Golf V R32 :: Coolant Temperature Gauge Needle Stuck Dead On 190f - Code P2433
Apr 27, 2016
The needle has always stuck dead on 190f when it gets up to temp. About a week ago I took the center grill of to paint, I put it back on and the check engine light came on ... code p2433 secondary air pump problem. I figured I had just disturbed something etc. Now the coolant gauge is going up to around 240f during normal driving, the fan stays on for about a minute when I turn off the ignition.
View 16 Replies
Advertisement
I recently had the radiator on my car replaced and wen I got it back the temperature and gas gauge needles are both blown past the HOT sign and past the full sign on my gas gauge and is sitting under the little black piece under the the cold side and under the empty side. it was obviously messed with and completely turned around but why is it like this? will it reset itself or should I take i.e., back to the mechanic to have it fixed by him?
2000 buick park avenue....
View 9 Replies
Car is a 2012 GTI 6MT with APR intake.
Within the last couple of days, my engine temperature gauge has been acting a little strange. The needle will fluctuate depending on if I'm accelerating or at speed. I've actually seen it go down several times before going back up to normal temp. On a couple of days, it will go up to about halfway to normal temp, and just stay there for a lot longer than it usually seems to.
There have also been times when the car is at normal operating temp, I'll go into a store for maybe 15 minutes, and when I come out, it shows the engine temperature is maybe halfway to where it should be. Then it will go back to normal after a few minutes of driving. I would think that if the engine is warm, it should stay there for more than 15 minutes, even if the car isn't on.
We haven't had any abnormally cold days lately, and I'm not getting any CEL, but I was wondering if anything to worry about, or if it's normal.
View 11 Replies
Was on my way to my girlfriend's house and decided to do a few pulls. Noticed afterwards my rpm gauge was stuck at 6k rpms and wouldn't go any lower. The car was running fine and I was in 6th gear just cruising at 55mph. Did another pull and after that it was stuck at 8k and if I downshifted the needle would max out at the 6 o'clock position. When I arrived I turned my car off to see if it would reset itself and it got stuck at 7k rpm.
View 15 Replies
Ok I was driving home right know from work, and looking at the speedometer, i notice that my temperature gauge turns off (the needle goes all the way down). what can it be?
View 2 Replies
Resurrecting my 940 TD after it's been sitting for a year and the temperature needle now doesn't rise as the engine warms up. Is there any trouble with sensors on these or should i be concerned about something else? It was working when I stopped using the car.
View 3 Replies
The needle is moving up and then back down. This mostly happens while at a stop and simultaneously the ac compressor kicks off.
Recently new radiator and temp gauge, plus coolant flush.
View 8 Replies
My car recently turned over 120,000 miles. I have owned her for 5 years. Currently, the engine temperature gauge needle is moving all over the place. It typically registers the correct temperature (I think), but sometimes it goes all the way over to the red, then peaks and falls back down to the midline.
Before this started happening, the needle would lie just below the midline when traveling on the highway and just above the midline when driving in town. Yesterday, it was lying between the 1/4 mark and the midline -- much lower than normal. Is this as simple as just replacing the temperature sensor?
My mechanic noticed a month ago that the transmission hoses are all swollen and in need of replacement. Is this related?One more thing, within the last week, the electrical system fails while driving, but just for a second. I can tell because the radio goes out. Once, it went completely dead, then came back on within 2 seconds. It made me think of the alternator, but it seems if that were the case it would go dead and not come back on, no?
View 8 Replies
Last fall I had my radiator flushed and at the same time my coolant overfill canister with built in temperature guage sensor was replaced with a new unit. (The service station replaced the resevoir canister with a new unit in the engine compartment, because they felt the sensor is prone to failing after 7 years.)
Ever since, my temperature gauge needle on the dash will randomly drop (even when the car is up to FULL OPERATING TEMPERATURES) showing the engine being cooler than it out to be. In other words the needle drops signifying to a much lower water temperature. After a period of time the needle will recover back to the normal full operating temperature mark on the dash gauge.
What could cause this? Inside my radiator do I have a "diafram" temperature valve that could be failing /"sticking?" In other words could a temperature valve in the radiator be sticking at odd or random times??? I also notice that my heater does not put out the usual full furnace heat that a Passat is know for. The temperature is about 1/3 cooler now that we are into winter temperatures.
Is my heater core clogged?
Could the new coolant sensor in the new coolant overfill chamber not be working well? This whole situation began AFTER my radiator was flushed, and AFTER I had the coolant reservoir canister and sensor replaced.
View 6 Replies
This weekend I was one a trip in my '98 Civic, and I noticed some movement in my temperature gauge. It didn't really overheat; the needle never got near the red, but it did go a little higher than usual.
