Mazda - Mx-5 :: 1999 - Runs Rough Like Hitting On 3 Cylinder Now Won't Start?
Jan 31, 2014
I bought a '99 MX-5 in the fall with 100000 miles on it. Most of the time it runs fine. But about every two weeks when I go to start it it will run real rough like its only hitting on three cylinders then will eventually smooth out after anywhere from 5 seconds to 2 minutes. But today it wouldn't start at all. Finally started just fine after trying for 15 min. My mechanic changed the EGR valve but it hasn't worked. The check engine lite stays on all the time but when it starts rough the lite will flash.
View 3 Replies
Advertisement
This problem has been getting worse over the last 2 years. When the car starts it idles fine at about 1000 RPM. As soon as it warms up, it starts to idle rough, between 500 and 750 RPM. It almost quits running. As soon as you give the car some gas it runs just fine. About 3 weeks ago I got a "Engine Lean" check engine light error. I reset the system and have not gotten the error again. Since then I have: changed the MAF cleaned the EGR (made sure it closes completely and ohm out the coils in the actuator) changed the O2 meter on the exhaust manifold cleaned out the throttle body Ohmed out the air idle controller. What I should check next. I was planning to check the fuel pressure in case it is a fuel system problem. It is a 1999 ....
View 5 Replies
Our 07 Mazda5 (80k) once in a while will start and run very roughly, and pressing the gas to the floor only gets it to 3,000 rpms.It has diminished power for climbing hills when this occurs. Everytime this happens if we shut the car off and let it sit (between 10 minutes - a couple hours) it starts and runs like a top. We have added drygas 2 of the times, but the last time it happened was on the same tank of gas that we added the drygas to. Check engine light comes on, but will go off after a day or so.
View 5 Replies
My 99 250, 7.3 is having some strange issues as of lately. When I start it in the morning, when the engine has fully cooled down, it starts right up, then it throws the "wait to start light" runs real rough and just shuts off. Run the glow plugs a few times, start it up and it will do the same thing for maximum 30 minutes, then all the sudden I start it and it runs fine. I've replaced the fuel pump, cleaned the fuel bowl, new fuel filter, I just don't know where my problem could be. It doesn't make sense. But once I get it running and it warms up, runs fine all day. Go to bed, wake up, has problems again.
View 14 Replies
I have a 2005 Hyundai Sonata 4cyl. and have a misfire problem with the 1st cylinder. I've had it pressure checked and there isn't a problem with the cylinder, such as a ring or warping problem. I've replaced the wires, both boots, both ignition coils and the plugs twice. I was told I need to replace the ignition coil again but I wonder if there is something that is making the coil go bad. I've also replace the throttle position sensor and both O2 sensors. I had the front catalytic converter replaced because it was bogging down and very slow. It still runs rough and the check engine light is on. I was told also that I need to replace the engine speed sensor. I bought the car in Oct. of 2004 and only has 68000 miles on it.
View 2 Replies
I am working with a friend on his 99 Ranger with a 4.0 . When first started it will idle rough and hesitate for the first 300 feet or so, and then clear up and run smooth the rest of the day. If he lets it set for 6 or more hours it will repeat the problem. He has taken it to a local Ford dealer and they have replaced spark plugs, plug wires, coil pack, cleaned the throttle body, checked the air idle motor and passage.
He has had it to the dealer 3 times and their latest plan is to pull the heads @ a cost of 1500.00 to start. Since it runs well, no coolant in oil or oil in coolant nor loss of either fluid, I couldn't figure why they want to pull the heads.
To date it has not thrown a code, I ran it on a New Generation Star tester and cannot find a code. The truck runs great after the first intial start up and does not give any signs of cutting out or lack of power. My guess is it is losing fuel pressure overnight and is taking a while to reprime. Original fuel pump and 160K miles. Will do a fuel pressure test this weekend.
