Jeep - Liberty :: 2003 - CEL Has Been On And Engine Knocks
Apr 25, 2015
2003 Jeep Liberty Sport, 156 K miles, Check engine light has been on for months now. First occurrence was when driving, and car started to knock as though I was shooting 50 cal machine guns. Stopped vehicle, shut off, and upon restart, engine ran smooth. Now, almost every time after engine has been running a while, and I am going on a down slope, the check engine light starts to blink, and engine starts to miss. Took to my mechanic, and so far, I have been told and have replaced, Fuel pump, Spark plugs, coils, and wires, cam sensor. Latest and most recent with promise that this has to be it, I replaced engine computer.
View 16 Replies
Advertisement
My '03 Jeep Liberty developed a quite audible hole in the exhaust system overnight (sound is coming from engine compartment) and at the same time has begun missing. The missing occurs most often in the low end of gears - once through the gears (in 4th or 5th) and at highway speeds it smooths out again. My question is are these two problems related?
View 1 Replies
I got a new-to-me Jeep Liberty 2005 in February. The check engine light came on after a few weeks. Our mechanic replaced the catalytic converter twice. After the second replacement it went out after we drove for a while, but after the second one it never went out. We are now using high-test gas (to prevent carbon buildup?), but that hasn't worked either. I need to pass the emission test soon.
View 6 Replies
I drive a 2003 Jeep Liberty Sport, with the 3.7 liter V6. It has roughly 97,000 miles on it.
In the year or so that I've owned it, the jeep's check engine light has come on several times. Every time I've had it checked, it's the same issue - a small evap leak, code P0442. Typically, they'll reset the computer, and I'll drive it for two or three months and eventually, the code will come up again.
Oftentimes, I'm told it could be caused by a loose gas cap. I'm aware of that and I try to make sure it's nice and tight every time I fill up. I've also looked at it, and there are no visible cracks or holes in the cap itself. But, the problem still occurs.
So, What this could be besides a loose gas cap, could cause an intermittent small evap leak?
View 2 Replies
I have a 2003 Jeep Liberty, which is making a rhythmic clunk (Click and Clack's not oft referred to cousin) on every wheel rotation, when veering to the left. Going straight there is no noise, right, no noise, and oversteering left also makes the noise go away. Braking also makes the noise go away. Mechanic said they could not determine why it was doing this. It's not real loud, but noticeable at any speed, particularly prevalent at about 30 mph. Clunk noise happens once per tire rotation. I've seen similar threads here, but nothing "exactly" like this. Don't know how to duplicate the weight/momentum/centrifugal forces with the car stationary.
View 2 Replies
I have a 2003 Jeep Liberty V6 automatic 4x4- the car is getting stuck in neutral and won't change into gear. It starts up just fine and runs okay for about a mile before I notice a terrible hissing sound when I press the gas pedal just before it acts up and locks in neutral- dangerous on the highway as I have to pull over, shut it off and then restart which then resets but soon comes the hissing sound and again it locks in neutral... I tried adding Lucas transmission fix but this did nothing.
I purchased this car (2003 Jeep Liberty Lmtd. V6) the check engine light has been on for 4 years now- none of the mechanics I've brought it to have been able to figure out why. ( hoses changed and nothing) I have not had a smoke test done. I started having start-up issues. The radio and all the lights come on but the car won't start (rule out battery), eventually after a few tries, it starts up.
I've also noticed, when in reverse, sometimes it stalls, a few times it has shut off on me while trying to park in reverse gear, sometimes when driving it kicks as if it is having trouble shifting into gear (it's automatic)- and finally, the hissing and revving sound when pressing the gas pedal, it shifts into neutral and gets stuck there....
View 5 Replies
I have a 2003 Jeep liberty sport with 175k on it. it has a misfire cylinder 2 code. I replaced the plugs and coil packs on all 6 cylinders, noid light test on wires, compression check in all cylinders, everything works so far. I still have a check engine light for the misfire. I don't know if maybe the injector is bad for that cylinder, looks like it was recently replaced as with the other 6, or i have a leak of oil or air or coolant into that side either from the head gasket or intake gasket. the valve cover gaskets have been replaced recently as well.
View 6 Replies
About 2000 miles ago, I had the transmission on my liberty serviced. I had the pan dropped, the fluid drained / refilled, and the filter replaced. The work was done by a jeep dealer. The jeep ran fine with no rough shifting or error codes - in fact, I drove it 500 miles this weekend without incident. This morning, I backed out of my garage and found a big puddle of red fluid on the ground.
I warmed the vehicle up, and checked the transmission fluid level. It appeared to be low, so I added some (about 1/3 a quart). I then looked underneath the jeep and observed red fluid leaking from the transmission pan area. I ran my finger around the bottom of the pan and ended up with more fluid on my hand.
The fluid is clean - no discoloration or burnt odor. What might my problem be? Could it be an improperly sealed trans. pan? Something else?
The jeep is an '03 and the transmission is original to the vehicle. Bought it with 83K and have done fluid / filter changes at 90K, 120K, and 153K. Currently at 155K.
View 5 Replies
I have a 2006 Jeep Liberty 2.8 Diesel. It has about 57000 miles on it and when I took it to be inspected, a Code PO 299 came up. The dealer has done quite a bit of work to it and cannot find a way to get this light to stay off. When something is done, it goes off until it is driven, then it comes on again. So far the jeep runs great, but it's hard to pass inspection unless the light goes out.
