Dodge - Grandcaravan :: AC Turned On - Temp Needles Do Not Move Up Or Down Stay Steady
Aug 12, 2014
Replaced the ac compressor/filter dryer/exp block on 04 dodge grand caravan. pulled vac for 45 min, let sit for 1hr. No movement of needles no leaks. charged system to 2.69, start van turn on ac compress clutch engaged but will not cycle off stays engaged. Air temp from vents 60 to 65 deg, low side 55 psi high side 250 psi at 85 deg air temp needles do not move up or down stay steady. high side hose from compress very hot ( burned hand on it ) low side hose to compress warm/cool.
View 5 Replies
Advertisement
I am considering buying a 1999 Dodge Grand Caravan with a reported transmission problem. Mileage is around 120k, and the price MIGHT be reasonable even if a trans rebuild would be necessary. I have not seen the vehicle yet, so I'm not yet committed to anything.
Seller claims the car shifts just fine going forward but will not move in reverse. Is this immediately clear that rebuild is going to be necessary? Are there less invasive repairs possible such as valves or controls or other parts which might solve this problem?
I suppose a Caravan transmission at 120,000miles is probably nearing the end of its lifetime, at least that was true of older ones. But like I said, the price is low enough that the cost of a rebuild might be justifiable if all else about the vehicle looks good. I want to have a better sense of the prospects before I invest time in going to look at this...it's about 50 miles away. I have a local transmission shop that I trust and which has reasonable prices
View 17 Replies
Our 1997 Grand Caravan with 170K loses more air conditioning every year. So, I assume I have a slow leak. Is recharging something I can do myself with the new type cans offered by auto parts stores? Also, I think the radiator fan no longer comes on, I never hear it and the engine temp will go up when driving slowly around town.
View 1 Replies
1996 Dodge Grand Caravan, 3.3 L engine. When the outside temp is a good range (50 degrees F & above) there is no problem starting. But when it gets below 40 deg. F and really chilly outside temp, I still have strong battery power, but when I switch on the ignition, I don't hear the normal fuel pump activation swirl sound and does not crank - simply silent click. Then I can wait when the outside temp improves and cranks up no problem.
View 6 Replies
I drive a 2005 Chrysler Town and Country with just over 47,000 miles. I noticed that during the last few days, when I start the car, the needles on the fuel, speedometer and temperature gauges go all the way up and then back down. After they finish moving, I then see the engine lights go on and off. Normally, when I start the car, just the engine lights go on and off. The movement of the needles on the gauges is new. This is now happening about every other time I start the car.
The car itself seems to be starting and running just fine. I haven’t noticed any drop off or change in performance. What could be causing this oddity? Is this a warning that something worse is about to happen?
View 10 Replies
I have a 2005 mkiv GLI and my gas gauge, temp gauge, and information display stopped working when the car is running. They work when the car is on auxiliary but not while it's running. The lights all work on the cluster all the time but the needles don't move as soon as the car turns on.
View 3 Replies
2004 F150 Supercrew
44400 miles
So I turned on my truck today and the needles acted as if they were possesed. The went under the "starting points" and vibrated there for about 5 seconds or so... Very strange. I also have been getting sluggish power from the truck. Mainly between 2000 and 3000 rpms.. Sound like a diesel at times.
View 14 Replies
98 accord v6, when we first got it about a year ago the temp gauge was a little erratic. Sometimes it would stay all the way down (cold) after driving for awhile. You can take your finger and thump the plastic and it would jump up to normal. At first it was only temp, but now all gauges including gas level are not working. Odometer still works right but the speedo goes to about 45 and stays there. Thumping still makes the needles bounce around.
View 10 Replies
02 6.8 4x4 excursion. When I start the truck cold, the trans temp gauge immediately moves to "running" temp. Not really sure how this happens, I'd figure that if the xducer was trash it would ride all the way high or all the way low. What's happening here? I'd sure like a functional gauge...
View 6 Replies
I have had my 07 now for a few months. The other day during a trip, I noticed my TPMS light began to blink, and then stayed constantly on. I checked my pressures at the end of the day and they were all right where they should be, including the spare. When I start the car, the TPMS light will blink for some time, and then it will go steady and stay illuminated.
Took the car to a tire shop and they hooked the tpms scan tool up to the car and told me I had a bad sensor. I did some reading online today and it seems like a lot of people say the sensors that come from the factory for these cars only last for about 5 years until the internal battery dies.
For what it costs to get one sensor replaced, knowing that the car is 5 years old and the other 3 sensors are prone to fail, I see some people are making little PVC canisters and putting all 4 sensors in the canister and pressurizing it to make the light go away. But my sensors are broke, and if I bought new ones I do not have a tool to program them.
Is there anything that can be unplugged, or a wire that can be cut or grounded to make this stupid, pointless light go away or am I pretty much at the mercy of the tire shop/dealer to replace the sensor and make the light go away?
View 14 Replies
I have a 2004 Grand Caravan 3.8 engine. For the last 2 months the oil light has been coming on when car is first started. If I stop engine and start again the light will be off. I don't think its actual oil pressure because the car runs fine with light on or off. I'm thinking a bad pressure sensor?
View 17 Replies
Sometimes when I start my 2006 Dodge Grand Caravan, 3.3 liter engine, the oil light comes on and stays on, even if I rev engine up. Engine sounds normal, does not sound like oil pressure is low. If I turn engine off and the immediately back on, light goes out and stays out. I replaced the oil pressure sending unit - didn't work. I hooked up a gauge - engine has 60 psi oil pressure at idle - plenty! I'm guessing an electrical problem in the circuit.
View 4 Replies
I have a 2005 Grand Caravan, this winter has been a cold one. The GC has always started without problem but after I back out of my parking spot, it sits outside, I put it into Drive and it will not move and after I give it a little gas it would still not move. None of the gears seem to work, but if I wait a little bit and the Van warms a little more it will go into gear and all is good. This does not happen all the time and when it does go into gear and I drive I do not have anymore problems until the next time it will "act up" on me again. Is this a problem or is it a cold problem and not a transmission problem?
View 7 Replies
My 2000 Dodge Grand caravan loses its gauges every so often. engine light comes on as well as ABS...
View 2 Replies
I got a great deal on this van, and I love it, with one exception. On hot days (73 degrees and hotter) the van will not start if it has been parked in the sun; until the temperature returns down to around 61 degrees (usually overnight, but I have waited it out in the parking lot at work a few times).
When this happens, the lights and radio work fine; the starter motor will not engage. No click, no chugga-chugga vroom-vroom. Sad Curto.
Note: October through about May in North Carolina, this car is fine.
I have replaced the steering column (after replacing the clock spring); I have replaced the Power Distribution Center.
When the problem first surfaced two years ago, I had a mechanic install a wire directly from the starter motor relay to the solenoid. That was an expensive lesson. I'm not sure what the lesson is, so it was REALLY expensive.
So, I thought maybe the Auto Shutdown Relay. Nope... pull that out, and the starter still turns, so that is not my problem. Now I am starting to thing Powertrain Control Module, or something else that could have a temperature-sensitive component.
View 10 Replies
I have a 2004 Dodge Grand Caravan with 120,000 miles. Starting at about 45mph the car has a really bad shimmy when accelerating. The shimmy fades starting at about 55 mph. There is no shimmy when not accelerating. Gently applying the breaks has no effect on the shimmy. I've put on new tires, Change the steering rack and struts and the engine and tranny mounts. what could be causing this?
View 2 Replies
I have a '09 Dodge caravan. The ABS, ESP, TCS, and Brake lights are on. As we drive along the brakes apply, probably on only wheel. After we stop, we can drive on for a short way and it happens again. A mechanic told us that the steering sensor was telling the computer that the steering wheel was turned all the way to the left. I wonder if I pulled the fuse for the ABS pump and ABS valve if it would be safe to drive, at least until we can get it to the dealer for repair. I am cheap and like to get by as cheaply as I can/. I am not fond of ABS, or TCS any way?
View 19 Replies
I have a 1993 Grand Caravan 3.3L V6. When I leave the van set for a couple a of days (or even overnight) and then start it, I have no oil pressure for a minute or so. After the engine has been running for about a minute or so the oil pressure finally comes up but not to normal. Once the engine has warmed up the oil pressure returns to what could be considered "normal". After the cold start, no oil pressure problem, the engine and the oil pressure is fine for the rest of the day. Let it even set overnight though and I have a repeat no oil pressure with start up.
I am thinking that there is a problem with the pick up tube not sealing properly and allowing the oil to bleed down while the engine is off for an extended period of time. So, in effect, I have to basically prime the oil pump at each start up. I haven't noticed any leaks of engine oil anywhere, so I am thinking that this is an internal problem. Is there a check valve or O-Ring associated with the pick up tube or oil pump that may cause this problem? Is it a fairly easy problem to correct? On this engine the oil pump is located in the front of the engine block behind the timing chain cover. (As best as I could determine from the Haynes Manual).
View 13 Replies
Lifters are rattling. They have been replaced and are still rattling.
View 17 Replies
I have a 1998 Grand Caravan 3.8L engine with 157K on it. A month ago changed the EGR valve and replaced the transmission oil. Two days ago, went for shopping, parked the van. Came back and did not start (no crank, nothing). Called AAA, checked for battery, which was good. Radio, wiper, lights work. Had to tow to the shop. The mechanic checked for all possible problems. Said everything (Fuse, battery, starter motor, alternator) is good. He is clueless. Told him to check the ignition switch (may be worn out). He says it doesn't seem so.
View 19 Replies
The 96 Caravan I bought a year ago came equipped with an aftermarket dent in the oil pan. It's a bent up generally flat, not all at one point, but there's no leak and no other apparent problem, though of course it does reduce the oil capacity. When I had some overdue warranty work done at a dealer, the service writer told me the dent is exactly where the the oil pickup is, which mostly sounded like the dealer looking for some extra work. I decided I'd replace the pan myself when I had enough miles on the car to see if it was worth the effort.
The pan has a lower sump area that measures roughly 5" x 7" and that entire portion is pushed up somewhat evenly. I'd estimate the deepest part of the deformation is almost an inch, so less than 35 cubic inches lost capacity. 35 cu in = .606 quart.
I can buy a new oil pan w/ gasket at Rock Auto for a shade over fifty bucks to add to an order I otherwise need to place with them. A used pan at the local junkyard would cost ten or twenty bucks plus my labor plus the gasket, which I judge as not enough cheaper to be worth my time and inconvenience (they want me to capture the used oil and take it with me). So it's either buy the new oil pan, or fix something else. Or pull the pan, bend it back to shape, and replace the gasket? It appears to me that the pan gasket may be seeping, though not enough to drip, so it's probably due for a gasket anyway.
Should I care about this, or learn to love the dent?
View 16 Replies
