Mazda - Mazda6 :: 2006 - Horrendous Racket Like Sound And Jerk When Accelerate Into 4th Gear


Jul 2, 2014

I have a 2006 Mazda 6 that ive owned for a year now. It has this random problem tho.... when accelerating into 4th gear it makes a horrendous racket like the bottom is falling out of the car or something and sorta jerks. it has been doing this a long time. other than that it drives fine! i have no mechanical knowledge about cars so im totally clueless! this seems to happen when accelerating on an incline.

View 3 Replies

Advertisement

Mazda - Mazda6 :: 2006 - Bad Noise And Jerk In 4th Gear

we have an 2006 Mazada 6 automatic transmission with the option of manually shifting gears. we have had it a year and the only maintenance is work on the air conditioner, oil changes, and new tires. when accelerating on an incline or sometimes during/after a curve as it shifts into 4th gear it makes a terrible noise and the whole car jerks. the best way I know to describe it is it feels as if the bottom of the car is about to fall out! when we first purchased it, it done this a couple times and basically quit doing it for a few months.

It seems to be getting worse though. we have never had a check engine light. we sent a can of "sea foam" through the gas tank and this seemed to work. a local mechanic examined it and test drove it but couldn’t find anything wrong with it. (of course it didn’t act like this when he drove it!) I called mazda dealership and they cant tell us anything without us bringing it in and charging us no telling how much just to look at it. no one seems to be able to figure this out….

View 4 Replies

Mazda - Mazda6 :: Clutch Started Sticking Right Where It Would Engage Into Gear

I have a 2006 Mazda 6 with 104k on it. The clutch started sticking a couple weeks ago right where it would engage into gear, and I'd have to use my foot to pop it back up. It only happened here and there until finally, it stuck to the floor and became very difficult, if not impossible, to get out of gear. So everywhere I looked, it seemed that the slave cylinder was the culprit. I got a new one at AutoZone, replaced it yesterday, and the car ran great last night and this morning.

Then, this afternoon, in one 10 mile trip, it went back to the original problem. Stuck with every gear change, then stuck to the floor after I pushed it in and darn near wouldn't come out of gear. What in the world could be the problem?

View 14 Replies

Mazda - Mazda6 :: 2007 - Loud Sound That Comes From Under The Hood

I have a 2007 Mazda 6 with 133000 miles on it. Recently it has started making a very loud sound that comes from under the hood. The sounds is comparable to the sound a semi truck makes if it is idling. The noise is not constant, usually happens when I put the car in park or if I'm driving at low speed (under 20mph). The sound lasts around one minute.

View 2 Replies

Mazda - Mazda6 :: 2007 - Shutter Before Turbo Boost / Difficulty In 1st And 2nd Gear?

I just spent $658.22 on a EGR flow valve on my 2007 mazdaspeed 6 with 55,000 miles on it. This after two years of complaining about a shutter right before turbo boosts. Now I am having difficulty getting the car into 1st gear and 2nd gear. Took it to the dealer "can't duplicate". As I am driving away from the dealer I grind 2nd. Took it back to the dealer, went down the street with the service manager and grinded 2nd gear again. The service manager says "I'm shifting too slow". I am really concerned all Mazda dealers are waiting for warranty to go bad before they repair anything. Powertrain warranty is up at 60k something tells me I am going to pay for it. Why I am having difficulty in 1st and 2nd gear?

View 1 Replies

Mazda - Mazda6 :: 2003 - Rattling Sound In Engine ONLY When Car Is In Drive Or Reverse

I have a 2003 Mazda 6 and heard a rattling sound in the engine ONLY when the car is in drive or reverse, never when in Park. My mechanic said it is the clutch in the alternator that is coming apart and so the Alternator - tensioner - belt all needs to be replaced for a total of almost $800. Does this seem reasonable?

View 5 Replies

Mazda - Mazda6 :: 2006 - P0302 Random Misfire - CEL Comes On

Mazda6. I have a check engine light for a random misfire on cylinder 2. I have changed the spark plugs, the injector, and even the cylinder 2 coil, but still have that random misfire. The funny thing is that it would run great within short (about 30 miles) one way trips. Lately, I have gotten a new symptom: It has started to hesitate and can feel a loss of power but only once the car has been driven for about ten minutes non stop. Can't figure this out.

View 12 Replies

Stalling - Mazda - Mazda6 :: 2006 - Run Rough And Idle At 1000 RPM?

I have a 2005 Mazda 6. When it is cold - I start the vehicle & begin to drive. When I slow down and the RPMS get around 1000 - the car begins to run really rough & try to stall. If I put my foot on the gas - I can usually prevent it from stalling. The problem disappears once the car gets warm. The dealership recalibrated the PCM based on a Mazda Alert. However, it has not corrected the issue. Looking for thoughts on what could be causing this?

View 5 Replies

Sonata NF (2006-10) :: Clunk Sound When Accelerate Normally As Going From 2nd To 3rd Gear

I have a 2006 Sonata LX with 91,000 ,miles and today it starting making a clunk sound when I would accelerate normally as it was going from 2nd to 3rd gear. My question is this: I have 91,000 miles on it and have owned since new in 2005 (8 years). Does it sound like a transmission problem and would a transmission problem be covered under the 10 year, 100,000 miles warranty?