View 1 Replies
I have a 1999 Ford Escort SE wagon with 112k miles on it. Last week when leaving work my car started very rough. This was unusual so I killed and restarted the car about three times before letting it run it's course (~30 seconds), after which the car ran fine. About a week later on my way to work the car seemed to 'sputter' (for lack of a better word) when I pushed down on the petal looking for some power on two separate occasions. On each side of the sputters the car seemed to respond fine, but when it did sputter there was a severe lack of power. I got to and from work just fine, but while letting the car idle in the parking spot of my apartment for a minute before shutting off the engine the check engine light finally came on. The following morning the car again started rough (as if it were misfiring/running on 3 of 4 cylinders) and this time it took a good minute before smoothing out. However, after the car smoothed out I experienced no issues on the way to work, no sputtering, no loss of power, nothing. Doing some initial online research I feel that the problem may be one (or more) of the following:
-Fuel pump
-Vacuum lines
-O2 Sensor
-Spark plugs (they are original)
-Fuel Filter (it is actually past due for replacement)
I plan on getting this checked out ASAP, but that still may be 2ish weeks away with my schedule. Some similar reports say that I may be having a 'lean mixture' issue (not getting enough fuel), but I haven't had the time to check the code. My question is, how "safe" is it to continue driving my car with the current situation? Is it at a super high risk of failure/random stalling during rush hour? Will it cause any damage to the engine if there is a cylinder misfire upon start up? I was also wondering if the car would be reasonably reliable to drive on a ~400 mile road trip on an upcoming weekend, but I am making plans as if it is not.
Additional Details:-Tried charging the fuel lines (car to 'ON' then 'OFF' position 3-4 times), had no effect on the morning start-up-Commute to/from work is about 20 miles
View 13 Replies
I just bought this 99 f250 7.3 Powerstroke last week.. drove it all week fine, I car pool with a family member to work and asked his girlfriend to plug my truck in for me, well she didn't and it had stalled on the way home one morning but started up after cranking a few times i thought nothing of it. Drove it a little bit that day and it was fine, while I let it idle in my drive way as I prepared to go work it started running really rough then died. It took a long time to start again..now it's happening all the time. I changed the fuel filter and someones telling me there's air in the lines..
View 5 Replies
I bought a 2005 Camry LE 2.4 4 cylinder. It was rather loud while driving, but especially while accelerating. It had error code P0420 from the beginning. It had a completely broken torque strut which I eventually replaced. Afterward since it toned down the kicking from the engine, I was able to notice that I could feel and hear the engine kicking like a cylinder misfiring. The computer gave me error code P0353 (Ignition Coil C Primary/Secondary Circuit Malfunction) consistently, and only a couple of times gave me error code P0500 (Vehicle Speed Sensor Malfunction) which went away.
I swapped the ignition coil and spark plugs around but the error code would persist on the same cylinder. The spark plugs didn't look particularly worn but I'm not experienced on what bad plugs look like. The codes persisted still, but later on P0353 went away, and the obvious kicking stopped but it still ran with a lack of power and hesitating on acceleration along with a strong smell of fuel in the exhaust. I measured the resistance of each fuel injector and all measured the same. I removed and flushed each of them with cleaner, but same situation.
What do you think? I don't get the bad cylinder code anymore but something is clearly wrong. Bad fuel injector? Bad wiring harness? Bad compression or head gasket (maybe from the movement of the engine while the torque strut was bad)? Hopefully not the computer... And could the loud noise be related to this problem or is that probably just a cracked exhaust from when the torque strut was allowing engine movement?
View 5 Replies
1994 Maxima SE 5 speed manual with 178k runs great when engine is cold, then a cylinder starts missing. Symptom is worse in low gears. Then, miles and miles without a miss. Replaced rear ignition coil and it seemed to fix the problem... for about 20 miles, then it started missing again. And stops missing… for miles.
