94 Saab will not start in the mornings , it cranks but wont fire , runs fine later in day with no problems at all . Than next morning a repeat performance of not starting.
View 10 RepliesI brought my 2000 9-5 Saab to Jiffy Lube on July 13th. On July 18th, it wouldn't start. It would turn over and everything, but it would just sit there and do the, "ruh ruh ruh ruh ruh ruh." I waited half an hour, and tried it again and to my surprise, it started. I drove it home without issue. The next morning, it did the same thing, but this time, it didn't start. Had it towed to the Saab guy, he says there's no compression in two of the cylinders and that it's going to be $1000 to fix the thing. I called someone for a second opinion, and he asked if I had run out of oil because no compression usually means an issue with the oil or something. Could Jiffy Lube have done something to cause an issue, and if so, is there anything that I can do about it?
View 16 RepliesMy 2006 Azara has had a no start problem since about a year after we bough it new. The condition is intermittent and is not dependent on outside temperature, humidity or other conditions, It happens when the engine is cold or hot. Sometimes the problem goes away for a week or so then it comes back. It happens with either key.
The engine cranks over but does not start. Usually resolve it by sitting for 10 - 15 seconds then trying again. Sometimes have to do this two or three times before it fires. All other electrical items work ok and the battery has no problem powering accessories. I've had it into the dealer however because it is difficult to replicate, they have a hard time repairing the problem. The first time they neutralized the immobilizer and re-programmed it. The second time, I got a check engine light and they replaced the immobilizer. But the problem continues.
i just rebuilt the motor in my 2002 ford ranger 3.0 and it wont start it cranks over but back fires and bucks alot. took the plugs out and it gets spark and fuel. when it sparks it sparks like multiple times.
View 3 RepliesAlright I thought changing a fuel filter was fool proof but I changed the fuel filter in my 2001 escape v6. awd and now for some reason it wont start right up like it used too before the filter change. It cranks for a few seconds then fires up and runs perfectly fine it sits for a few hours same issue where as before the filter change it fired up fine every time, what did I do wrong. 2001 ford escape...
View 1 RepliesSo it often just cranks for 15 seconds before it fires. I put the fuel pressure guage on it and you turn the key on but don't engage the starter it goes to 30 psi then back to 0 in a 2 second time frame. It then stays at zero. when you engage the starter pressure slowly goes up and it starts running while running its a consistent 60 psi.
I presume its the fuel regulator but why does it not go up to 60 psi and why does it just stop with the KOEO? Is it reasonable to just replace the regulator? or should I be replacing the fuel pump to at the same time? I will be doing this from under the truck since there is a lot of hard mounted equipment in the bed.
Ok so i bought a 1994 celica GT from a police auction the other week and it wouldn't start so we went ahead and put a new fuel pump in it then we put new spark plugs in it. When removing the spark plugs i saw there was oil on them. My friend suggest we do a motor swap cause he thinks its a blown head gasket. Could this be an easy fix or should i go through with the swap?
View 5 RepliesI got a caprice 94 l99 it was driving perfect. i was on my way home then it started to put put then the engine cut. gave it like 3 mins it started drove 1 block started to put then the engine cut. now doesnt start at all just cranks the gas gauge says it has 1/4 tank of gas.
View 5 Replies1994 Geo Tracker 1.6L 16V engine won't start, but cranks. I have spark, compression is good, fuel (good fuel), new spark plugs, the crankshaft and camshaft are timed, the distributor is timed, there are no error codes but the ECU is fine.
I've put in new spark plugs and wires, new fuel injectors, new timing belt, new air filter. All sensors are hooked up and working. It cranks, but doesn't start. It keeps burning fuel, I can hear it and feel it in the engine, but it won't start and run.
One thing which I've noticed is weird is the crankshaft is very difficult to turn when it hits certain points. I try to turn it and it will go about a third or a turn pretty easily, but then it gets stuck and I have to turn the key to get it past that point. Then I try to turn it by hand again and it has the same problem in a different spot. It hasn't started in a month at this point, I'm planning on taking the distributor out and realigning it tomorrow, but I'm running out of things to test.
My 1994 850 turbo will crank but will not start. it started when the car was having trouble accelerating past 40 mph and felt like it was kicking back then it died on the freeway and now will not start. i ran the error codes and got these back, from A2 452, 455, 543, 544, 545, 552, 555 and from A7 122. I'm not sure what to do?
