Passat (B6) :: Metal Grinding Noise At Low Speeds?
Jan 23, 2007
Ok so 11 days into ownership and only slightly over 800 miles the car started to act funny. First the common DVD nav issue (no disk in drive message).
Second issue is a strange metal on metal rubbing noise when turning at low speeds (i.e. in parking lots). When I make a big turn (either direction) it sounds like either the brake calipers aren't releasing fully and is causing the pad and disk to rub, or something else is rubbing.
This actually happened once yesterday on the highway as well. going 75mph, a very loud metal on metal rubbing noise.
Seems to only happen when temps outside are below 40. It warmed up yesterday afternoon and the noise went away, but after it got cold again last night, the noise came back.
View 6 Replies
Advertisement
I commute 180 miles a day, 6 days a week. I noticed metal on metal grinding noise(more noticeable) at high speed above 75mph especially on asphalt road. I'm sure noise is there at low speed but not enough to notice. My car has 50,000 miles. Tires? Electric motor?
View 7 Replies
I have an '02 Taurus. For the last year or so it has intermittently produced a metal on metal grinding noise while failing to start up. I'm told this is due to teeth being missing on the flywheel between the starter and the transmission. It's taken as many as six tries to get the car going. But the car has always started in the end.
My questions are: Is the problem flywheel worth replacing at this point at this price? Is it likely to fail totally any time soon?
Also, might the March '09 replacement starter be implicated?
View 5 Replies
I have intermittent metal on metal grinding noise. Seems to happen when I am at highway speed. Seems to go away when I put it on 4 wheel drive or slow way down. On one occasion though, the grinding noise did not stop even after putting on 4 wheel drive - had to stop completely before it went away (did not come back after I drove off again). Diagnostics so far....
Unhooked the vacuum lines on passenger side actuator and hooked up vacuum gauge. Vacuum held at 20 psi and drops and raises slightly as the truck is being revved. Takes about 10 seconds for vacuum to drop to zero once truck is stopped. Putting it on 4 wheel drive drops it to zero immediately. Exact same scenario on the passenger side.
This leads me to believe my IWE solenoid is ok. So also my check valves. Next opportunity I get, I will raise one wheel, remove the vacuum line on that wheel and apply vacuum with my pump. Want to see if it will turn my half shaft.
2004 F150 FX4 ....
View 7 Replies
I have a 2011 Prius with about 32K miles on it. I've been hearing light metal on metal grinding noise for a few days now. So I decided to take it to a stealership and they told me my ceramic pads and brake rotors both need to be replaced for all 4 wheels. I thought Prius brakes don't need to be replaced for 100K miles.
View 7 Replies
I have a 2013 Passat TDi SE with about 64000 miles on it and 20 rims. I noticed a grinding noise when turning right at low speeds. It was a very slight noise at first, but has gotten louder over the past 1-2 months. The grinding noise sounds like it's coming from the back of the car and only at fairly tight turning radii, with speeds 10 - 20 mph (think going up the levels of a parking garage). What could this be????
Other things to note:
No other noises, vibrations accompany the sound.
I do get the steering rack creek when turning lock-to-lock, but this sound is definitely not that sound.
I mentioned I have 20 wheels thinking that might have something to do with it. They don't rub at all going in a straight line, however.
Sound is only present when turning right.
View 4 Replies
I replace my brake pads and rotors in the fall of 2015 with EBC parts. Now almost 13,000 miles later, I started hearing grinding and metal-on-metal contact in the front. So I went out and got PowerStop pads to replace the EBC (EBC had way too much brake dust). I took off the front wheels and noticed that the DF pads had about 1/32 left on them, ok I guess its time to change them out. Onto the PF pads, I find that there is almost no material left, in fact I could scrap off what was left of the material. I decided to do a rotation while I am at it and noticed that the rear brake pads on both sides look like I never used them!! Is it really that possible to have 2 stuck calipers, both on the rear at the same time?
View 2 Replies
I've read a few posts about the Prius braking system. Just wondering what other owners have done when they experience the metal grinding noise and when brakes need to be replaced. My car has around 67,000 miles. I was planning to take it to a Toyota dealer, although prefer to find a certified Prius or hybrid mechanic at an independent shop.
View 3 Replies
For the last week or so been noticing as I'm slowing down, brake or no brake, a metallic, grinding noise coming from the rear passenger side. Does not sound like a humming worn wheel bearing noise. Its pretty loud, almost clunky and not always consistant. Then the last day or so have noticed it on the right side. At higher speeds....faintly hear a ticking... The car has 48K on it.
View 2 Replies
This morning on my way to work, pulling into the parking lot around 20mph. I hear a metal on metal grinding noise. (almost to the sound of a muffler dragging on the ground type noise). Then that disappears for a bit, hear a loud metal clunk then some high pitched sound. All within say 30 seconds. Definitely coming from the back, but can not tell from which side.
Things I've checked in the parking lot:
Nothing hanging low, exhaust seems in-tact
It doesn't look like the brake shields behind the rotors are bent or touching
Sounds still happening if on or off brakes , on or off throttle.
It seemed to happen only at lower speeds. Disappeared once I got up to 50mph
Just took it out for a drive, that loud metal clunk happened when I put it into reverse, drove around, no other sounds. I just don't have a warm fuzzy feeling that this will just disappear.
