Golf IV / Jetta IV :: Hard To Shift When Car Warms Up On Hot Days
Jun 10, 2014
When it gets hot outside and the car warms up (15 mins or so of highway driving), the stick gets extremely hard to move and it doesn't go back to center when it's out of gear. So I could push it all the way left or right without putting it in a gear, and it would stay there, it wouldn't pop back to the center like it should. It becomes really annoying and difficult to drive because it gets so stiff and hard to move, what could be causing the problem? I've already adjusted the shift linkage and that didn't work.
View 3 Replies
Advertisement
I bought a 2003 Ford Ranger, 2.3, 5 speed manual. It is hard to shift after it warms up. I test drove it when it was below freezing, so I didn't notice it at first. The warmer the day and quicker the truck warms up, the worse it is. It goes into gear with no problem when the engine is off or if I'm still moving, but if I'm stopped there are times it is hard to get into gear. This really sounded like a clutch that wasn't fully disengaging to me, so I decided to pull it apart. I didn't check the movement at the slave before I started, but I did find the master was a little wet at the rod in the cab.
So, I did the following:
- New clutch master cylinder (system bled out of truck to eliminate air)
- New slave cylinder and bearing
- New pilot bearing
- Changed transmission fluid - Mercon III ATF
I inspected the clutch/pressure plate and it was in good shape and looked like it might have had 10K - 20K miles on it. The last owner said it was recently replaced and it looked it. So, I put it back in. After I was done, I checked the movement at the slave/pressure plate and it is moving about 3/8" - 1/2" when the pedal is down. I was happy and thought this would solve the problem since the old pilot bearing seemed stiff and I saw the leak on the back of the master cylinder.
I drove it and all felt fine at first, but it was a cool day and I didn't drive it that long. When it was warmer over the next couple of days, it started getting hard to shift again. It's not been quite as bad as before, but still doesn't shift right.
View 12 Replies
I have a 1999 GMC Suburban(5.7) with 173k miles. When the outside temperature is above 80 degrees F and I have been driving for about 30 minutes, I get a hard/firm shift from 1st to 2nd. It shifts to the other gears normally. When the temp is below 80 degrees, I can drive all day without any problems. Any clues for what may cause the hard shifting on hot days?
View 2 Replies
I've noticed now that it's winter that my Legacy with 14k on it will shift somewhat hard into drive from reverse if I don't let it idle and warm up for 2-5 minutes before setting off. After that one shift, the car is fine the rest of the day. I checked the transmission fluid and it appears full, I had a more mechanically inclined person check also and it looked full to them as well. It seems more pronounced if I parked on my hill with the front of the car facing up the hill - but i use the parking break to hold the car, and release it before starting out.
The issue is if I just go - sometimes it will jerk into drive - one time even though I've learned to back up, come to a complete stop, wait a second, hold the break down all the way and then shift into drive, it jerked forward some distance over the breaks, but then stopped. This only happened once - but it happened with my father in the car, so it was a bit disconcerting... It happens before I even touch the gas...
This is the 5 speed automatic with a manual mode and paddle shifters - I'm just using the fully automatic R and D.
Now, my family likes Subarus and has owned a number, and my last one, an 07 impreza with automatic sometimes jerked into drive also, and my relatives have sometimes had that happen with Autos. Is this just a Subaru traditional Automatic thing? I spent many hours with my 07 in the dealer for this, only to be told it was normal, so I'd rather not waste everyones time again with the 2012 Legacy if it's just "a subaru thing". I can certainly live with warming the car up when it's cold, though that seems to not usually be a best practice with modern cars.
View 1 Replies
Over the past few weeks, my car (2002 Golf 2.0L) has gotten really hard to shift into 1st and reverse (has crunched once or twice), but only when the car is hot, after driving it for a little while. When this happens, and I try to shift into reverse, the shifter feels really "sticky" and can get kind of stuck in the depressed position near reverse.
I bled the hydraulic system and replaced the slave cylinder, but no dice. I haven't noticed any clutch slipping. Shop wants to replace the whole clutch. Is this the right answer?
View 5 Replies
My 03 Gli 24v manual transmission has been acting up lately. First it started to get a little difficult to shift into gears about a week ago. Then tonight i was driving through a parking lot in 2nd, and after i came to a stop i tried to put it back in to first and it would not go into gear. As i was trying to get it into 1st i could tell it was grabbing a little bit and the car was inching forward.
