Picked up another gti vr6 5 speed for my girlfriend. It needed the control arm bushings replaced. Finished up and went to drive the car. Now when in gear and let of the clutch. Makes a terrible sound and won't move. But speedo goes up .
View 3 RepliesJust got my car back from the shop and it squeaks pretty loudly at low speeds. It seems pretty clearly to be coming from underneath the front seats and it sounds like rubber rubbing against steel so I am guessing its the control arm bushings.
Yesterday I took it to the shop to have the passenger side control arm installed and to have the tie rods done and get an alignment.
This past weekend I installed new drivers side control arm/ball joint, front struts (also installed a new rear hub & wheel bearing). I did not hear any squeaking after I did that.
Is this just something that needs to be broken in?
It wasn't til I got it back from the shop that it started to squeak. I only notice it from 0-20 mph then it seems to go away. Everything else seems fine, suspension, steering and alignment are all great and there's no clunking etc.
Front lower control arm bushings are completely separated. Looking to upgrade in some way to poly bushings or some other sort of performance setup.
View 4 RepliesYesterday, i bumped into the curb as I got home, and today when I went to work the car is pulling very hard to the right, and makes a squeeling sound when I get up to speed. The ball joint looks bad, but can that cause this problem?
View 4 RepliesBrought the Tig in for an oil change & while it was on the lift the tech noticed that the subject bushings are cracked/separating...Tig has about 43,400 mi...is this a common issue?
View 6 Repliescan you replace the upper control arm bushings (pass side) with the arm still in the truck?
View 8 RepliesMy rear control arm bushings are cracking. I was wondering if this is a serious problem and what negative effects it will have if I leave them alone.
View 10 RepliesI bought a used 2007 Lexus RX350, FWD, in December 2012 and had it looked over before I signed the papers by a non-biased mechanic. He said the control arm bushings would need to be replaced in the future.
When I took the car in last month to my mechanic (a private mechanic, not a Lexus dealership), he said the control arm bushings on the right side are worn a lot more than the left side. He said on this Lexus, it would require removing the engine to replace the parts (?) and that because it was such a labor intensive job, and the left will eventually wear, that he advises I get both the left and right replaced at the same time.
MILEAGE: 65,000
Last time I was in, the shop replaced my sway bar links, which had already been diagnosed and the repair scheduled. Then, after replacing the sway bar links, the mechanic told me that the control arm bushings were cracked. They already put new struts on the front, as well. So I asked him what else was going to go wrong with my suspension. He said nothing else should need work. He also said that the car was safe to drive for a couple months but I definitely needed to get it fixed.
QUESTIONS:
Is it normal for a car with 65,000 miles to have cracked bushings? I realize that the car is 11 years old; I just wondered how much a car's mileage plays into cracking the bushings and, if so, after how many miles should one expect before cracking occurs.
Does it sound like they're trying to soak me? Why tell me one thing at a time? Perhaps more revenue from the labor side of things?
Assuming the bushings truly need to be replaced, does the community here think there is anything else that should be checked and taken care of at the same time? It is both costly and annoying to have to take the car back numerous times.
We've got a '96 aerostar (4x4). The bushing and upper control arm seem to need replacement but the parts seem to be obsolete. Any source for these (other than salvage yards)?
View 14 RepliesSo I swapped out the PCV valve while changing the oil in my '02 civic and upon driving I noticed a faint rattling/buzzing sound. I only notice it at idle, whether because it goes away when I accelerate or because engine noise drowns it out. I grabbed my stethoscope and to my dismay found it to be the PCV. It's not loud, but loud enough that I noticed it was out of the ordinary.
Now, I've read conflicting things all over the internet. Some people saying its perfectly normal operation, while others saying its a sign of a defective product. The old PCV was pretty gnarly, but did just barely passed the shake test.
Car has a little over 100K. How to replace the bushings on the suspension arms. Took my car in for the brake switch recall and was told my bushings were cracked. Not sure which ones, but I assume all of them. Looked online for a DIY, but not for the RX330. From some of the DIY's I've seen so far, it looks like a bit$! to replace those rubber bushings.
View 14 RepliesI have a '92 Aerostar XLT with a rear control arm problem. The bushings have worn out and the rear end floats side to side as much as 1 1/2 inches. Ford says one bushing comes in the arm ( no longer avail ), one is a press in (no longer available), and the other is like a strut bushing and is available but without the other 2 there is no point in replacing the one. How to fix this enormous problem???
View 10 RepliesI have a 2008 Honda Pilot less than 80,000 miles on it. was just told by the dealer the control arm bushings need to be replaced. They put it on the lift for me and I saw what looks to be dry rot on the bushings. I am the original owner and it has not been abused .. all required service completed.
View 4 RepliesSo I just but my golf about a month ago and have hit many problems but the most annoying is the hum I get at 3500 rpms. In my searching I feel somewhat confident this is caused by a cheap right axle replacement. I also went under and found on the left axle markings that indicate its is oem VW and I was unable to find these on the right side. anyway I have found this: [URL]....
It says it is a hollow axle right there and it is 170 less than the cheapest oem one I have found. would this workout?
My 2004 Golf GTI VR6 6-speed manual makes a louder than usual decelerating noise while in 2nd, 3rd, and 4th gears. If I give it gas it doesn't make any noise but once I take my foot off the pedal it makes a louder than usual decelerating noise. It sounds almost as if something is maybe grinding but I'm not sure what it is. One mechanic said it may just need to be serviced (new transmission fluid). I've read some forums saying it may be the bearings or maybe need a new transmission. The car runs fine otherwise and there aren't any problems shifting up, it shifts really smooth. '
Its only when I downshift that I hear the noise. The noise is the same no matter if I'm turning or going straight and and it's in neutral, there ISN'T noise. It's only while in 4th, 3rd, or 2nd while decelerating. Even if this is a common problem with VW's how do I fix it?! The previous owner said it's been the same way since he's had it and it has NOT gotten worse and his mechanic said it was nothing detrimental to the car so he left it that way. The GTI has 130K miles on it and runs strong, that's the only problem it really has. I'm not sure when the transmission fluid was last changed so that could be a possibility. Going to possibly try that in a few days and see what happens.
So I keep hearing about how the DSG makes a unique sound when you manually downshift.
View 14 Replies2005 jetta. On the highway when I hit about 75mph I hear this loud humming coming from either the engine or the exhaust, I'm not sure. It disappears immediately once I cross about 82mph. What could this be? Why such a specific range?
View 2 RepliesI have an 03 2.0 jetta manual shifter. Never had issues before this morning. Got in car and sounded like it wanted to turn but wouldnt turn over. After a few attempts the turning sound stopped and I heard an electric pop. Now engine won't even try turning when I turn key it just clicks and engine makes a high pitch noise. Took starter and battery out got both tested and they are fine...
View 3 RepliesRecently had this problem which started up about a week ago where my car would make this clicking noise whenever I turn left while driving. When I turn to the right there is no noise. Some said that it could be that CV joints need to be replaced. I have a video showing the side that is making the sound, maybe there is something abnormal that I don't see.
[URL]
I have an 05 GLI and it makes noises when it's off. I don't know what it is. It's a 4 second hum then kicks off.I don't know if it's a pump of some sort or what. Today when I opened my car door for the first time of the day it did it. My **new** battery dies a lot. I've always thought that I've just left stuff on because I am a ding dong.
View 5 Replies