I've read that a scan tool is required to bleed the ABS unit. A brake line has rusted out on the vehicle which I can replace, though not looking forward to it. The ABS unit is disabled by pulling the fuse. Do I still need to have a tech bleed the abs system? Of course I will bleed all four lines at the wheel cylinders and calipers.
View 2 Replies1999 F150 has rusted and leaking steel brake lines. I need to replace all of them but do not know if you have to fabricate them or can you buy the complete kit. I am also confused with the flared end. Have not worked with that type of flare. If they need to be purchased where is the best place to buy them ?
View 9 RepliesI replaced a rear rusted brake line a couple of years ago. It rusted where the line met the bracket. I'd never done this before but bought a flare (flaring?) tool and fixed it.
This week the longer line that runs down the length of the truck started leaking. It looks like the line was once held in place by a small bracket just in front of the rear wheel but it wasn't in that bracket anymore. I guess it rubbed against the metal and water/sand rusted it out.
A local garage said they'd need to drop the fuel tank and estimated that it would be several hours (and hundreds of dollars) to do the job. It looks like I might be able to cut the old one out and then fish the new line up through there and replace it.
Also, what is the diameter of the line? It is a 2004 F350. I can certainly cut it out first and then take a piece of it to the local auto parts place to get the replacement line.
On my '97 F250 the rear brake line going to the rear right wheel has a rusted hole. It measures 50" total. Instead of bending a new metal line. I see they have a "poly armor" line that can be bent by hand( no tools needed). I see Autozone has them.
View 14 RepliesI have a 2000 dually and the brake line that runs the frame rail finally rusted through. It runs on the same side as the fuel tank. Is it easier to leave the old one in and run a new one along side it? I sure hate to think that I'll have to drop the tank for this.
View 7 RepliesMy 2000 SD has a brake line that rusted through. The one that runs along the drivers side frame rail. So I need to get new line to replace it. Since I am nowhere near my truck right now, what is the size of the steel line?
View 6 RepliesFound out my 2007 Hyundai Sonata V6 GLS needs a new brake line put in. The line rusted and all brake fluid leaked out. I am very surprised that after 7 years and only 103,000 km (about 65,000 miles) the car will need a new brake line put in already. All my other cars have been Japanese and have never experienced premature failure and replacement of brake lines.
Granted, I live in Toronto, Ontario, and this year has been a cold start to winter with lots of aggressive salting. It started to get a little bit warmer the last 2 days which probably accelerated the corrosion from the salt.
When I lost the rear brakes due to a rusted line, naturally the ABS light came on. Will it automatically reset when everything is repaired and working or is there something else that needs to be done?
View 2 RepliesI would like to replace the brake line to the rear brakes, and I noticed that the brake line-to-ABS unit fittings have different threads. I already replaced the line to the Left-Rear brake, and it had a fitting with a thread M10-1.0. I tried to replace the line to the Right-Rear brake using a similar fitting M10-1.0, but it did not work. I just damaged the thread on the brake line fitting itself. Then I noticed that the thread on the current Right-Rear fitting is different. what that thread size should be (the fitting to the Right-Rear brake line)?
It is 98 Regal LS 3800 engine.
Just have a quick question. I am replacing some rusted brake lines near the gas tank. I already have the rusted ones cut out. I want to know if this junction box is really needed. If not it would sure take out alot of bending the lines. It looks like the line only come down the frame and bolt into the block and then straight out to the rear wheels.
[IMG][/IMG]...
03 F250 7.3. I busted a brake line last week somehow, Got it replaced and fixed up, Bled that line and everything was somewhat good.
Now, when i hit the brakes hard, I have pressure. If I let off even a little, My pedal will start to sink till i apply more pressure. I am gonna fully bleed my brakes when I'm home to see if this could solve the problem.
What's the best way to changed a EGV valve on a 1996 Ranger? The metal line coming from the exhaust manifold to the EGV valve, is seriously rusted on both ends. It looks like if I don't heat the metal line, the line will just round out, what's the best way to tackle this job.
