Subaru - Legacy :: 2003 - Replaced Clutch Now Reverse Light Going Out - Clutch Not Smooth?
Apr 7, 2016
I had the car worked on a while back. They replaced the clutch and the viscous coupling in the transmission. ('03 Subaru Legacy manual transmission) Things seemed fine, then I realized my reverse light was acting like it was going out. Fuses are fine. A while later the car decided the clutch didn't need to respond as smoothly. Then: "Nope, you're funny to think you can drive me. I'm not budging." The car started grinding gears. I have to slam it into gear for it to work so I can drive it home and let it sit. The car will go into gear when off, no problem. New fluid has been put in. Bled. Then some sort of SUPER LUBE was put in and it still grinds. What might be happening? I really don't have the fundage in order to buy a new car at this time. But at the same time I hate feeling like I'm chasing a rabbit down a hole..
View 4 Replies
Advertisement
The car has about 142,000 miles. Is the clutch on this car adjustable? My repair files indicate it was "adjusted" a couple times, $40 each time. Now I think I might need a new one: it seems to be slipping, making some noise in 3rd, and in 5th.
View 2 Replies
I replaced the fan clutch and thermostat on my 1999 5.4. Do I need to "burp" the system or anything?
View 1 Replies
I have a 2004 Jetta GLS with 125K miles and standard transmission. Just had the clutch completely replaced. After I picked the car up, I ran some errands, turning the car off and on a few times. Then the ABS/traction control light came on. I tested the brakes, which seem fine, and accelerated on some ice, with no flashing light like usual, so that's a concern. Came home and used the VAG software - no fault codes came up. Went back to mechanic, who said the clutch and this new issue are not related, but he checked my wiring, checked for fault codes, and took it for a test drive. Said he did make the flashing light come on. Turned the warning light off. It came back the next day.
My questions:
- Could this be related to the clutch being replaced?
- Is this something I should worry about, or just live with the light on?
View 2 Replies
My car is hesitating when I shift and accelerate, and revving up the tach after I shift into 5th but the speed doesn't match.Also, in order to start the car I have to press the clutch practically all the way to the floor.
It has 53,000 miles on it. I took it to the dealer, and they said I need the clutch and possibly flywheel replaced.
This seems low mileage to me. I have driven a stick for over 31 years. My previous car was a Honda CRXsi and it was over 110,000 miles before I needed a new clutch.
Is a clutch replacement this early normal for this car? Or is it me? I don't think I ride the clutch.
View 15 Replies
I have a 10 year old 2003 Subaru Forester in "very good" condition....except that the transfer clutch assembly is starting to make noise and the repair shop (at the dealer) says, housing has to be replaced also. The car has 130K miles and has had all its regular maintenance for 10 years. The only major mechanical problem we've had are the head gaskets (which on this year's model were NOT part of the recall). Those were fixed 2 years ago. Some of what I see in the online chatter about transfer clutches suggests that this is a slippery slope and the next thing you know there's the "next thing" that needs to be worked on. We were hoping that the 2014 Forester would get really good mileage (this one got 30 when it was younger) but we hear it will only be 32 mpg so we're inclined to "keep waiting" if this car can be kept happy. Is a transfer clutch repair a big deal?
View 7 Replies
problem is the my 1998 Legacy (142K) overheated this past weekend. It shut off and I had it towed to a "new" mechanic around the corner from my house. He diagnosed the problem as being a faulty thermostat. He replaced the thermostat and returned the vehicle to me. Two days later my wife was driving home and the car had a major overheating incident with resulting serious mechanical failure. I did a little research and within about five minutes found that this problem is quite common for this car and is more commonly related to a head gasket issue. My question is should this mechanic be held responsible in any way for the misdiagnosed problem? If so, what would be the best course of action? The car was otherwise running fine and in fact I recently had the transmission rebuilt.
View 3 Replies
Just got a 98 f150 yesterday and I noticed last night when I went to shift into reverse, with the clutch all the way to the floor as I tried pulling the shifter back, it sounded like the clutch wasn't engaged at all. Shifting from all the other gears works just fine. Ive found that If the truck is off and I start it in reverse it works just fine.
View 3 Replies
Just wondering if it's my car or does Subaru have a light issue going on with the 2011 Legacy's??
I bought my car 1/31/11 (so I'm still under warranty... barely) but here is my history with bulb replacement:
3/22/12 -- 14,251 miles -- driver side headlamp out
6/27/12 -- 17,322 miles -- passenger side headlamp out
6/19/13 -- 27,783 miles -- driver side headlamp out (although was taken in for a passenger side, side marker light)
7/16/13 -- 28,987 miles -- passenger side marker light out (the one that they didn't replace on 6/19/13)
1/22/14 -- 33,759 miles -- driver side head lamp and side marker out
Six bulbs in under 3 years???? Granted these have all be replaced under warranty but the next one won't be despite the fact it's an ongoing issue and that concerns me. I know I'm spoiled because I had a 2002 Honda before the Subaru and in 12 years (mom is now driving it) and 100+k miles I've replaced 1 burnt out bulb.
