I have a 2001 NISSAN Frontier that the hi-mount third brake light appears the be going out. I've trie to remove the plastic light bezel but a clip is holding in the connector. I'm afraid to use too much force while pushing in the clip with a flat head screwdriver but that is the only thing I know to use. The lights are dim and seem to flicker as the brake pedal is pressed.
View 1 RepliesI have a 2004 Nissan Frontier with V6 non-supercharged engine, 4x4, with manual transmission, 150k miles. For approximately the last 30k miles, I have had a persistent shuddering in the cab when I apply the brakes slowing from about 15 to 0 MPH. It is accompanied by a low humming noise that decreases in pitch as the truck slows down. It only happens when the brakes are warm; about 70+ degrees outside or after I've been slowing down a lot. It does not seem to correspond to engine temperature, only my perceived temperature of the brakes. There is no pedal feedback, and it does not shudder when I stop using only the parking brake. It does not seem to affect stopping distance.
I first tried to fix it by doing a very thorough front/rear brake job - new pads/shoes, new rotors/drums, and repacked front wheel bearings. That had no effect on the problem. I tried rotating the tires and that had no effect. I then did a complete front end job and replaced all the bushings and balljoints via brand new pre-assembled control arm assemblies. I also replaced the tie rod assemblies, sway bar bushings/end links, and had an alignment done. That had no effect.
Based on the repairs I've done, I would assume that it is having to do with the front brakes, but is not warped rotors or anything in the front suspension.
I have a Nissan 98 frontier 4wheel drive 4 cylinder king cab. I just changed the windshield washer pump and since then the brake and battery indicator lights stay on. I disconnected the battery and that didn't work. The battery checks out and I could find the switch for the parking brake to check it. Sounds like a short in the wiring harness somewhere.
View 7 RepliesI have some rust building on the heat shield of my cats on my 2001 Nissan Frontier.. I had a weld done to keep it from rattling after replacing the OEM muffler. It there anything I can put on it to retard the rusting process on the shield and will that affect my emissions?
View 4 RepliesI have a 2001 Nissan frontier SE the 6cylinder, no turbo, automatic transmission. My wife was not paying attention and thought the truck was running and so she put it in reverse and then realized that the truck as not running so she tried to start it while in reverse, when that didnt work she put it back into park and when she tried to start it, the cd player restarted and the wipers started and the guages peaked and whe truck made a fast ticking sound. i thought that it may have some how killed the battery but it does the same thing with the new battery in.
View 3 RepliesI have a 2001 Nissan frontier and the air hasn't been working for a while now. So I need to know how many cans of freon does it need?
View 6 Repliesmy 2001 nissan frontier xe is making squeaking, slipping sounds past couple months. getting more frequents, scaring me to drive and felt like has brief loss of power couple days ago while parking.
someone told me power steering fluid is orange rust colored and gunnky and needs replaced which i dont know how or have tools for.
Video of it here. At around 1 minutes 54 second, and 2 minute mark, among others, the sound is audible. [URL] ....
I have a 2001 Nissan Frontier Crew Cab XE with a V6 (without the supercharger). I bought it on Halloween night with only 42,000 miles. It now has 112,000 miles on it. I moved from Georgia to Kentucky and heard that I needed to have the cooling system flushed/filled to prevent it from freezing in the winter time. I then noticed that it would periodically "overheat." The temperature gauge would climb up to the line just below the "H" and then I would turn on the heater.
I read online about a "bleeder valve" on top of the intake manifold. I loosened it, squeezed the radiator hoses to get all of the air out and then tightened the bleeder valve. I then let it run until the thermostat opened, revved it up to 3,000 to let all of the coolant flow. Now, at various time with no specific reason, it will run fine and then just "decide" to overheat.
I can drive it on the interstate for fifteen minutes, park it in front of my house and then have to "tack it up to 3,000" just to get it cool. I've changed the thermostat and had the water pump tested. Neither of them are faulty. My mechanic vacuumed out all of the air from the system with a special tool the dealer recommends using and it still does the same thing. What's going on with this vehicle?
I have a 2008 nissan frontier SE 4x4 with 71K on her. I'm getting two codes from my checking engine light P0455 and P0447. The gas cap is new and tight.
View 3 RepliesI have a 2004 Nissan Frontier pickup that I bought used in 2012. Shortly after I purchased it the the check engine light came on, would go off and back on. Last year (before inspection) I hooked it to the diagnostic auto scanner and it read the error as four oxygen sensors. The truck was running fine but in order to get it inspected I ended up changing all four sensors. The light came back on within the week (as soon as it rained) then would go off a few days later. Rain--on, then off. I managed to get it in for inspection on one of the days the light was off. So, now it is again inspection time. Light is on, still error on the scanner as oxygen sensors. Light has not gone off in a long time.