View 2 Replies
So I did a cylinder contribution test and a buzz test today. It buzzed evenly on all cylinders. Then when I did the cylinder contribution test I got these codes,
P0269 cylinder 4 contribution balance
P0284 cylinder 8 contribution balance
It has been running a little rough lately but not smoking. Seems to be chattering more than it was too. I did the FRx, HPx, CVDs and banjo bolt mods about 500 miles ago and it was a lot quieter and ran better. Just recently started running rough and a little louder. Could these injectors be bad? I did new injector O-rings about 800 miles ago. I ran the test with the engine cold and with it warmed up and got the codes both times. It seems to have a little bit of throttle flutter when holding it about half throttle while driving.
As far as I know the injectors haven't been replaced and they have 186K miles on them.
2001 F-350 Lariat Dually Supercab 6-spd manual 7.3 Powerstroke Turbo Diesel 186,000 miles....
View 9 Replies
I have a 1992 mazda b2600i, recently lost all brakes. Changed the master cylinder, but now I have a major problem!! I have no power to start it. I have head lights, dome lights, horn, buzzer when key is in start position. Nothing when try to start, no click, no trying to start nothing!! I have changed the main relay, all fuses. broke down and contacted a mechanic and he is telling me that I have to have the 2 computers replaced... there is one under the kick panel on the pass side and one under the driver seat!!
View 7 Replies
1995 G20 5.7L... This van runs great when first started and continues to run fine after it's warmed up and will do so until it’s turned off and restarted. When first started vacuum at idle is steady at 21” and 10” at 55mph cruising speed. I can continue driving for an hour or so and it will continue to run fine. It's only when I shut it down and restart after 20 minutes or so that I have a rough running condition. After parking for 10 to 20 minutes and restarting idle is still steady at 21” vacuum but the van hesitates on acceleration and runs rough at cruise with a 5” vacuum. If I continue to drive I get low vacuum trouble codes for the MAP and Oxygen sensors. I’ve replaced the oxygen sensor and performed a diagnostic on the MAP sensor which checks out ok. I’ve checked for vacuum leaks – none found. I've replaced the spark plugs, cap and rotor. What to look at next?
View 8 Replies
I'm working on my sons 1985 Celica GT 22RE. He was having problems with it running rough.
I've isolated it down to the number 1 cylinder being starved on warm starts. If you cold start it the problem does not occur but if you let it sit warm for 15 minutes it will fire up but nothing from number one cylinder. Lots of spark but no firing. So I'm going to tear down the EFI and move the injector to see if the problem follows it. Will probably see if I'm getting any voltage to the injector while rough before tearing down.
I can't find anything about an injector not working once warm so I'm thinking it may be an ECU problem.
View 5 Replies
I'm having a weird issue with my 1998 Ford ZX2. The car is very hard to start when cold and it runs extremely rough, but only through my first acceleration under load. In other words, I can rev the engine a few times while in neutral, and it will run very rough, and once I start driving, it runs really rough through my first acceleration, but then it smooths out and runs fine from then on until I stop it and let it call off for 30 minutes or more. If I restart it within 30 minutes or so, everything is fine, but any longer that that and the problem reappears.
View 3 Replies
96 civic 120K miles, stock, automatic.
In March I was running low on fuel, maybe 1 gallon left in the tank. It took a few cranks and on the last try i gave it a little gas and it started, albeit very rocky for about 1 minute of driving, filled up immediately and 2 freeway miles later, no real issues. I live in LA so very low ambient temperature is not a problem.
April through May, starting was a little rocky, it was inconsistently rocky too, sometimes there was no problem. Usually it's weak, stuttering, sometimes just cranking but I seem to get it to start. I stopped giving the pedal gas because I read that's bad (I own a vintage bike, so it's news to me). I don't drive that far and figured I'd try some Seafoam and some freeway miles would clean out any debris. Worked for that tank a bit for the next tank before the problem came back.
Still getting the rough starts, but now when I give the car gas as I pull out sometimes it doesn't accelerate for 15-30 seconds, maybe 25 yards then it drive like normal. No dying at all but getting worse with starting up.
