I have a 2004 Santa Fe 2.4L the check engine light is on and says about the evap canister solenoid. I am trying to located it but I can't find it. So, where would it be located at so I can take it apart and where is the Canister located as well...
View 1 RepliesWhere the EVAP canister purge solenoid is located on a 1999 Ford Windstar with the 3.8 engine?? I replaced the vent valve that is located on the canister itself but cannot locate the purge solenoid valve.
View 2 RepliesA buddy of mine has a 2003 Ford Ranger Edge V6 3.0L, he got the code P1450 the other day and asked me to look at it. Got all the info on what it could be but where ex actually is the EVAP canister and CV solenoid located? And what is the problem?
View 1 RepliesI have a 1999 Ford Explorer with the V-6 SOHC that is stuttering and stalling when I try to accelerate. A very slight acceleration will get the vehicle moving, but anything coming close to normal gas pedal pressure causes immediate stuttering and/or stalling. Check Engine light came on when problem started yesterday.
Where is the EVAP System Canister Vent Solenoid? I bought a code reader after beating my head against the truck all afternoon and got code "P1451 EVAP System Canister Vent Solenoid Circuit Malfunction". My Haynes book says on the left side frame rail... can't find anything along there that looks like it (based on picture from Rock Auto for replacement part) and found some people online talking about it being in the engine compartment on the passenger side...
Just crawled all over the truck and I think I found the charcoal canister, but couldn't trace it back to the vent solenoid... There was something right next to the canister, but again, it looked nothing like the replacement part listed on Rock Auto...
I'm not too knowledgeable about wiring and electrical systems. I'm getting a P1451 code (EVAP Control System Canister Vent Solenoid Circuit Malfunction) on my 99 4.2. I've read that it could be a bad solenoid, bad wiring, or a blown fuse. So far I've;
- checked (and changed) the related fuse
- checked the wiring for damage at the connector
- checked voltage at the connector (12 volts)
- checked the resistance at the solenoid (around 60 ohms)
- actuated the solenoid with a 9V battery (can hear it opening and closing)
I haven't had a chance to check the wiring all the way back up the frame to yet, but I noticed that the ground at the trailer wiring harness has broken off the frame. Would this potentially cause a fault in the upstream wiring? I'm going to slap a new connector on and bolt it back down anyway, but as it's Labour (Labor) Day I'll have to wait for the stores to be open tomorrow.
I just had my 3rd Canister purge valve installed a month and a half ago, and it's already dead.
I noticed while I was driving that it was constantly pulsing after the engine warmed up, and continued to do so as long as I was driving.** This did not seem normal to me (I can hear it in the cab).
The solenoid is burning up and measures open circuit. No codes are thrown during the time it continues to pulse, but when it burned up again, the 3 codes (P0441 Incorrect Purge Flow, P0440 Solenoid Failure, P0443 Purge Valve Circuit Trouble) are immediately thrown? indicating the solenoid is fried.
The system runs a series of tests during normal operation, so if there was a problem with an actual leak or clog, it should show up as a test failure code, but does not. My inclination is that the problem is a sensor.
My check engine light came on the other day, with no symptoms or problems. Today I stopped at the Auto Parts store and had the codes read. They were P0440, P0441, P0446, and P0301. They are for the EVAP system and misfire.
I had read here that one of the codes could be for the gas cap so I tightened it and then, also as read on here, disconnected the negative 12 V battery cable to perhaps clear the check engine light. I was curious.
When I started the car again, I now have not only the check engine light, but the red triangle exclamation point. How would you proceed? The 12 volt battery is around 5 years old. The entire exhaust system was replaced last year.(not O2 sensors though)
The hybrid battery was replaced at 70,000 miles and I now have 110,000 miles on it. I really wonder why disconnecting the battery and reconnecting it caused more error lights to appear? Also, the Auto parts guy said his code reader was fine for my car but I seem to remember here that there may be a special Prius one.
I have a 2004 santa fe with a 2.7 v6. I have had a little misfire issue lately. I had a major power loss with a check engine light on it lasted for just a minute before it settled itself out. Had the code pulled at a local parts store. P0301 so I checked the plugs and they looked worn out. I pulled the upper intake and replaced the plugs and wires plus the upper intake gasket. I cleared the code and that seemed to correct the problem. Two days later, same thing happened. The engine seems to be running fine now. I wiggled the wiring harness to the injector and to the coil, no change in the way it runs. I was thinking it could be an injector or a coil pack.