Also noting here that I have checked this error on several different scanners. The truck is running fine. Before I take it to the dealership is there anything else this could be?
I have a 98 frontier 4 cil. 4x4 manual transmission. The CE light is on telling me that the evap system needs work. I replaced the purge canister valve and now the light wont go off at all. You can clear it all you want, as soon as the truck starts the light come back on.The truck also runs rough, bucks at certain RPMS has no power and bad gas mileage. Within the last two years I have replaced; catalytic converter, fuel filter, plugs, wires, cap & rotter, transmission and clutch, air filter, cleaned the MAF sensor.
View 11 RepliesI have a '99 Nissan Frontier 4cyl. p'up and the air conditioner kept going off. The truck has three drivebelts, all inline. The first is Crankshaft to the Power steering pump , the second goes from Crankshaft to the water-pump & the alternator and the third one goes to the air-conditioning compressor; the one that keeps coming off my truck & shutting down the A.C. I replaced it three times and the last time it went off within a couple of miles. I know the crankshaft and the A.C. compressor pulley's are out of line and believe that's my problem. A mechanic friend of mine looked at it and said he thought it was something called a belt-leveler that keeps all the belts from slipping off.
View 2 RepliesI bought the car 3 years ago 2003 2.4L Hyundai Santa fe , I have driven it around 200 miles ( to and from shops ), I am having an issue now where once the car is warmed up ( post 15 mins ) It will idle really low * almost stalling * and oil pressure light will flicker, If I hold the brake and get it to almost 800 - 1k RPM it goes off and driving is not an issue *no knock*. I just got it driving for the 1st time in the past year, and drove it for about 45 mins in stop an go traffic, Temp light was all the way to cold, once stopped in stop and go traffic it would go up half way, as soon as I could get above 50mph it would slowly work itself all the way to the bottom?
More Information
2003 2.4L Hyundai Santa fe
I should really count my losses and move on but I cant.
Bought the car with 89K on it I now have 90K
New Battery
New Radiator
New Motor mounts 3
New Trans mount 1
New Hoses
Oil Change ( 40 miles ago )
Trans Oil Change ( 40 miles ago )
Power Steering Fluid change ( 40 miles ago )
2nd cat delete ( didn't want to waste any more money )
After Market 1st Cat
100k 2.0D .... Recently when pulling up at roundabouts or junctions either at low speed or quite rapidly, the engine oil light flickers. This doesn't happen at all on idle no matter how high it is revved and never while speeding up or at high speeds. I have tried to narrow the time it happens and just ended up being confusing because it can happen slowing down while in gear with engine under strain or to a lesser extent while coasting with g/box in neutral at idle speed.
The engine oil and filter has been changed but to no avail (as expected). I could check the oil pressure sender and wiring but it doesn't make sense as why the fault is not sporadic and quite consistent when it happens. (Also I did look at trying to remove the sender unit and possible fitment of a pressure gauge but how the *BEEP* do you get any tools to that!). I did mention it to a friend who knows a pair of mechanics at a local garage who both straight away went *ooooh sounds like big end bearings!!*
It's a 2000 Frontier V6 4x4 CC with 104k miles. It just randomly dies going down the road. Sometimes it restarts. Sometimes it doesn't. Sometimes I just get a small blip (loss of spark or fuel - unsure which) when going down the road then it's fine again. It seems seems like a loose connection somewhere to me but I have checked and repaired everything I can find.
A little history of problems...
Fall 2014 - Fuel Sending Unit; I had similar problems a little over a year ago and I replaced this at ~90k miles. The stock one was corroded and the fuel pump wasn't getting power. Got the part from Nissan directly. Truck ran great for a year then started having same issues in fall of 2015. I am thinking this couldn't have gone bad again in only a year, but who knows? No engine codes at the time.
December 2015 - Distributor #1; I replaced it with one from Auto Zone. Had the same problems that day. Returned that and replaced with one from Napa Distributor #2 (New - house brand - supposedly made by Altrom - which is supposedly comparable to OEM) This seemed to fix it for a little while. At the same time I did the timing belt, spark plugs, wires, valve cover gaskets, a bunch of suspension work, etc. so I had the harness off. Did I knock something loose? I feel like I have checked it up and down.... doesn't seem that way.
January 2016 Bad Wire?; Same issues. Wiggling the harness into the distributor seemed to have an effect on restarting so I pulled the harness apart from the dist to the main and found a small cut on the casing of one of the ground wires. The wire was not damaged, just casing. Fixed that with a double layer of shrink tube and it ran fine again for a couple weeks. In this same period my catalytic converters also went bad. My exhaust manifolds cracked, next thing I knew I had catalytic converter codes on both sides of the engine. Ran it like this for a few months.
