal leak a few months ago which I had no choice but to continue driving with because of low funds. I don't drive much so a couple of quarts of ATF was usually enough to get me out and about for what little driving I had to do. I know.. a front seal is cheap, but I'm partially disabled and unable to work on anything that is not under the hood.
I finally scraped up enough money to hire a friend to replace the seal, but he had a life crisis before completing the work, so I had to get another friend to reinstall the trany... still had the leak, but I could get around by adding ATF as before.
So we tried again... dropped everything and put another new seal on. This stopped the leak, but we got some grinding/squealing noises and could not get the trany to engage any gear.
From reading forum posts and other sources, we decided to replace the TC which we just completed this evening. We got some more of the grinding / squealing noise like before, except that it only occurred the first time we tried cranking the engine, the 2nd time we got no noises, but again no gears engaging.
What to check/replace next assuming there is something we can look at other than a total trany rebuild or replacement. I personally find it hard to believe we could have gone from a tolerably functional trany to scrap metal just replacing a seal and the TC. Its gotta be something simple we overlooked !!
View 9 Replies
OK, so for the last few days it gets harder and harder to get into 1st, the rest are fine. Now it will not engage at all. If it were cable, shouldn't it also have problems in other gears? Even with the car off and clutch out, 2,3,4,5,and 6 all go in and stay just fine. First gear feels as if there is a physical blockage. Thoughts?
View 6 Replies
MKIV jetta GLI, first two gears just won't engages as if it's still in neutral. Have to start her moving from 3rd. What could be the issue?
View 14 Replies
My AC doesn't work right now, however, sometimes it works. It's very random, it doesn't matter if its hot outside or if its cool.
What happens is my AC clutch doesn't engage. when I turn ac on, it raises the idle for a second, and as soon as it does that, my ac compressor gets around 12 volts for less than a second, and the idle drops again. it does that in a loop.
My fans work fine, both high and low speeds, everything else works, all the fuses are good. I changed the pressure switch, didn't fix the problem. I also checked the ac coil and clutch. everything clicks and works. ground on the compressor is good.
Other odd thing - positive wire on the compressor constantly getting around 3 volts. What can it be and what else do i need to check?
View 24 Replies
I have an 02' 2.0 Jetta Wagon, and the A/C is having some issues. Since I know close to nothing about A/C systems, I took it in to a few places to have it looked at. I've had the whole system Evac'd and recharged, and have had the low pressure fitting replaced (apparently there was a slight leak there), and the system is still not working.
The A/C worked fine when I first purchased the car a few months ago. Shortly after my 800 mile trek from Oregon, back to home, the A/C started to only work intermittently. The compressor would engage, then disengage, repeat...It seemed like a bad idea to keep trying to use it in its sad state so I stopped using it altogether. As I said, I had the system emptied and recharged, but it still only works intermittently. It sort of follows a pattern where upon start up it works longer, and switches on and off at shorter intervals, until it doesn't engage at all.
There are no strange noises from the compressor, and when it was hooked up to the machine, it proved to be performing its function well.
View 5 Replies
Compressor does not engage, and my fans do not come on when I turn on the A/C. They do come on low speed when I jumper pins 1 and 2 on the temp switch plug, but they do not come on high speed when I jumper pins 2 and 3.
I have replaced the FCM with a new one, as well as a guaranteed working used one; neither one changed anything. I assumed right away that it was the fcm because my original one has a hole eaten through it from battery acid.
Compressor clutch ohms out within spec, and it will engage if jumpered.
View 3 Replies
I have a 2002 Jetta 1.8t and the A/c doesn't work. I took a look and I know that the clutch/compressor does not engage. also, the rad fans do not turn on when I have the AC on in the car. all I get is hot air. I tested the line and there is no freon in them whatsoever. which is why the compressor is off. however, I can't add any freon without it working. I checked the fuses on the side of my dash and on top of the battery as they seem to be ok. Also, I was told that I just need to replace the compressor with a new one and I should be good to go. Is this true? It will be an easy fix if it is.
View 13 Replies
AC went out last week, was working great earlier that day. Checked under the hood and the clutch isn't engaging. Noticed an RPM spike every four seconds or so at idle when the AC was on. Checked voltage coming off the wires that go to the clutch and saw a voltage spike from essentially nothing to 9-12V which occurred in sync with the RPM spike. I poked a screw driver in the high pressure port and got a nice blast of coolant so I figured refrigerant isn't the issue.
Fuses are all good, in car and on battery. Replaced the fan control module and now there's no RPM spike and I get a constant 12v with the AC on at the clutch wire, but it still doesn't engage.
It's a 2000 Jetta 2.0 auto.
View 6 Replies
03 Jetta 1.8T AC is giving me fits. When the compressor comes on the AC is nice and cold. Problem is that it isn't on very much. Today was a good example. No AC for about the first 30 min drive to get an oil change (local driving). Next 40 min highway drive, AC only got cold for the last 20 minutes and then started to warm up before I got to work. Drove to auto parts place at lunch, AC cold from start to finish. No AC all the way back to work.
So, this evening I started the car with the hood up and watched. Compressor wouldn't engage. Pushed the AC button a couple of times and clutch engages. Compressor stayed on for 7 minutes and ice cold air. Clutch then disengaged and immediately both fans went to high speed for about 5 minutes with warm air out the vents.
Fans cycled back to low speed and compressor clutch engaged again for about 2 minutes this time. Fans to high speed again for 3 minutes, then compressor engaged for only a minute. Each time the compressor shut down, both fans would go to high revs. The minute they would go to low speed, the compressor clutch would engage and I'd get nice cold air..
Just had the expansion valve replaced and r134a charged by and AC shop last week. I have had the on/off AC problem for months and then could not get the compressor to engage at all for about one month. Of course, just as I was getting to the shop, it started blowing cold air.
Not sure whether I'm looking at an electrical problem or what. Just seems odd that both fans suddenly speed up and slow down and the compressor engages only on low speed.
The only other odd thing I've noticed is that cold or hot, as soon as I turn the ignition on (engine off), one fan continually starts cycling on and off. It does that continuously. I've checked the fuses on top of the battery and they all look fine. No appreciable drop in RPMs when the compressor engages. Fan control module?
View 7 Replies
I had to replace one of my Ac lines. The skinnier one.I have never seen the air work in this car. That line was broke since I have owned it.
I went to try and fill it today with r134. I have as much pressure on the low side as I can put in. (55 says the cheap gauge) But when I turn the car on the clutch does not engage to cycle the freon so no cold air. What I know,The fans do not turn on when Ac button pushes.The connector to the compressor only read 4v. I cannot get any number on the high pressure switch connector. (3 pin)
I don't know if it just doesn't turn on because nothing in the high side? Is there a way to bypass? I read jumping the switch is a bad idea.
View 2 Replies