View 1 Replies
My truck was working fine and I drove it to school one day and I was driving and I noticed the RPM was high and the truck wasn't moving correctly luckily I made it home and parked it now it won't move at all I can shift into gears and I put it in first and reverse and let off the clutch and it doesn't move like the clutch is still disengaged. The Slave Cylinder is pressing against the pressure plate to disengage the clutch and then releasing. I have a single cab 1999 Ford F150 4.2 V6.
View 3 Replies
My 1995 Legacy is slipping in reverse while backing up an incline. On level ground it seems fine. I Changed the fluid, but it's still doing it. Forward gears seem fine. It's an automatic transmission.
View 1 Replies
97 F150 4.9 200xxx 5 Speed .....
I'm having an issue with my truck. It only seems to happen during warm 80+ weather. In the mornings, and during colder weather, the truck runs perfectly.
My problem is; Every time I go to get going and feather the clutch, either in 1st or reverse, my truck bucks wildly.
I changed the plug wires about 500 miles ago, and am about 4000 miles on a rebuilt engine (plugs as well) and new clutch/resurfaced flywheel. The clutch reservoir is full and I haven't noticed any leaks. There have been no codes thrown.
Could it be a possible fuel problem? I think I changed the fuel filter about 7k-10k miles ago.
I was also wondering if the Gotts mod could be causing it. I did the mod during the winter time, and this is my first summer with it on. My air filter is fine.
View 3 Replies
Reverse stopped working after it's been driven for a while. It works when it's cold. I'm actually hoping this was caused by my stupidity (though it may have nothing to do with the problem). A while ago I wanted to change my oil, but opened the auto transmission plug instead. I decided to put new trans. fluid in it. I thought I would add trans fluid until I could see it on the dip stick. After the problem with reverse started I tried to again read dip stick but can't tell where the level is, so I decided to drain trans. fluid to measure it. Owner's Manual calls for 8.8 qts. Drained fluid measured only about 4 qts. I added more. Now it looks like dipstick shows it ~2 inches above the full/hot mark. Questions:
1) Would fluid level affect reverse and not forward (with which there is no problem)?
2) Is method of draining trans. fluid & measuring it a valid way of telling how much is in it, i.e. would all... or most... fluid drain out so the 8.8 qts. in the owner's manual should be added back in?
3) Am I misreading the dipstick? I've tried letting it set for 4 or 5 days, but still fluid seems to smear high on the dipstick.
View 5 Replies
I have a 1995 Subaru legacy wagon, 176K miles. The reverse went out about 10 months ago; all the other gears shift fine and it runs great. Do I have a bad transmission or could it possibly be some kind of switch or solenoid? I have searched the net for hours and keep coming up empty.
View 1 Replies
I just put a new hydraulic system and clutch in my brothers 2002 Saturn sl1. Now we tried to start it yesterday and nothing. Just barely clicked a few times at the starter. I tried jumping it and checked all the connections I could think of that came off while doing the clutch. Nothing. So as I was pulling him home from the shop I had him try to jump it at a slow speed and what do you know fires right up. When we got it home . Turned it off and again nothing it just clicks. So my question is would it be the starter , maybe battery cuz it had a terrible looking ground connection or is something else misaligned on the flywheel. I wouldn't think so since it started and all the gears worked. Its a manual obviously.
View 1 Replies
Put in a brand new Clutch Masters stage 2 kit with flywheel and throwout bearing. Also installed ecs bleeder block. Got everything back together and bled the system. But the pedal is still sticking to the floor with no pedal feel at all.
View 9 Replies
A friend just replaced my clutch in my 07 elantra and now the car wont start! it just cranks over?
View 1 Replies
Santa Fe 2003 petrol manual 2.4
I had a slipping clutch so decided to change it myself.
I replaced the Dual Mass Flywheel the clutch pressure plate and clutch plate.
Re assembled and the car started first time but the clutch would not disengage.
Pressed the clutch peddle down and it went to the floor until the fluid had filled then it went solid.
I pressed it down again and the clutch did not release so pressed harder and 'pop' the master clynder went - but the clutch would not disengage.
Taken the gearbox back off now and the release bearing is in sit it just would not disengage -
View 4 Replies
I recently replaced my clutch and I've noticed that occasionally, while downshifting from 3rd to 2nd, I hear a clunk sound that comes from beneath the back seats. Especially if my throttle bliping is not aggressive enough. What this could be?
View 3 Replies
I just replaced my clutch and have put everything back together, and bled my clutch line, but I have absolutely no pressure still in my pedal. I read that u need to make sure your brake fluid reservoir is filled to the max, but following the clutch line, I dont see it going to the reservoir? I also read that the master cylinder is behind the clutch pedal, does the master cylinder hold any fluid that maybe I lost during the bleeding? I'm at a loss right now.
View 12 Replies
So I just put a new clutch in my 01 Mustang with the baby 3.8l engine and a 5 speed T5OD transmission. The car will shift through all gears fine when turned off, but when I start it in neutral and push the clutch in, it won't shift into any gear. I can start it in first gear though with the clutch pedal in and it moves forward VERY slowly. The trans has enough fluid, and I already pulled up on the pedal to self adjust. Not exactly sure what else could be wrong.
View 19 Replies
