Come out to the this am and notice a small puddle that was not there last night. Pull the car out and it's start burning something off. Roll the car in first thought is oil (maybe the turbo return line is leaking) no its coolant. On the lower portion of the down pipe and running across the bottom. I'm at a loss as where the leak could be coming from being back there.
View 6 RepliesMy 2000 Jetta 2.0 has a coolant leak. I searched and found a lot of mentions of the flange on the driver's side, and I have coolant dripping from the bottom of the car in a location that seems consistent with that, but I felt all around the flange and the hoses that are connected to it and it feels dry.
Where else could it be coming from? (yeah, I could jack it up climb under and look, but I haven't had time yet). I also seem to have an oil leak around the same location, but the dipstick tube was cracked near where it went in to the engine so I'm hoping that was the source of the oil.
I have coolant leaking from the bottom of this hose on my brothers car. I am not very familiar with the BEW's as I drive an ALH. Just looking for info about part number or name on this hose so I can get a new one. Has a part number MH3364 on it but that is not working anywhere.
View 2 RepliesI have a 2002 V6 Passat Wagon. I am hemorrhaging coolant out of my lower coolant pipe. I can reach it put my finger in a feel the coolant coming out as fast as I pour it in. I can't see any way to get at the pipe from the top and I can't see the hose that should be attached there from the top. I assume this means the front end will need to be jacked up and go at it from the bottom. Also note the intake and return from the heater in my car is mexi fixed and looped together (no heat).
View 2 RepliesI have a 1999 jeep cherokee 4x4 four liter inline 6. have a coolant drip at bottom radiator hose, change hose. but still drip. Could water pump be leaking. and it running down on the bottom radiator hose.
View 4 RepliesI have a leak on the right side of the cross over pipe. I removed one long bolt from the right side and two long bolts from the left side that go through the thermostat housing, and three bolts from the back of the alternator, but the pipe doesn't seem to want to move. I don't want to break anything.
View 2 RepliesAbout a month ago, I traded my 04 V6 for an 07 V6. Everything was fine except that this morning I turned on the A/C for the first time (had been in Econ) and what happens? Condensation on the lower portion of the windshield just like in the 04.
View 3 RepliesI just bought a 2004 Jetta and noticed the bottom of the engine does not have a lower belt guard... I can just see the serp belt spinning. I feel like there should be some kinda guard to protect it from Weather and debri? It's a 1.8T.
View 4 Replies2014 fx4 6.2. Had a coolant leak. Brought to dealer for warranty work. Found a leak in middle lower tube area. Said they replaced radiator part # BL3Z-8005-D. It sure looks like my old radiator still under the hood complete with squished bugs. Am I missing something?
View 2 RepliesJust had to replace radiator at 38k on my 2012 SD. Now I have another leak at 41k. Looks like it's wherever the lower radiator hose leads. Kind of a weird junction. I don't think it's coming from above there, but not sure. It's the primary dgas bottle that was low. The radiator was covered under my ESP. We'll have to see what's up with this one. Been eying a denim blue SD at dealer, thinking this is going to talk me out of it though. Not especially happy right now.
View 3 RepliesOK so my 2001 F250 was leaking power steering fluid from the lower portion of the gearbox (where the pitman arm attaches).
I found a thread on this forum where it showed how you could change the seals out WITHOUT taking the gearbox out.
So I got the pitman arm off with a heavy duty puller. Then I scraped out the 1st rubber seal hoping to reveal a snap ring behind it. Well, the seal is 99% scraped off, but there is not evidence of a snap ring. It does seem like there is some metallic ring holding another rubber seal in behind it. But again, I can't find the little open spots that you put your snap ring pliers in to get snap rings out.
How do I get this metallic thingy out???? I already broke a small drill bit trying to drill it out. It just doesn't seem like the best way to go about it.