April 2016 Distrbutor #3 Same problem. Randomly dies. Gets progressively worse over a couple day period. I gave up and took it to a shop (Downing St. Garage in Denver, CO) They diagnosed it as a bad distributor so I had it replaced AGAIN (they were nice enough to use the Napa part I bought and get a free warranty part)
June 2016 Distributor #4 Same problem again. Still have not replaced cats - did not want to spend the money when the ignition problem seems un-related. Replaced distributor with another warranty part from NAPA. This time the one that I took off made a crunching sound when you turned it by hand.
August 2016 Finally replaced cats. CEL codes were gone for an afternoon then the truck started sputtering down the road again... CEL P1320 and CEL P0325 BACK AGAIN!
I am at a loss on what to do. I have read that the MAF sensor can get dirty... but this doesn't seem to explain the P1320. Anyway, I ordered some cleaner, a new knock sensor and another distributor (this time Nissan brand but re-manufactured... they no longer sell new ones.)
Our mechanic is stumped. The Frontier runs hot when idling. The clutch fan and thermostat have been replaced. The radiator has been flushed. When you are driving or you turn off the A/C, the temp goes down. The next suggestion is to replace the radiator, but I'm already hundreds into this so I hate to do anything else unless I'm pretty sure it is going to fix it.
We do know that the catalytic converter needs replacing. Could this have anything to do with it?
When I cut off the engine by mistake (shift slip ie ) the restart comes around but only after about 5 to 15 minutes . The last time this happened the car was at an intersection and this situation is getting dangeous.Why is the restart taking so long ?
View 2 RepliesI have read two other threads that indicate a leaky head gasket for Nissan Frontiers overheating...but I'd like an opinion on my problem: I have a 1999, v6 3.3L, 4x4, manual Frontier that I have owned since 2001, always well-maintained, timing belt, water pump and thermostat already replaced a couple of years ago; currently has 129k mi. I rarely drive it (about once or twice a month).
Last time I drove it (I'm in AZ and heat was over 100 degrees) it started right up and was fine until I'd gone about 3 miles on the freeway doing about 65mph. Started to climb in temperature, but not into the red zone. I drove with it hovering just above the midway point (midway meaning perfectly normal temperature on my gauge) for a couple of more miles, when it started to climb just a bit more, I got off the freeway and dropped under 45 mph, the temperature went down to normal. I drove about 40mph back home and haven't driven it since.
I checked my coolant, which was extremely clean and not low, and was not boiling when I checked it soon after the temp went up on the freeway. What is the most likely cause?On a side note, since I do not drive it that often, what is recommended as to the gas that has been sitting in my tank since? How long does the gas stay good for? Further wondering how often it is recommended I drive it, for how long and at what sustained speed to keep my truck up and running?
I have a 2000 Nissan Frontier that is a 4X4 and has the V6 engine. Mileage is 172,000+. For a few years, I have had problems with the AC no longer cooling after I drive 20 or so miles and stop the truck, go in a store and start back up only to find that the AC will not cool after the stop. This seems to happen more when the weather is hot. Only once has it gone out without stopping the car and it was on I40 driving trough Oklahoma in 100+ degree weather. Once it quits cooling, after driving 20 to 30 minutes, it usually starts to cool again. It sometimes speeds up the process if I roll the windows down.Coolant levels are fine.
So...is there a faulty sensor somewhere? What could it be that is the problem?
We have a 2003 Nissan frontier pickup (automatic).The AC recently stopped cooling, but the fan works. It was cooling perfectly great when all of a sudden, it stopped. If we turn the AC on, the compressor (I'm guessing) starts to click and continues to click until turned off. (started to grind under hood). It's not a rattle, definitely a click as if it wants to turn on but can't make the electrical connection. It kind of sounds like when a starter has gone bad and it clicks. Except, it does it repetitively until turned off. This doesn't happen if we turn on the fan but leave the AC off. Does it sound like the compressor went out? How can we troubleshoot it?
View 19 RepliesI have a 2000 Nissan Frontier that is having issues. I had the distributor replaced and the knock sensor. The day I got it home it started having a weird starting issue. It has always started first crank super easy & strong. Runs GREAT.
When the truck is cool it starts right up but, when I've been driving around for a bit and turn it off, if it's a short stop starts right back up, some hesitation. If I stop for 15-45 mins it doesn't want to start. I can crank it all day and it wont start and gives a little kickback, if I crank too much the engine will smoke a bit, spits and sputters when you turn the key off. The longer it sits before I try to start it the worse it gets... around one hour is the worse. - Finally figured out if I try cranking it over several times, turn off the key and wait literally one to two minutes it starts right up super quick and strong just like when it's cool. So random and weird.
No warning lights & Nothing shows up when hooked up to the computer, fuel pump checked out OK.