View 7 Replies
My engine seems to misfire when I first start out and then runs smoothly. The first mechanic got a random misfire from the diagnostic and replaced all the cylinder coils which worked for about a week. The second mechanic ran a diagnostic which said random misfire and he said it was a loose spark plug. This worked for 4 days then it started misfiring again. There's no violent shaking or backfiring. I don't know much about cars but it seems odd that it doesn't keep misfiring. It's a 2006 jeep Liberty with 87,000 miles...
View 9 Replies
I was driving home from a backpacking trip when I noticed a knocking coming from my engine. It got worse as I drove up a large hill and suddenly became very loud, and I lost the ability to accelerate, power steering and brakes.
I managed to pull off the road and checked all my fluids, everything was good. No smoke from the engine and it was not over heating. I was unable to start the car, it wouldn't even make a noise, just dead.
Check engine light is broken and remains on. No other warning lights came on while I was driving.
View 12 Replies
I have a 2005 jeep liberty 3.7L with 60,000 miles on it. The engine light when on 2 weeks ago and gave a p300 code. the dealership replaced coil and plugs, I believe. Then would start rough when cold, the engine light would blink for about 10 seconds then remain on. the car runs just fine except when cold....first minute of starting it. they checked for head gasket problem, and cant seem to find the problem. They told me that this could just be something that happens. I don't believe that. I have no loss of power, no hesitation. Runs fine 99% of the time
View 19 Replies
i stared my jeep today and when i was driving it wont go pass 45m and doesnt wanna accelerated...
View 5 Replies
I have Jeep Liberty 2002 with 100300 miles. I having starter problem and the starter was replaced with a new one. Still I am having the same problem, the car can only re-start 30 minutes or more after I shut it off. The mechanic stated that he does not know what it is causing the problem.
View 11 Replies
I have a 04 3.7L V6 Jeep Liberty with about 114K miles on it. It started happening recently that when I turn the key nothing happens. I have to put my foot on the brake, shift thru the gears, back to Park, take my foot off the brake, and then the car will start. Not quite sure where to start...
View 3 Replies
My 2004 Liberty just started this a couple weeks ago. When sitting still, the AC blows hot air. It cools down nicely when you start moving. This makes traffic lights and people who don't go when the light turns green VERY annoying. While waiting, I can hear the compressor coming on and off. Thinking perhaps the radiator fan wasn't coming on, I looked at the radiator fan fuse, 40 amps, and it looks fine. I even checked it with an ohm meter. With the car sitting still, engine running and AC on, I don't think the radiator fan is going. Maybe one of these two relays?
Important details (or not)5 speed transmission125,000 miles"What color is the car?" Blue.Two wheel drive. (alas, it's a Jeep in style only)
View 7 Replies
My radiator fan is not turning on in my 2002 Jeep Liberty. The belts look fine and it turns by hand. My radiator overheated last summer but since has been fixed now my fan doesn't work, but hasn't overheated. No parts of the the radiator or fan were removed. We fixed a part in the water pump this past sunday and when we had the engine running for about 15 minutes, the fan did not turn on or even act like it was going to try. What the issue could be?
View 9 Replies
I have a 2006 Jeep Liberty Sport. The key is stuck in the ignition. It will still start, but when I go to turn, it's like the key doesn't want to release those last few steps. Which is as safety issue because my car is sitting ready to be stolen. When I called the dealer they wanted to charge me, just to figure out what is going on with it plus labor and parts to fix it.
This is a known issue with the '06 Jeeps and Chrysler is not wanting to do anything about it. At this point, I just need the key out of the ignition. The dealer said they would have to pull the ignition system apart to get the key out which would cause the car not run at all. We tried tapping the key to get it to release and it hasn't done it yet. It did this once before and we where able to jiggle the key and it released but it is not working now.
Again it is a 2006 Jeep Liberty v6 3.7 Liter Engine it is now sitting at about 78000 miles happened the first time at about 50-55000 miles.
View 3 Replies
Following on the recent storm (Sandy) I got to my car and realized that water was leaking in from somewhere near the dashboard. Subsequently, it seems as if the electrical panel has been affected. Initially, whenever I pressed the brakes the back wiper of my Jeep Liberty (2003) would come on. That has subsequently stopped. However, now when I turn the car off the radio continues to play and I have to turn it off manually, the clock no longer goes off and the horn no long sounds when I turn on the alarm.
I took it in they hooked it up and said they couldn't see anything wrong with it. They had never seen the problem before, that they called the dealer and they had never heard of anything like that before. I have subsequently used sealant on where I think the leak originates but don't think I was particularly successful. So the problems are how do I deal with the leak and what might possibly be causing the radio, alarm problem. I should also say that I was out of town for a few days right after the problem and when I came back the car would not start so apparently there is some kind of "parasitic drain" on the car but again no-one seems to know what, where, or why.
View 1 Replies
i have a 2002 jeep liberty.the cv shaft is popping.do i have to replace anything besides shaft.to fix jeep.
View 4 Replies
I stop to put gas in the car, put the hose in and set the "latch" so I don't have to hold the hose (which I have done for years) What has started to happen is the hose does not shut off and gas spills out. I have tried holding the hose with the latch in place, and then readjusting the height/level that the hose is at,, it still spills over... since this is something new, what is going on !
View 3 Replies
