My Santa Fe has a broken power steering pump pulley. Darn thing broke right around the spindle! I can not find a replacement anywhere. I've tried to find a one new, used and at the upull lots (only one Santa Fe in at Pick n Pull dang thing was stripped clean!). The pump is easy to find but this pulley is a ghost!
View 3 RepliesMy power steering went out a few months ago. No warning, whining, or hiccups. Just stopped working. Installed a new pump today, and it worked great for about five minutes. Bled it out, put fluid in, etc. Took off on a test drive and a mile up the road I went to turn into a street and power steering was gone.
Fluid is still full, belt is still there, no visible leaks. 2004 3.5L V6.
I have a 01 santa fe 2.7 motor. I have read several threads in here regarding the famous pump whine. my pump is making a whine at idle, I have cleaned the bottle and made sure the screen has not restrictions, drained all the fluid, and have inspected the lines for leaks.
With a stethoscope have pin the noised to the pump, the noise travels in the reservoir when I race the engine the noise is more evident on the bottle. I am tempted to replace the pump, but the steering has no issues and operates fine, also no change in the whine noise when moving left to right.
I have a 04 santa fe , which slowly started whining which was diagnosed a power steering pump, when replaced the problem got worse and it became very hard to steer. Steering rack was the next diagnosis, replaced and another new pump. Now its so hard to steer and the whining has returned. Looking in the reservoir the fluid seems to be moving good with no bubbles??
View 3 Replies2010, 5.4L... Noticed a small oil spot under the truck this morning. Took it into the shop after work, we lifted it up, and ran it for 15 min to see where the leak was coming from, and the truck did not leak a drop... until we turned it off. The oil would slowly leak near the power steering pump pulley. But only when the engine was not running ...
View 1 RepliesSo I have multiple issues that all seem to stem from a power steering leak. According to the dealership, the PS pump is leaking fluid onto the serpentine and timing belts causing them to swell. This in turn has something to do with the AC compressor not working but they wouldn't give me details. When I looked at the clutch wheels on the AC compressor, there seems to be a good amount of rust in between the two wheels. I can't say that I trust the dealership because the original owner was bought out by a larger group that is known to just say "replace everything". I usually do most of my own work on my 95 Tacoma, so I'm no stranger to import v6 motors.
View 4 RepliesI need to remove the power steering pulley on a 2001 Toyota Celica GTS to replace the pulley shaft's seal. I've got several pullers, so I figure one of them will work. But, I'm concerned that when I pull it out it could damage whatever it messes with inside. Also, I'm going to try doing this with pump on the vehicle.
View 1 RepliesWhen I started engine, I heard the high pitched squealing noise for 10~30 seconds. The noise was from the power steering pump. The noise changed by turning steering wheel. I did drain & refill 4 times with Preston dino base PSF & turkey baster. Next week cold day, the same noise was still there, so did drain & refill 5 times again with Preston PSF, but the same noise again.
A week ago, 3rd refill was with MaxLife Dex/Merc ATF that I had in my garage, more than 1 liter drained & refilled. Today at -15 C(=5 F), the noise came back for 5~10 seconds. I feel MaxLife(synthetic base) is better than Preston(dino base), but still several seconds noise make me worry about my power steering system.
Am I the only one hear the noise? Is this noise the start of the pump failure? Is this normal for the extreme cold winter?
2001 Santa Fe. 4 Cylinder
It has spark, it will run briefly with starting fluid.
The camshaft, crankshaft, fuel pump and TPS are all good.
All fuses are good.
The fuel pump relay is good.
The FP relay gets power to both the control side and the FP power in side.
If I jump the FP power side of the relay it will get 12v pump to the FP connector.
NO power to the FP cutout switch by the master cylinder.
So, how can the relay be good and the FP get power if I jump the relay but not have power when I put the relay back in? Is the ECU cutting it out as soon as it gets a signal from the relay?
I have a 2003 Santa Fe 2.4. Couple days ago my idler tensioner pulley or whatever its called seized up and took the belt out with it. I got a pulley that resembles it from Autozone mind you that it was the only parts store that had one in stock even Hyundai didnt have the part. The only difference is the hole size for the bolt is about 1/4 inch bigger then the stock pulley. Is there any chance I can get a spacer and make up for the difference?
View 6 RepliesSanta fe 2.7litre 2004 240000km... My santa fe won't start, after check we found no power at the fuel pump. we change pump, we found a bad contact at the remote starter connection. we decide to cut the wires of remote starter. after the car start and ride 1 day, stop with check engine, towing
We take off the remote starter and disconnect all wire of this remote starter. The car start and stop. After that bizarre problem, the park light stay open, and the window can be up and don't with no key in the ignition!!!!