View 11 Replies
My car is making metal grinding noise when coming to a slow stop when you are stuck on traffic or going into your driveway. You can hear the sound and feel the sound.
I had this issue a year go and i took it to the dealer and they told me that i need to replace my rotors and my front brake pads.
A year later the noise came back and they told me that i need to replace my pads. I replaced my front break pads and a month later the noise is back. I went back and checked my pads and the pads were still new.
I only hear the sound when braking after driving in a heavy traffic or on a stop and go traffic. I don't hear the sound when i start to drive or driving in a non traffic condition.
View 24 Replies
I have a 2006 Elantra 4 cylinder with only 55,000 miles put on it.
Whenever I accelerate I hear this noise that sounds like a lawn lower under my hood, usually only there until around 45 MPH, then it dies down a bit. It as been getting louder and more....... screechy..... as of late.
Also, when idle, there is a sound that almost sounds like a metal grinding chugging noise. It comes and goes with no real rhythm or timing.
Additionally, there is a metal grinding noise coming from what seems to be my front right wheel area when I make wide right turns, as well as intermittently while driving regularly.
To my knowledge, neither of the motion noises seem to be happening above 45-55 MPH, or they are too soft to hear at those speeds.
View 1 Replies
When driving at slow speeds and when I go over a bump in the road, I'll hear something like the metal part of the wheel scraping something as its turning. Only comes from the front drivers side wheel. It's audible enough that people usually turn to look when I'm in a parking lot.
Took it to the dealer, they 'test drove' it. Said they couldn't hear anything. Then said that whatever I'm hearing is 'normal suspension noise'. So after leaving it a full day at the dealer, nothing has changed. Since when is ANY suspension noise normal? But I don't think its the suspension. What to do? Take it back? Take it to another dealer?
View 4 Replies
I am having several issues. I got the lexus dealership to service my transmission recently. I got it back with a weird smell. It smells like body odor. I had to reach out to hendrick corporate for them to address the problem without charging me. Turns out it was the fluid they used. I could smell the smell from inside if i wasn't recirculating the air. They changed the fluid again and it still smells. Is my transmission doing this because it is too hot?
This smell was never an issue until after the first transmission service. And now I'm hearing a metal grinding sound in 2nd gear past 4600 rpm. It still shifts smooth but 2nd gear might be slipping. Something just doesn't seem right. o yea they gave me my car back with my brakes sticking after stopping in traffic. I took it back and was told my brake pads in the rear lost 2mm in less than 650 miles.
By the way this sound can be heard in 1st but is more prevalent in 2nd. It is not heard in any other gears. And when in sport mode the sound instantly stops when i shift up into 3rd.
View 3 Replies
So I'm doing some work on my friends car he just bought, 1990 gts, rebuilt 5sfe, not sure how thoroughly it was rebuilt, there seems to be a metal grinding noise coming from somewhere in the belts, sounds almost like water pump, belt tensioner, ac clutch, or something along those lines. I don't know much about these motors, anything commonly go out on these?
View 2 Replies
I have a problem! I have only had my 07 gs awd for less than 2 months. I noticed this morning when I turn my wheel all the way to the left or right it makes a grinding or like metal on metal noise. My brakes were done only a year ago, and this noise only happens when I'm turned all the way to the right or left.
View 11 Replies
I replaced my pads 3 months ago. Now I have a metal grinding sound (not squeaking). The mechanic says I need new rotors, and he will resurface the pads. I know I can replace the rotors myself; but do I need to resurface the 3 months old pads? If so; how will they resurface them?
View 4 Replies
A year ago I heard occasional metal grinding noise coming from the front, sounding like front driver side. Sounded like CV joints that I heard before. The mechanic said it's transfer case/transmission problem, so I replaced the transmission but the noise came back a few days later. The mechanic said to drive it for a while and the noise may go away, if getting worse he can fix it since it has 2-year warranty.
Now a year later the noise becomes predicable and easily reproducible, I went back and asked them to check. They said it may be passenger side axle. I am feeling being manipulated.
View 1 Replies
Some of you may have seen my thread on my new car: [URL] ....
Its got just over 500 miles on it and I have noticed that at moderate speeds(40-50), if i turn, I hear a noise in the rear part of my car as if there's a metal ball rolling inside. I've already checked and there's absolutely no loose objects or any objects for that matter.
I checked the spare wheel bay, removed the spare, and found this beauty just sitting. Where it came from or why it was there.
View 10 Replies
I'm going to start tearing into my wife's car this weekend because the bearings are making an awful grinding noise at low speeds, so I feel like this needs to be done soon.
I bought from rockauto new hubs and bearings, but looking at them, it seems like the bearing goes over the outside of a shaft on the hub. Other that than, I'm not really sure how it all goes together until I look.
Just curious as to whether this can be done without a press or any special tools? I have an impact gun and all the sockets one could need, but I don't have a hub puller or bearing press or anything like that.
I've done a bunch of searches but can't seem to really find the answers I'm looking for...
View 1 Replies
The steering on my wife's 2010 Tiguan makes a bit of a grinding/rubbing noise at low speeds? Something isn't right, it sounds the same way my X5 did when the Rack needed to be replaced. It would be strange to have 2 cars needing new racks within the same year....especially since they are both 2010 model.
View 9 Replies