I got it to a parking spot and starting reading about other peoples issues, one i read said they were able to get it to move after pumping the clutch some. After trying that i was able to get it into gear and drive it to my parents. Looked at my brake fluid and its full. Took it for a test drive around the neighborhood and it was shifting fine at first then started getting a little difficult to shift again. I tried taking off in 6th and it stalled. I tried going from 1st around 3k-4k rmps to 6th and it was still driving with very little lugging. My clutch feels and is still stiff, not loose at all. I do have to go all the way to the floor with the clutch before im able to shift
Finally to my questions. Could my clutch be going bad? Could my cables need adjusting? Something I read about a pressure plate maybe?
View 5 Replies
01 jetta vr6 5 speed. Alright so earlier today I pulled out the driveway. (Hard) was in 1st gear around 3 or 4 grand and I stomped it. Got to 6 grand and hit 2nd. Took 2nd to 6 grand and let of around 60 mph. After that I short shifted into 3rd, 4th, then 5th. I noticed going into fith was hard. Had kinda rev match to get it. I stayed in 5th till I got to my destination roughly 4 miles. When I came back out to leave I had a hell of a time getting it into reverse. On my way home it was extremely hard to shift and now when the car is running I cant get it into any gear. This is what I did.
Car shifts fine with car off.
Car will not shift with engine running.
When started in gear with clutch depressed I can still let the clutch out and stall the car.
When starting car while in gear with the clutch NOT DEPRESSED the car jumps forward.
I can figure it out ove tried re adjusting the linkage. Nothing.
View 6 Replies
So I changed transmission fluid on my 1.8t GLS because I was having difficulty shifting out of gears on cold starts. It seemed to work fine for a few days and now I'm back to square one, it still doesn't want to shift correctly!
View 14 Replies
Background facts:
Tranny swapped from my 4 speed auto to a 1.8t o2j 5spd
13lb. Light flywheel
Powerflex dogbone mounts
Peloquin LSD
The problem: Very hard to get a smooth shift from gear to gear. Trust me, I know how to drive, but I can always feel the car shifting into a different gear if you know what I'm saying. On my friend's bone stock Jetta, I just let the clutch out without gas in between shifts and you don't feel a thing.
On my car, you feel EVERYTHING. People have told me the light flywheel will make the ride more uncomfortable in many ways, especially since the RPMs drop much quicker in between shifts than stock.
View 9 Replies
Today I had planned on replacing coil No. 5 to rid myself of the rough idling and drive I've been experiencing the past couple weeks. Car is running smooth now, however, I've noticed again that coolant continues to leak at a fast pace on hot summer days.
I've always had a slight leak, about the size of a hockey puck or so if I let it sit over night. But once temps reach in the mid 80s-90s, like today in PA, the leak gets even worse. Pictured below is the amount of coolant that had dropped in about an hour span. I have attached an image and video of where I can see it dripping from. It looks like it may be a hose, but I can't tell if the coolant is just dripping on there initially from somewhere else, and then onto my driveway. I don't have a jack that I can get it high enough to check.
Car specs:
2003 VW GTI VR6 24V 98,000 miles
View 7 Replies
It happens mostly after the engine warms up. When I accelerate, I hear a weird cranking noise coming from under the hood (sometimes it doesn't happen). I popped the hood to see if there was anything wrong, but i didn't find anything major (there were 3 loose screws that I tightened because I thought they were causing the vibration but the noise persisted).
I doesn't make the sound when I rev the engine, only when I am was driving. It happens roughly between 1500 and 3000 RPM. I read some of the archives to get a few ideas, but the noises people are describing are not like the one I am hearing from my car. The closest thing I found this: [URL] ....
I made a video. You'll hear the noise the loudest when I first start pressing the gas, from a complete stop: [URL] ...
View 15 Replies
My issues: when I'm on gear 1 for example, on hot days, and only on hot days ( 25 deg.c and more) when I put it on neutral it suppose to go at "home" position ( i think this is how you guys call it, like align with the 3rd gear) But it stays align the the first.
Same with all the gears. It's stays aligned with the gear I just left.
View 3 Replies
So i was trying to adjust my freinds shift linkage on his o2j and i got a little ahead of myself and forgot to put the shift tower in the home position before making the adjustment. after i realized you can't shift into second ( either that or 2nd and 4th are extremely close together now and feel like the same gear ). I try to get it in home position even with the cables off ( did this for experimentation) and still wouldn't go into home position...meh. still have all the other gears including reverse .