View 6 RepliesI have a 1999 Chevy Suburban and for some reason I've having this problem the my one brake on the passenger side won't light up when you press the brake but the other side will. And also when I apply the turning signal on the passenger side it blinks really fast and you can see the front signal flashing fast but the back does not flash at all. So for some reason the brake and signal lights don't work at all on the back passenger side. But the running lights do go...
View 14 RepliesI am replacing the rear steel brake lines and I have a bit of a mystery...when the lines come off the wheels, I see them going over the pineapple and it LOOKS like it's just coming down the other side into the other wheel. That should be impossible, right? How would it go about getting brake fluid into the system?
I can't see on top of the pineapple, so I don't exactly know whats going on up there. I don't see any hydraulic hose coming from the top of the pineapple. I'm currently clueless as to how the rear brake lines fit together.
I have a 1999 Subaru Impreza Wagon that I have owned for about 2.5 years, and I love it. I travel for work and I use rental cars alot. I have noticed in the past year that my brakes feel softer than most cars I drive, but I figure.. they are new cars, and my car is pretty old.
In the past 2-3 months I have notices a pulsing in my brakes...it sounds/feels kinda like the ABS, but I was thinking it would be worth getting my brakes inspected soon.
Then this past week, I totally blew a brake line when I was driving.
The car has about 140,000 miles on it and the mechanic says a brake line alone may not be related to the pulsing sounds...because brake lines usually go because of rust....
So...thoughts on things I should be looking at? What could the pulsing be a symptom of?
if one brake line blew, and it is rust, is the other one not far behind? (this was a new england car up until 2 years ago)
I have heard that the front brakes are separate, and if the rear brakes have a leak and the line is empty, the fronts should still work. Is this likely to be true? If I drive the truck will I be able to stop with the fronts alone (assuming they will still work?)
I plan to drop the truck off late tonight when there is likely to be no traffic, but thought I would ask.
Working on putting this project back together and cant find my notes when I pulled it apart last year. Any schematic or picture of their brake lines from the master cylinder to the rabs or front brakes? Better yet, which port on the master cylinder goes to what axle?
View 9 RepliesFirst, I am fortunate that I was only going 25 mph when some turned in front of me causing me to slam on the brakes. The pedal went to the floor, but did slow the truck enough to miss the jerk. Had I been on the highway, it would have been very bad.
Anyway, what I found is still hard for me to believe for two reasons. It find it hard to believe it failed, but more important that I am getting the last national inventory of 2 of the 3 lines in this picture (according to my Ford dealer).
The three lines are almost directly under the front end of the master cylinder between the block and frame. These are as I found them. The larger one goes to the rear feeding both rear brakes while the two smaller run to the front brakes. The spring looking part below is just a plastic protector. The line which failed goes to the front left.
I think anyone with a 2005 SuperDuty which uses the same or similar parts should take a very close look at the flex sections. The parts I have ordered are: 6C3Z-2B523-BA, 6C3Z-2263-BA, and 6C3Z-2264-BA (rear, right, and left).
How long a manufacture is required to maintain inventory? I thought 7 years, but someone suggested 17. I'm at 8 years, but I would have expected more than 1 each of the fronts to be available. Do they changed parts on the '06 or '07?
My 350 spent 2 winters in the Chicago area and has been resting in Florida since 2006. No work was done in this area, but the closest work was the main fuel pump (frame mounted) replaced 2 years ago, but that is almost 2 feet to the rear.
2003 Ford excursion 7.3. Above the drivers side front tire, the hard inner plastic made contact with the hard line above the frame.. Cut the line. I can't tell if this line is 1 piece towards the reservoir since its hidden from my quick inspection. Looking for a schematic on replacing this line?
This happened after my wife took the truck back to the sugar bush.. She must have been hitting jumps or something
2002 F250 diesel ... I found these two plastic pieces yesterday on the floor near the 4X4 shifter. I noticed the other day when i step on the brake the rear view camera in the head unit comes on, so i am thinking they are either a part of the brake switch on the pedal assembly, or something to do with the shift tube.
View 2 RepliesHad the rear passeneger side brake line burst today in rush hour traffic ..wasn't much fun. Is it a easy to do it yourself deal ...it is a 2003 f250 v10 triton .
View 1 Replies