Normally, once the engine heats up, the needle on the temperature gauge doesn't move, not even a little. It sits right under the squiggly lines on the temperature gauge icon. However, on Friday, when I got off the highway, the needle rose into the upper part of the icon, to the part with the thermometer.
As soon as the car started moving, the needle on the temperature gauge went back to its normal spot, so I assumed it was a problem with the radiator fan and I kept on driving, prepared to turn on the heat if the needle on the temperature gauge started going up.
Saturday morning I took the car to a local shop in Jacksonville, and it turns out the engine needed a new fan and a new thermostat.
The first lesson that comes to mind is that keeping an eye on my temp gauge might have saved me an engine. It certainly saved me a head gasket. Since a head gasket or new engine would have been worth more than the car, catching this before it became a problem saved me from having to buy another car.
The next lesson is that my Civic had two things wrong with the cooling system, and yet it barely showed any symptoms. The air conditioner doesn't work I guess since a working A/C would probably have made it overheat. In any case, I've probably been driving without a working radiator fan for some time.
The final lesson is that if I had tried to diagnose this myself, I'd probably be driving around with a new radiator fan and a bad thermostat. I paid about $435 for a new fan, thermostat, and fresh coolant (I declined the cooling system flush) and it was worth every penny.
View 5 Replies
The needle in temp gage on my 2005 Toyota is now facing the opposite direction. This happened right after the most recent oil change. Is this a gauge or a sending unit problem?
View 11 Replies
I am having problem with the gas gauge I have a full tank of gas but the gauge needle is stuck on E but when I unhook the battery and hook it back and start the car the gas gauge needle is on the full and its stays on full for like 3 days and then the gas gauge needle will drop back down to the E and stay there. This sound like something wrong in the fuel pump.
View 2 Replies
The temperature gauge in my 2006 S60 2.5 T suddenly stopped working and I noticed that the cooling fan was stuck on relatively cool Michigan weather. In addition I also noticed a 2-3 mpg reduction in average fuel economy and a reduction in overall power. I did a little research and found that the 2006 2.5T models had an ECT recall. Turns out the ECM was telling the engine to operate at overheating conditions,due to a faulty ECT.
Picked up a new Engine Coolant Temperature Sensor (OEM is recommended by most authorities for replacement sensors). I replaced the ECT without even removing the engine cover, it didn't fix the problem at first. Then I pulled the fuse for the ECM, a 5 amp fuse in the box mounted on the drives side fender, and let the ECM reset for a few minutes. Then, had the temp gauge back, and had peak engine performance at operating temperature.
View 3 Replies
Last night I went to drive my car and my coolant light went on. I checked the overflow and it was very low. There was barely any left in the overflow. I thought this was strange because I had just checked the coolant a couple days ago. The coolant that was in my car was an orange color (after searching I realized that I think this is g12 which I was unfamiliar with). Before searching I added Prestone 50/50 pre diluted green coolant. The bottle said it was mixable with any type of coolant color or kind. After reading more threads I'm seeing that I think the g12 just contracted with the cold weather and I should of just left everything. I have barely driven the car since adding the prestone. Am I doing harm mixing in the prestone? If so, How can I fix this?
On another note, With the cold weather my temp gauge seems to be acting a little funny. Once the car is up to operating temperature the gauge will then drop around 40-50 degrees. It will then stay like this while im driving, but then will go back to normal once the car is stopped and running.
View 3 Replies
I have replaced radiator and thermostat, awhile back.. I checked and there is antifreeze in the radiator and the reservoir. I don't drive it unless i really have to. and not to far,lots more work to do on it. But the coolant light started blinking the other day. Temperature gauge inside is ok. What could this be? what should I do? Still haven't got the blower working, heater / ac / defrost.
View 5 Replies
I have a '99 1.8T Passat. The coolant temperature gauge normally reaches operating temperature of 190 degrees within about 5 minutes and stays there. For some reason, after reaching 190, it sometimes drops by 20-30 degrees and is running cooler than normal. Once time it dropped down, then came back up again, while driving a steady 65 mph. The coolant level is full and nothing else has changed.
I guess there are a few possibilities: a thermostat stuck open too far, a failing temperature sensor, bad gauge, or loose connection at the sensor. The car has 145K miles and the thermostat and water pump were replaced at about 100K miles. What is going on? If it runs a little too cool, is that a big deal? How would I diagnose it? Where is the temperature sensor?