View 4 Replies

Volvo :: 2006 - Quick Jerk When Punch The Gas To Accelerate Quickly

My 2006 Volvo S60 turbo has about 116K miles and noticed a couple times when I punch the gas to accelerate quickly (like to pass someone on the interstate) that it will make this quick jerky thing (as though I ran over some rumble strips). I normally drive like a grandma so this has only happened a couple times. Today I was on the interstate and decided to test this out and sure enough it would quickly bump-bump-bump before the gas/acceleration kicked in. It never stalled, but now I am paranoid.

Also, it occasionally "feels" like it takes the car longer than normal to start. There is no pattern to this. It will happen first thing in the morning, but I have noticed it more often when I stop to drop my son off and get back in the car. I will crank the key and the RPM dial will shoot up twice really quickly and then be normal.

Maybe you should also know that when I first got the car, I filled it up with gas and started driving and it died. We checked the fuses and the fuel pump fuse had burned out so we changed it and all was right again.

I bought this as a high mileage car (60K) in 2007 and have not done much to it since (air filter, oil, tires, brakes). Yes, that means I have not gotten my transmission fluid changed or any recommended dealer maintenance.

View 14 Replies

Mazda - 626 :: Strong Rumble Stripe Like Sound And Vibration At About 60 MPH When Accelerate

I have 1997 Mazda 626 I4 5 speed manual transmission with 140k on it.

All of a sudden I am getting a horrible reoccurring vibration and noise that sounds like I'm driving on a rumble stripe at about 60MPH coming from the front end when accelerating.

It speeds up as I accelerate.If I push down my clutch or let off the gas it goes away immediately. While turning right it will go away immediately until I straiten it back out.It happens in any gear at any speed in any weather although it seems more likely to happen when everything is cold.It isn't always there and there seems to be no rhyme or reason as to when it happens or clears up.

View 16 Replies

Mazda - Mazda6 :: Misfiring On Cylinder 3 / CEL Flashing

My '04 v6 wagon 100K will misfire in really damp conditions. Last fall after going through a massive puddle and today after sitting for a couple of days of warm damp foggy & rainy New England spring weather. OBDII scanner is reporting cylinder 3 as the one misfiring in the fall, today there were a ton of codes (that I didn't note).

So I made it about 2 miles from the house and had to turn back. No power, check light flashing. I had to put it in manual and keep the revs highish (3-4K). When I got home the exhaust manifold was glowing yellow, assuming one or more cylinders were passing fuel out to the exhaust and it was being burnt off in the manifold.

My question: could I have damaged any gaskets back there? This could be my imagination but I think I'm hearing a new noise that I'd normally attribute to an exhaust leak downstream of the muffler, very subtle - like a gentle light but rapid thud. I only hear this noise with my ear to in the front driver's wheel well. There's no ticking noise I normally attribute to leaks near the manifold. My imagination or is it easy to damage something in the circumstances I describe?

View 11 Replies

Mazda - Mazda6 :: 2003 Will Turn Over But Not Start

My son's mazda 6 will turn over but not start. the things I have done:

1. replace crank sensor
2. replace cam shaft sensors
3. it has spark
4. fuel pump works
5. sprayed starting fluid in still will not start.

What else should I check? Security system?

View 2 Replies

Mazda - Mazda6 :: 2003 - Car Suddenly Stops While Driving

I have a 2003 Mazda 6, 5-speed manual transmission. I was driving on the highway today (going about 65mph), and all of a sudden, my car kind of "jolted" (like it stalled out). When I tried pushing the gas pedal, the car wouldn't accelerate. When this happened, the check engine light (and some other lights) went on, too. I pulled over to the side, turned the car off, and turned it back on. It seemed to start fine and gas/acceleration was working. Fortunately, I was able to get home, but it started doing it more frequently up until I got to my apartment. Each time, I had to turn the car off and restart it.

Oddly enough, when the car does this and I pull over to the side, the engine is still on. However, even though the engine is on and the car is idling, I noticed the RPMs were sort of jumping between 0 and 1000, and the engine was sputtering (like it was sputtering with the RPMs jumping, the only way I can describe this sputtering is like a heart beat). The only thing that seems to work is to turn the car off and turn it back on, which will then allow the gas pedal to work, only to have it happen again a few minutes later. The gas pedal doesn't get stuck or anything, it's just pushing it doesn't seem to accelerate the car.

I've already had the engine replaced on this car last year (at 80K) and the clutch a few months ago, too.

View 5 Replies

Mazda - Mazda6 :: Front End Vibration At Certain Speed And When Turning Right

2009 mazda6, I feel some vibration feels like wheel is out of balance coming from the front left wheel, it's most noticable at 30mph and again at 60mph. It's more noticable when i'm turning right, e.g. shiting to the right lane.

Already replaced four tires, balanced the tires and replaced front struts and rear shocks.. and it's still there!!

when shifting to the right lane, the vibration feels like da-da-da-da-da.. like I'm driving over some washboard road.