We check fuse relay etc, all wire of the old remote starter and we take off battery and rebuilt the ground. We still have the same problem; when we tried to start at acc, everything seam normal but the wipers run at off position and when we turn the key for starting , wiper stop , radio close.
Like we have a ground problem. We change the ignition little baril now we think the computer is maybe dead. I double check all remote starter wire and every thing seem ok !!!!!
Need to know the thread pitch and diameter for the water pump pulley bolts? The previous owner of the engine I bought clearly didn't know how to get the fan off as the pulley and plastic fan are both loose so I cannot loosen large nut.
View 1 RepliesOh where do I start. 2003 Santa Fe, V6 Auto, FWD.
The engine has been making a loud ticking noise lately, starting right after an oil change it seemed. It actually sounded a lot like a stuck lifter, so I had an engine flush done, but this did not remedy the problem. Popping the hood one day it was particularly noisy, I noticed that it sounded like it was coming from the serpentine belt tensioner (or there abouts).
Anyway, tonight, *something* finally gave. All of a sudden I heard a squealing noise, then smelled burning rubber, and my battery light came on, and I lost my power steering. I figured that the tensioner finally gave out.
I turned off the vehicle to see what I could see. A bit of melted S-belt was it. I restarted it, and the belt was turning fine again, but while it was idling, I noticed that the crank pulley was shifting in and out now and then. When it moved inward, the S-belt shifted in as well, and started to rub on the timing cover, wearing a hole right through it! Have a look at the attached photo, showing the grove worn right through.
So I'm assuming that my tensioner was fine, and it was my crank pulley all a long. I'm figuring that 3 thing will need replacing:
1. Crank Pulley (the source of the problem)
2. Serpentine Belt (since it's probably half melted)
3. Timing Cover (can't see that water getting in there would be good)
Does this sound accurate?
I have a 2003 Santa Fe 3.5 liter. I have a bad power steering leak and the dealership says I need
pressure hose
return hose
cooler hose
I've tried all the local car part stores and Napa has the pressure hose but for about $180.
I am having a power steering problem with my 2006 santa fe, been going on for a couple weeks and I am stumped on what is wrong with it, what I noticed is turning to the left or right and very hard to turn and sometimes it will be fine and other times its the left or right.. What could be going on here? there is no leaks or noises noted, it has 242,000 kms on it. fluid is full but a little brown and smells a bit burnt. I know it will need a flush but would that be the solution or would it be something else?
View 15 RepliesI've got what seems to be a fairly common problem in that my power steering on my 2001 SF gives off a steady whine. I've read in several posts that removing the power steering reservoir and either replacing it or cleaning out the screen solves the problem. I'm ready to give that a shot, but can't seem to figure out how to remove the part. There is a "tab" type of thing on the back of it, but it doesn't seem to do the trick. I'm admittedly no mechanic, but this seems like it should be relatively easy. How to remove the reservoir?
View 6 RepliesI noticed that the power steering fluid is leaking bad from a weird spot under the car, it looks like it is coming directly under the drivers seat but I can see any lines. It's an 02 Santa fe ....
View 8 RepliesI have very good question. My 2001 Santa Fe has 200k miles, I think the car is great. Regular maintenance, and the car drives still drives strong and comfortable.
Here is my problem: The power steering fluid is disappearing. There is no puddle under the car, I got under the car and everything is dry. However about once a week (+/- 200 miles) I have to add power steering fluid. I have cleaned the reservoir twice and confirmed that the top of the reservoir is also dry ( so is not bubbling off the top of the reservoir).
I have put newspapers under the car while parked overnight to see if there is a leak and the news paper is dry in the morning without a stain.
Fluids do not disappear. Could it be leaking while driving (high pressure hose) and its leaking from a location that I cannot see? Where is the "banjo connector" that I have heard referred to ?
I have a 2002 Accent 1.6L and when I turn the wheels all the way too the right or all the way to the left the pulley stops spinning. Could this be that the pump is going bad or something else?
View 2 RepliesMy '02 Hyundai accent's power steering pulley makes noise when the car is turned on all the way. That noise doesn't go away until I shut off the car. It is not the same noise as a belt slipping as I have that problem before and had fixed it by tightening the alternator adjuster bolt.
When I spray a little bit of WD-40 on the P/S pulley bolt(bolt and split washer) the noise goes away. However, it comes back the next day, since I am guessing the WD-40 has been dried away. So, should I replace the pulley to fix this issue or is it something else?
Pic of Bolt (Its yellow and black in the pic) ....
I have a leak coming from the top of my reservoir from the under the cap for some reason. I bought a new cap and it seem to stop for a day and now it leaking out from under the cap again. What is the reason it would be coming out of there. Am I going to have to replace the reservoir??
View 1 Replies