View 2 Replies
I was driving and noticed that my temperature gauge went close to the warning zone so I blasted the heat and it went back down. When the car cooled I popped the hood and noticed that the coolant reservoir was pretty close to full but I couldn't see any coolant in the radiator. I filled the radiator with water for now but it looks like it gone again. I cannot spot any actual cracks or leaks on the hoses but I did spot a puddle of coolant in the groves on top of the transmission. The closest hose I can spot next to the puddle is the lower radiator hose but I really do not know too much about cars. I also noticed a hissing sound today coming from the radiator cap, which I am going to replace. Where the leak could be which is causing the puddle on top of the tranny?
View 4 Replies
Temperature gauge quit working after changing the thermostat and coolant.
With the engine off, I disconnected the single wire from the temperature sending unit and switched on the ignition without starting engine. The gauge pointer stayed in at the Cold mark. Using a Jumper wire, I grounded the sending unit wire and the needle on the gauge went to the Hot mark.
I quickly turned off the ignition, and replaced the sending unit with a SW-2328 (F1SZ-10884-A) Temp Sender. Warmed up the engine, but still no reading on the dash gauge.
View 8 Replies
Basically my coolant temperature gauge either reads as the hottest it can be, or the coldest. It doesn't jump around a whole bunch, but it's always all the way to one end or the other. From what I've read there seems to be a lot of different temperature sensors, so I get a little confused with all of the abbreviations, but I'm fairly certain I checked the correct one, next to the thermostat housing.
Using a multimeter I checked the resistance of the sensor, and it was around 600 ohms about 30 minutes after it had been driven. I'm not sure if this is where it should be or not, but it was rising as the truck cooled off.
Anyway, I'm not sure if I just tested the sensor incorrectly or if there could be another issue. A friend of mine suggested that the thermostat may have gotten stuck or something, but it doesn't seem like the gauge would switch at all if that were the case. What I should check to try and fix this.
View 7 Replies
2005 Hyundai Tiburon Keeps Overheating
I live in Washington State and have a 2005 Hyundai Tiburon with less than 110,000 miles. I have had it for 5 years, and have not had any issues with the car until recently (last 2-3 months). My car overheated on me back in May while out running work related errands. I was able to leave it parked downtown while my husband took a break from his job to come pick me up. Since then, it has continued to overheat every time I drive it.
The temperature gauge climbs into, or dangerously close to, the “red Zone” within the first 10 minutes of driving. The first couple of times the car overheated, if I was using the air conditioner, it would start blowing hot air instead of cold air and the air would stay hot. Now when I drive the car with the air conditioner on and it over heats, it continues to blow cold air (if that matters at all).
My super handy husband (a certified motorcycle mechanic) has done the following in an attempt to fix the car:
•Checked coolant levels
•Topped off coolant
•Bled coolant system and added yet more coolant
•Replaced the thermostat
•Replaced the radiator cap
•Water pump was replaced November 2012 (not even a year old yet)
The radiator cap was the most recent fix. It was replaced on a Wednesday evening after testing it and finding that the existing one was not maintaining the proper PSI. The car drove great around town for two whole days without any issues (Thursday & Friday). Saturday, I decided to take it on a longer drive out of town to see if my good luck would hold…it didn’t. I drove a total of 30 miles round trip and my car started overheating after about 20. I limped back into town and barely made it back to our apartment.
My car continues to overheat!! What is going on?! So confused and frustrated I’m hesitant about taking it to a mechanic who, my husband is convinced, will just charge me to check all of the things he has already fixed.
View 7 Replies
2002 ford sport trac.I have been having an ongoing issue that started with the engine cranking but would not turn over until an hour passed. After replacing multiple parts (cam shaft sensor, crankshaft sensor, ignition pack) I am now down to poor fuel economy as the last of the issues (roughly 12 in the city and 15 highway). I was told the issue may be the engine coolant temperature sensor going bad so I decided to replace it. I found this was very difficult due to it being a plug and locking pin design and in a very tight spot in the engine.
I tried to purchase a replacement and the parts store kept trying to insist on selling me a part with threading. I finally found someone that figured out the issue and found the part for the 2001 sport trac had the same plug style with clip that did fit but was shaped a little different on the sensor end which I assume was due to being aftermarket. I noticed that there were two plugs side by side and the one easiest to access was on the left and I was told the one on the right was the sensor that gave the temperature reading to the gauge.
After installing the engine coolant temperature sensor I found the temperature gauge on the dash now will not respond and is sitting below the cold end of the gauge completely off. Is it possible this is because the part was for a 2001? Is the sensor on the left (passenger side) the engine coolant sensor?I would hate to put the old sensor back in just to test if that's the issue due how difficult it was to put that locking pin back on. What to check that could resolve the gauge issue before pulling this sensor back out?
View 3 Replies