I've tried turning the key (not turning the engine over) 5 times and cranking on the 6th and it seems to work. I thought maybe it's the fuel pump or fuel filter but read it could be an ignition coil/ spark plug/ spark plug wire issue. Two different ball games.
My MPG is not really droppingI had a new fuel filter put in in February as routine maintenance (thing was on so tight had to bring it to a shop so no rookie mistakes there). Timing belt &water pump replaced 6,000 miles ago
View 3 Replies
My 2001 V70 24T runs smooth when cold as it warms up it runs rough with delayed acceleration reaction ....
View 1 Replies
About 2 weeks ago my 1997 Buick Park Ave (115,000 miles) began running bad during a heavy rain storm. It was running fine. Then all of a sudden at a stop light the motor hesitated and wanted to stall. I nursed the gas peddle and limped home and turned the car off. The car hesitated and sputtered all the way home as if I was running out of gas.The next day the car would not start. It turned over but would not start. I tried starting the car for three days. My mechanic friend later diagnosed the car and stated the computer was not functioning correctly. He replaced the computer. The new computer seemed to correct the problem.
The car ran great for the next 2 weeks. Yesterday, it was raining hard while I drove the car about 150 miles without any problem. Then suddenly again the motor started running badly. Again, the motor wanted to stall and hesitate as if I was running out of gas. I limped home again. This morning I tried to start the car without any luck. In addition to installing a new computer, In the last 2 months I have changed all the fuel injectors and installed new spark plugs.I have also changed the fuel pump and repaired the fuel tank. My mechanic say the cam sensor and crank sensor are operating correctly. There is spark coming from the coil packs and to the spark plugs. I do not want to randomly change parts.
View 3 Replies
I got 2000 tdi with 270000km on it and have a few issues with it and am looking for some information before i start doing some work to it.
First problem excessive blue smoke on start up also runs ruff tell it warms up.
Second the is a screeching noise on start up some times. happens most of the time when the car is cold.
Third sounds like something is dragging or rattling but i have checked and there is i can see.
Fourth when the clutch is in and the brake is on the car runs ruff at idle. i think it has something to do with vacuum used for the brake booster but not sure.
View 1 Replies
I have a 2000 E350 boxtruck with a 5.4 auto. The motor is a new rebuilt with about 4000 mile, coils were replaced with motor, injectors were rebuilt with motor.Today (500 miles from home) the truck died. I was going up a slight hill on an interstate. It will still start, but runs very rough and when I put it in gear and step on the gas it dies.
So I had it towed to a garage. While pushing it into the garage I noticed my gas cap was missing. I know it was on 45 min earlier because I got gas. Did I forget to put in back on? probably.. But I wondering if the missing gas cap could cause the truck to run bad,vary bad?
View 14 Replies
My '03 6.0 is hard to start and runs rough when cold. Not just cold outside temps, but engine not up to temp. Starts and runs like a champ once it's up to temp. It was doing this when I got it, but it's getting worse.
From what I've read the common culprits are:
1 - failed solder joints on FICM power supply board
2 - bad power supply side of the FICM
3 - updated flash needed for FICM
4 - injector stiction
5 - leaky O-rings at high pressure oil rail to injectors
I have read up on how to run the voltage test on the FICM with a multimeter.
Seems like I would have to go to a dealer to have the software version for the FICM checked.
I am 100% competent to do the tests and/or repairs myself, but since I recently moved in with my fiance in a condo and my tools are in storage, I will have to do it at a friend's house. That being the case, I want to know what all of the common things are that I may need to check for so I am prepared. So, I wanted to see if there were any other common causes of this issue.
I plan to test the FICM voltage and give FICMRepair.com some business if that's the problem. And if that's not the problem (or maybe even if it is) I will get the injector seal kits and replace all of the injector seals as well as disassembling and cleaning the spool valves in the solenoids. I will also change oil and fuel filters with Motorcraft parts and Rotella synthetic oil while I'm in there.
View 14 Replies