I'm trying to troubleshoot a leak on my 08' F250 with a 6.4 powerstroke. It's been dripping coolant when cold pretty aggressively. Once the truck heats up, the coolant leak seems to mostly go away.
Here's a picture of the drip, it's marked by a dart, so you can see the location from the top (second pic). The radiator house connection around the engine seems dry.
Pic from Top ....
What's hidden here that could be causing the leak?
My car started make a weird chatter noise. The noise was never there before I swapped out the plastic coolant pipe with the billet crack pipe.
Car info : Stock flash, flapper open, EVOMs intake, 46k miles
I have a 2004 1.8t Jetta with a rusted out flex pipe. The leak is causing a bad smell and also a lot of noise -- What's my best option to replace the downpipe (but also other parts if need be) without having to weld it?
View 6 RepliesI installed the non-resonated exhaust, but I noticed that some air/water condensation is coming out of the small pipe that join the cat and non resonated part of the exhaust.
I double checked the position of the small part and is very deep inside the other tubes, plus I checked the clamps too.
I have a '02 Jetta Wagon with 180k miles. The plastic coolant pipe on the side of the head had been weeping (as they do) and I decided to replace it last night. The pipe replacement went smoothly and uneventful. When I removed the pipe as usual a normal amount of coolant spilled from the head down onto the trans area. After the replacement, I hosed down the top of the tranny with the garden house. I then took the car out for a drive.
First thing I noticed that my CEL was off (it had been on for a small emissions leak) and that seemed odd. Then about quarter mile down the road I noticed she was not shifting. It would hit maybe 30 at 3000 rpm and just stay there. So I pulled over and turned her off and looked under the hood...all seemed well. Started it back up and the CEL comes on right away. I drive and still stuck in gear.
I get home and run a cheap CEL check and get 00281 and 00652. Which seems to be fault codes for the VSS G68 sensor. So I check my connectors, take apart and make sure they are clean and dry...all seems good. I clear the codes and start it up and codes are right back again and stuck in gear.
It is late so lat thing I do is check the resistance of the G68 and get pins 1-2 800ohm, pins 1-3 800ohm, pins 2-3 1600ohm. I also check pins on G38 and get 1000ohm there.
So I did the seafoam trick and I came to the conculsion that my exhaust leak is coming from either the manifold or the flex pipe. There was no smoke coming from under the car only a mist of smoking coming up from the back of the engine, probably by the manifold or the flex pipe. I do not see any visible cracking per say. I have attached a picture of the end of the flex pipe and it almost looks like someone may have tried to seal it before? I don't know if that is normal or not as seen in the picture.
2002 Volkswagen Golf 2.0 ...
2006 F350 4X4 .. How in the heck do you get to it? I have that massive heat shield in the way and can't get a shot at even those bolts? One bolt left to get out then I can start going back together.
View 10 RepliesI noticed pulling out of the garage today that my car is leaking oil. It looks like it's all getting on the lower splash shield, then dropping out the back from the passenger side. It's leaving about 8-10 drops a night it looks like.
View 2 RepliesAfter buying and installing the low temp thermostat, fan switch and green top sensor, I'm still encountering boiling in the line and a temp of 3/4 of the way when at idle. My coolant mixture is about 70/30 and unfortunately I had to use a temporary fix of the prestone universal coolant mix due to the dealer being closed and I didn't want to add more water
What would be the disadvantages of running straight g12 coolant? My issue is boiling and I figure the more coolant and less water, the less chance of boiling to occur.
I have an 04 Excursion with a 6.0PSD. I am currently experiencing a coolant leak, not very bad at the moment but I would like to fix it. The coolant is running down the back right side of the engine and I can see coolant pooling on the pan on top of the motor, specifically the right side. I can see some moisture on the front of the engine but it is below the top of the engine and I do not think this would be the cause since coolant won't flow up hill. I can't see or smell any coolant flowing when the engine is running but see it at idle and when parked.
View 5 Replies