View 4 Replies
My 03 Jetta is having transmission trouble. It will shift from 1st to 2nd but wont shift to 3rd. It is an automatic 2.0.
View 10 Replies
Long time listener first time poster. My wife has a 2009 Vw jetta 2.5 with a manual transmission that is very hard to shift. It has 80,000 on it and has had the clutch replaced once. She told me that she never had any problems shifting until she let it sit for two weeks while she went to cape cod. I have driven it myself and can confirm that there is an issue. Sometimes it just will not go into gear. No grinding noise at all and very very stiff when moving the stick shift laterally from first to fifth. Not actually shifting from 1-5 just moving the stick across the range it feels like cement. I have already changed the transmission fluid and used the Vw oem oil. I also removed the shift boot and lubed all the moving parts with a high quality grease. Tomorrow I am going to bleed the clutch slave and have a good look at the shift linkage. Is their something I am missing?
View 5 Replies
I went on vacation for a week and left my car at my parents house. I came back and now it has become extremely difficult to shift between gears. It's nearly impossible to get the car into reverse, extremely difficult to get it into first, makes a thud when pulling it out of first, is semi difficult to get into 2nd, but only a mild nuisance to get into 3rd through 6th.
For more information, the car is a 2012 Volkswagen GLI with just shy of 40,000 miles. The car ran just fine before I went on vacation and the car was not moved while I was on vacation. I did notice that a little ticking kind of sound when I had the car in neutral with no clutch. So the throw out bearing was starting to wear, but it was a very slight. But I haven't had any other problems.
View 13 Replies
Having shifting issues with their 350? I have a 2014, AWD F-sport and ever since I got it about 4k miles ago, it's been sluggish to up-shift until the engine warms up. It commonly takes me 2 or 3 flicks of the paddle (or stick) to upshift into any gear and this is during very easy acceleration too (I would never romp on it until the engine is fully warmed up).
I would at least understand if it was on downshifts as maybe a way to protect the engine from revving too high when it's cold but it's actually doing the opposite by temporarily preventing me from lowering the revs. I've also always had a car with a manual transmission so I don't know if this is typical for shiftable automatics or not but it seems weird to me.
View 10 Replies
I just finished the DG install yesterday. I am having a real problem with the first gear: it is really hard to shift into it (I mean hard!) - and several times I went into 3rd believing it was in 1st, while driving. I know that the DG is notchy and a little stiffer (which I like) but this does not feel right. I have to really push hard (moving slightly toward reverse) to shift into 1st. My wife would never be able to find it or shift into it (not that I let her drive my R that much...).
Note that all the other gears (2,3,4,5,6 and reverse) shift beautifully without any effort with that nice click. But not 1st.
What is it? Adjustment? I did it twice. I made sure that both cables were "all the way in" before tightening the first two bolts (and I made sure that the cables were not moving - a common problem with this install) with the engine lock on and pin in.
View 22 Replies
2011 TDi 6 Speed (Sportwagon) with problems shifting into 2nd? Mine is currently in the shop under investigation for a balky shift when cold. The tech says it's not right, but then they find another vehicle in inventory with the same issue...currently waiting on a VW engineer.
View 16 Replies
Today, driving the car around town it was suddenly really hard to shift in/out of first when the car was stopped. Driving, no problem at all. Then within the ~15-minute drive, it got progressively worse.
Got the car home, checked and noticed that my HPA short shifter was wearing out (the splines), so I threw on the stock piece and figured everything would be ok... not the case. Here's what's going on:
- When the car is off, I can shift through all gears easily (and into the proper gears as far as I can see.. which tells me that shifter alignment should also be fine)
- When the car is off, and (for example) I have the car in 1st - I can let off the ebrake and the car doesn't roll (it's in gear), when I press the clutch, it will roll
- When the car is RUNNING, I can't shift in/out of any gears at all. This morning it was just really tough, and it was actually easier if I didn't have the clutch pedal all the way to the floor.. but now I can't at all if the car is running
- No signs of anything leaking under the car
- The car is APR Stg 3 and I have about 50k miles on a stage 2 clutch. Prior to this, I didn't notice any slipping, weird noises when shifting, etc.
Sound like either master/slave clutch cylinder? Or more like a clutch issue itself?
View 11 Replies
My 2000 Camry --4 cyc has a problem with the shift lever on hot days. It is hard to move from P to R to N to D and the other way back to P. There has never been any liquid spill on it. In cold days, the lever shifts fine.
View 2 Replies