View 6 RepliesI took my 2008 prius with 183,000 miles in last week to have recall work done on it. they did the following:
1. Accelerator pedal recall
2. Steering shaft recall
3. Hybrid Electric water pump recall
The following day when I start my prius my check engine light comes on so I figure it was something they did on the recall work. I do have a scangauge, and the only code that showed on it was a P1304. I took it back to dealer today, and was told that it had multiple EVAP codes, and that the canister on top of gas tank is bad, and will need to be replaced. They said it was full of gas. They asked me if I stopped fueling car when pump shut off? I told them I always go to next whole dollar. They said to always stop as soon as pump shuts off(but on some pumps they shut off like crazy when pumping gas), I told them to just clear codes, and I would get back with them if I decide to have canister changed. So far check engine light has stayed off ( dealer is about 100 miles away)
My 2009 santa fe with the 2.7 has a check engine light. p2422 evap vent solenoid stuck closed. I replaced the charcoal canister and the light came back on. I replace the solenoid by the throttle body and the light came back on but took longer to set. My wife said that she was having problems filling the tank but when I changed the second solenoid the problem was gone but the light had returned.
View 6 Replies1998 Corolla LD ... Diagnostic tests show that my check engine light stays on due to a charcoal canister. Is this an expensive repair?
View 7 RepliesSo, I have a 2009 IV, and it has about 60,000 miles on it. It's still has it's Toyota Certified warranty.
The check engine light has been going on and off for about 3 months. I hooked up my scan tool, and it says there were a bunch of codes popping up for the evap system. I did the obvious repair and replaced the gas cap (with a Toyota cap), and that worked for a few weeks, but the light came on again.
Since it's under warranty, I took it to the dealer and it turns out the vaccum switch (or maybe pump) for the charcoal canister was bad.
Struck me as a rather strange thing to go bad on a relatively newer Prius.
Anyway, had the water pump recall done while it was there, and hopefully all is good now.
My '04 santa fe 3.5 v6 gls/lx, 79k miles, gas, auto, check light has just come on while I was driving a less than 10 mile journey. How can I check what is wrong. Do I need some sort of diagnostic code checker. Do any national outlets check it for free (Pep Boys or Auto Zone, etc).
Just 5 days ago (about 50 miles only) I had timing belt, water pump, plugs and leads replaced, brakes checked and lubes flushed; BUT not at above dealers. I would rather know what the code is saying before I go back to the shop who carried out the work.
How can i turn off check engine light (hyundai santa fe 2003 3.5) by fuse ? I do not have any code scanner.
View 10 RepliesI recently purchased a 3.5 V6 Santa fe. The Check engine light keeps going on. I took it to a few shops and I am getting the same code. It is the O2 sensor in bank one. (I think the the code was po170.) The light keeps going on and off. All I can find are the same problems with different Santa Fe engines (2.7, etc. )... My SUV has 100,050 miles on it.
View 1 RepliesAfter only 1k miles after purchase my Check Engine light as come on. P0440 and one other (left the paper at work)
I haven't overfilled on Gas, the Gas Cap is completely on (2 clicks), and I haven't OVERLY pushed the car either haha.
The only update was replacing the STOCK filter with K&N Drop In Filter.
I only have 2200 miles on my new 2012 Passat SE V6 and the check engine light came on the other morning. I took it in to the dealer and they found codes P0442 (EVAP Emission Control System Small Leak Detected) and P0456 (EVAP Emission Control System Very Small Leak Detected). The tech says on the work order that he removed and tested the EVAP Purge Valve with a vacuum pump and the valve would not hold a vacuum. The dealer replaced the EVAP Purge Valve under warranty. They say this is the first 2012 passat V6 they've seen with this issue. I've only had the car for 4 weeks.
View 5 RepliesI've had a check engine light on in my 3.5 Pontiac G6 for awhile now. It's an emission code (can't remember what code but evap leak). The solenoid by canister was also tripping a code that disappeared after I changed it. However, the evap code still persists. Last night while changing my oil I noticed the intake air hose to the crankcase had broke at the case and wasn't connected. It's the hose that runs from the engine intake to the crankcase for the PCV system.
I am replacing the hose regardless, but my question is; would the intake hose for the PCV system being loose cause an evap leak code? I am thinking no but it'd be nice if it was that simple.
I have a 2004 Toyota Corolla- the CEL has been on for months- the code is for small evap leakI have tried cleaning rust from filler neck at gas cap- no change. I have had a smoke test done with no leak found.
View 5 RepliesI have had a check engine light go on and off with P0700 and P0741 but since the flush day 3 it hasnt come back on and it was chucking with rpm doing small jumps... but now it does it in the mornings after sitting all night after a few chucks its fine for the rest of the day til the next day no check engine light so far, but transmission flush has worked a lot not as bad as before the flush.. So what else could be causing it? Its a 2006 hyundai santa fe with 274,000 kms.
View 24 RepliesI have A 2001 Santa Fe. The check engine light came on about 3 weeks ago and the car was still running fine up until the last few days it felt a little sluggish. Today I got a little muffled backfire noise. It was like a putting noise if I pushed on the gas to hard to speed up. The car has 95,000 miles on it.The car starts up with no problems and doesn't stall. Its A 6 cylinder All wheel drive vehicle.
View 10 Replies