What could this be, is this CV-joint? can I ask dealer to check out CV-joint see if it's ok?

View 3 Replies

Mazda - Mazda6 :: 2003 - Chronic Ignition Coil Cause?

Can a problem elsewhere in the system cause ignition coils to go bad? I have an '03 Mazda 6s, 147k miles, owned it since new (Dec '02). 3 1/2 ~ 4 years ago, over a period of 6 months I had to replace 4 of the 6 coils. A month ago, one of the replaced coils went bad so I had all three rear bank coils replaced (cheaper to do all three at once rather than one at at a time since half the engine needs to be disassembled to get at them). This week, I started to get the initial symptom of a coil going bad on me: Occasional stuttering in the engine.

This issue always starts when it's wet outside. The first few times it started when going through a car wash, this last time was right after Super Storm Sandy dumped a lot of rain (I am not in one of the flooded areas, NH just got a lot of rain).

View 9 Replies

Mazda - Mazda6 :: 2003 - Some Hesitancy To Shift Into 1st When Cold

I have a 2003 Mazda6, 108K miles. Had the ATF changed last December at the dealer. Prior to this, there was some hesitancy to shift into 1st when cold. Last several months, it has gotten worse. Engine revs (as much as I allow it, which ain't much) and then goes into first. Dealer thought they had overfilled the ATF, and reflushed and refilled. Said they couldn't find any other problems. There is no CEL. Problem was better for a short while after fluid change, but now back to long hesitation. Car goes into Reverse fine when cold. Once the car is warm, I don't notice the hesitancy to shift to first. How to diagnose?

View 1 Replies

Mazda - Mazda6 :: 2003 - Control Arm Bushings Cracked

MILEAGE: 65,000

Last time I was in, the shop replaced my sway bar links, which had already been diagnosed and the repair scheduled. Then, after replacing the sway bar links, the mechanic told me that the control arm bushings were cracked. They already put new struts on the front, as well. So I asked him what else was going to go wrong with my suspension. He said nothing else should need work. He also said that the car was safe to drive for a couple months but I definitely needed to get it fixed.

QUESTIONS:

Is it normal for a car with 65,000 miles to have cracked bushings? I realize that the car is 11 years old; I just wondered how much a car's mileage plays into cracking the bushings and, if so, after how many miles should one expect before cracking occurs.

Does it sound like they're trying to soak me? Why tell me one thing at a time? Perhaps more revenue from the labor side of things?

Assuming the bushings truly need to be replaced, does the community here think there is anything else that should be checked and taken care of at the same time? It is both costly and annoying to have to take the car back numerous times.

View 4 Replies

Mazda - Clutches - Mazda6 :: Clutch Disk Wore Out, Car Won't Move

I have a 2005 Mazda6 4 cyl manual transmission, purchased this past holidays. Last week the clutch disk totally wore out and the car was not moving at all... AT 68000 miles only. I am a new manual transmission driver and I think I might have been part of the problem. My mechanic, who is a family friend, has replaced already the clutch kit and he found out that the clutch disc was not only worn out but actually damaged, shattered on a side. So I got scolded by him and my father as they suggested that I damaged it by doing improper shifting. They suggested that I went from 4th or 3rd gear to 1st thus damaging the clutch disc for the car to totally stop moving.

However that's very unlikely in my opinion. I don't know if Mazda included some sort of safety feature in the transmission, but the car never let me go in 1st gear if it was already in motion, the shifter would lock if I attempted (found that out when driving in stop-and-go heavy traffic). I thought my problem was due to my foot frequently flirting with the clutch pedal in order to keep my driving and shifting smooth. In fact a few friends of mine who drove manuals in the past complimented me on my driving becoming so smooth in a short time. I also think that I bought the car with the clutch kit carrying some sort of damage on it, since in the first weeks of ownership, my practice period, I would often smell a burning odor when I was not doing things smoothly. Once I got better I never smelt the odor again until a few days before the clutch gave out.

View 7 Replies

Mazda - Mazda6 :: Transmission Shifts Really Hard After Driving For Some Time

I have a 2003 Mazda 6. Almost every day, after starting it and driving maybe .10 of a mile, it seems as my car shifts, it shifts really hard, like a thump. I am thinking of having the Transmission serviced. Is this worth it? About what should the cost be? What do they do, just drain the fluid and add new?

View 2 Replies

Mazda - Mazda6 :: Feels Like Shifting When Going Uphill At Low Or High Speeds

I've got a mazda 6 v6 3.7 from the year 2010 with approx. 69000 miles on the clock. I noticed when going uphill at low or high speeds that the car seems to feel like it is shifting but it actually isn't. For example when I drive on the highway about 70 going up a hill it feels like it shifts every few seconds even on manual mode in 6th gear.

When I hit the gas it shifts back and I don't feel it anymore. At lower speeds it feels like it is doing a whole lot of shifting at low/medium acceleration. Again if I hit the gas and accelerate faster the car just goes normally up its gears. I think this is the torque converter doing this, but I am not sure whether it is normal?

View 6 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved