My car is taking a long time shifting from reverse to drive in the morning. Do you know what may be causing it and how to fix it. It's a 1995 automatic ford explorer.
View 3 RepliesThis problem started at the beginning of this winter. So I started to idle for 2 mins and the car was shifting without an issue.
However, now it is completely stuck and wont shift to 3rd gear even if I drive for 15 mins at 60mph.
Have a 2003 Saturn Vue with a variable transmission (rebuilt). It will only go in reverse even when in drive, or natural.
View 5 RepliesI just got myself a 1993 ford explorer and the damn thing won't drive forward but it will drive in reverse. What could be the problem?? I've already drained the Transmission Fluid out & refilled it. My friend told me it is most likely the Neutral Safety Switch but I have no clue where it is located. I will be honest I have absolutely no clue about vehicles.
View 1 RepliesWhen I started my car and put it in reverse, it didn't move. It felt like my front, right wheel was in a divet or was being blocked somehow (intuitively it seemed like if I accelerated enough, it would eventually move, but since there was nothing physically stopping it - that I could see - I didn't want to break something by doing that). I tried putting it in drive and neutral and the same issue was still there. I put the car up on a jack and checked one wheel at a time - I could move each wheel completely around in both directions.
I could move the steering wheel all the way to the right and to the left. I tried turning off the 4-wheel drive and that didn't do anything. At this point I'm concerned it could be the transmission or the drive shaft, but I'm not sure what to look for in order to know if I need to get it towed to a shop (hoping I can avoid this) or if there's a simple test I can do, or a way to "reset" something if it may be locked. I haven't had anything happen to the car that would have been of concern.
The truck will go into reverse, but will not go into drive or any of the other gears. When shifted into one of those gears, it just idles as though in neutral. This started as I was driving down the highway at approximate 70mph. The speedometer jumped up then fell to zero as the car slowed to a stop. There was no noise except the sound of rapid fuel intake and then it went to idling. I have been told it may be a speed sensor, but I was wondering if there was anyway to confirm that before I have the truck towed down to a mechanic and find out its more than I want to pay to fix it.
View 1 Replies2003 Explorer tranny. 4.0 V6, 213km (133 miles)... Biggest concern is 4-5 upshift shudder, no rpm rise, just a shudder and slow shift. Slight shudder on 3-4 too, I think. Some online reading points to torque converter failure.
Other symptoms: sometimes slams into gear when shifting out of park, other times it feels like there is no fluid in converter when first put into gear, especially after sitting a day or 2. (my truck does the same thing, but that's after sitting 2-3 weeks at a time)...
I had a clutch, slave cylinder, and master cylinder replaced about 20,000 miles ago. Everything seemed to be working fine until I drove across the Rockies. The transmission was extremely difficult to shift, and the vehicle would actually roll forward when cranking the engine at fuel stops (temps were minus twenties). Once I got out of the mountains on both ends of the trip (where it was warmer), the clutch worked normally. The local Ford dealer found lots of air in the hydraulic clutch system, bled it, and it worked fine for several months.
The clutch is doing the same thing currently, but not all the time. Some days it's fine, other days it's difficult to shift although double clutching seems to work. It gets particularly hard to shift after a long drive (e.g., interstate driving for a couple of hours). I took it back in this morning to see if the dealer could figure out what is going on, they're saying it's likely a bad slave cylinder. I've heard the 1995 Explorer clutches are a bear to properly bleed, and can't work but think there may still be some air in the system.
I have a 1970 f250 with a factory 390 (vin verified) and a C6, I believe the transmission was rebuilt but have no way to verify. It works fine while cold and mildly warm. Once heat soaked it is very slow to shift (going from neutral to reverse can take almost 30 sec) and leaks profusely from the front. I can not tell exactly where the leak is. Could this be a case of just having too much fluid or is there a more serious concern? The dipstick does read high but level ground in my area is hard to come by so the accuracy can be questioned. If it does have to much fluid, do I just drain the pan, re-install and let it run till hot and replace fluid as needed or should I drain and replace with 3 qrts prior to starting?
View 7 RepliesFinished my flush, but now it won't shift to reverse unless i shift all the way to drive first. I thought it might be the hard shifting lever(i think something is up with the linkage), so i shifted to neutral, then reverse, but no success. It's still about 1/4-1/2" overfilled, I jsut ran to the hardware store and it's consistently still not shifting to reverse unless I take it all the way to drive first.
Really hoping I didn't break something in the process... I did do the shifting through the gears while it was flushing out the old coolant, could the valve be stuck due to that?
I Have a 1996 Ford Explorer XLT my problem is my truck will shift into reverse but nothing else. Whats wrong with my truck and how do I fix it...
View 3 RepliesMy brother in law has a 93 explorer which developed a serious transmission leak and had to be towed home. We suspected a blown front seal, which we replaced. We also replaced the transmission filter and pan gasket. When we started it up, it seemed like it was stuck in gear and wanted to move forward no matter what gear it was set to. Even wanted to go in park and neutral. We topped off the fluid, and finally got park to work, but all other gears including reverse want to go forward and it seems as though it is not shifting at all. Could we have forgotten a connection of some sort, of could something internal been damaged when the fluid was lost?
View 6 RepliesI recently bought my grandfather's old F-150, its a 1983 model with the 351w and the 7200VV carb. I replaced the distributor cap & rotor, plugs, wires, and fluids. The truck idles just fine in park/neutral, but when I shift it into reverse or drive, it stalls out. There is a valve of some kind attached to the carburetor, and it opens and closes rapidly as the truck dies (in time with its sputtering) so I think it may be the cause of the problem. I have not been able to find much info on that carburetor, but I think that valve is a fuel temperature system that meters the amount of fuel going to the carb depending on is temp. Can I replace that part without having to replace the whole carburetor?
View 10 RepliesGot a call from my little sister about two weeks ago that her Ford Explorer would not drive forward. Checked it out and put it into second to get it home.Last weekend me and my dad changed the filter and fluid and then drove it for a bit. It sounded a little better but still would go into drive or reverse. We shifted into second which we knew worked and then back into reverse immediately and now reverse worked, although sluggish. The same was true for drive. A few days later dad changed a solenoid and now it will go into drive and go up to 15mph, but will not shift from first to overdrive first. And still no reverse right away. She is able to get to school with second gear and pop into drive when she gets up to 40-45mph. If she has to backup from start, first she has to put it into second and then back to reverse. Something in overdrive doesn't seem to be doing its job right.
View 3 RepliesI have 2001 ford explorer sport.. it idles very low in drive and reverse and then shuts off.. What has been replaced:
1. Torque converter
2. All new plugs n wires
3. Map or mass sensor
4. Iac valve
5. O2 sensors
6. Fuel filter
7. Air filter
8. Throttle valve/sensor
It does not run bad only when u come to a red or stop light.. Had the vacuum tested and no vacuum leaks.. also no check engine light has come on and no codes have popped up when tested..
I was pulling into my driveway. I put the car in park, but when i went to get out of the car, it started to roll forward. When I finally got it stopped, I tried to shift it, and it wouldn't shift to any spot. Then it became stuck in between Park and Reverse. I can't move the gear shift.
View 1 RepliesIt is a 2003 xlt 4.6 auto. sometimes, but not too often, when you shift from park to reverse nothing happens, no go backward.... even if you mash the go pedal. if you shift to drive then back to reverse it works fine. Not predictable enough to show it in failed mode to the mechanic. Is this a common simple fix? would this issue throw a code? (No blinking or idiot lights on dash when it does this) is there something I can tell the tranny guys to look at since it is on my dime? Somthing like a shift solenoid or something...
View 2 RepliesMy daughter's 2002 Saturn S-series coupe has a manual transmission. Lately it has been jumping out of 2nd gear, and occassionally 4th and reverse. What is the most likely cause?
View 2 RepliesI got myself a 1997 explorer Australian model when I got it (here's the problem) if you put it in drive it will not engage but if put in first will drive normal then shift into second all good now u have push O.D then shift into drive all good (unless u slow down to almost a stop) ? New problem is, it has gone and lost reverse, put it in reverse and it engages with a small clank (normal) but just slips with any revs. I have read posts here talking about upper and lower valve body gaskets and transgo shiftkit which I have ordered but do there maybe more parts needed? Cause it's going to cost me lot just to put transmission fluid back in.
View 4 Repliesi am having problems shifting. it wont shift into reverse all the way and when its in drive it has a hard time shifting from first to second gear and wont shift into third.
View 1 RepliesI bought a 2010 V8 Explorer on Monday and aside from the apparent "known issue" with the hard 2-1 shift (which I'm trying to get it to "unlearn" by driving differently), it's a really nice truck.
When I shift into reverse it says "Park Aid On/Off" in the display, and sure enough, it beeps when I get close to something. That said, there aren't the normal "dots" in the bumper that I normally associate with backup sensors.
Everything works just fine with it, I just am a guy who likes to know how things work and I don't see anything on the outside that would indicate it's a parking sensor.