View 4 RepliesMy mother's 2002 Camry with about 60K on it has been starting hard lately. No check engine light has come on. I did a full tune up hoping the problem would be solved but no luck. The car cranks a lot before it fires. First thing in the morning it cranks more than it should, starts, and then she gets a little smoke out of it. The rest of the day it cranks a lot before firing. I'm assuming that it is a fuel system issue because if she turns the key to the run position and waits a few seconds, the car starts up normally. Sounds to me like the fuel is draining back. What controls the fuel from draining back to the tank in a 2002 model with a 4cyl, the fuel pressure regulator, fuel pump, or something else?
View 5 RepliesMy kid is using my 94 Ranger with 215,000 miles. It quit while he was on his way to work. Engine cranks but won't start.
Fuel pressure at rail was 12 psi (Key on eng. off). I replaced fuel pump. Pressure at rail up to 20 psi. Still cranks, no start.
I replaced fuel filter. Pressure at rail up to 30 psi. Still cranks, no start.
Replaced distributor cap/rotor and plugs. I have spark at plugs.
Chiltons from 1994 doesn't list a rail fuel pressure. I see new fuel pressure regulators are set at 41 psi. I pulled mine and hooked air to it. It (FPR) cracks at 37 psi. I have lots of flow returning to tank, so I assume the fuel system is working correctly. I've never replaced the timing chain/sprockets. Distributor rotor spins during engine cranking. When I rotate the crank pulley to 0 Top Dead Center the rotor is pointing to #1 on the distributor, so I don't think the timing chain has skipped a tooth on the sprocket??????
1994 Caprice Classic (350 cid LT1)... Engine cranks very slowly, almost doesn't start, sometimes starter disengages/re-engages. 1year ago mechanic checked batty, alternator and starter, all ok. I had starter replaced as it seemed the most likely cause. Eventually got better but now is worse again. Also notice a lot of movement on the dash voltmeter needle, sometimes high, sometimes low, turn signal moves the needle. Ive spent hundreds of dollars on troubleshooting and the new starter. What could be causing this?
View 4 RepliesI've been having this occasional starting issue with my truck. I turn the key and the engine acts like it's going to fire up, so I let go of the key and it doesn't start. Then I try to restart it and either it cranks and fires a few times before it starts, or it fires right up and the starter grinds because I couldn't let go of the key fast enough.
I've had this problem a few times before, but lately it seems to be happening more often. It works normally 98% of the time. Maybe I'm just not letting the engine crank long enough to get it to run before letting go of the key.
Also, the spark plugs were just changed 10k miles ago and when the truck is running it runs great.
My eXcursion is showing the typical signs of a failing fuel pump. It cranks and fires on a few cylinders, then quits. I released the schrader valve on the fuel rail but very little pressure is released. From these indications, and after checking for a blown fuse, it appears the fuel pump is going. I say going because it did start after this happened, but would you trust it?
I ordered a new fuel pump, it's due in tomorrow. I remember seeing instructions on how to drop the tank but can't locate them with the search function. I'm also concerned with how to remove the pump from inside the tank. I know you have to spin off the big plastic ring, how do you get the pump off the bottom of the tank?
I was hoping to have this resolved, but it seems how I have it parked affects the cold starting of this thing. Had an issue quite a while back as listed in another thread where the truck cranks and fires then immediately dies when cold. Takes at least three times to fire. Once fired it has no problems and will start easily unless it sits for almost a days time...on flat ground.
I replaced some injectors recently since they were bad and I had the truck parked facing downhill slightly when I did that. Since the repairs, the truck would start fine while parked there. Brought my trailer home and have the truck in the street on the flat ground and once again the 3 crank starts begin.
I have attached three Excel spreadsheets of my data from today. All three are the same data log just split up for size and elimination of dead time on the original spreadsheet.
So, I am guessing I have a HPOP problem, which is probably why I was getting intermittent contribution codes when the truck is up to temp. The truck fires totally fine when the oil is hot and up to temp so hot starts are no issue. Could the pump be "stuck" or just not working right when it has sat?
I have the notorious PO171 and PO174 codes on my 2003 5.4L that come back whenever I erase them. I cannot figure out the problem. Whenever I start the truck it cranks for 3-4 seconds before it finally fires, then rpm's are very low, then they finally pick up. I have noticed a loss in power as well. I have completed a full tune-up (spark plugs, coils, boots, filters, etc.)
I have checked the vacuum and PCV lines numerous times, I have yet to find a leak. MAF appears clean. I am running a K&N CAI setup. O2 sensors a good, replaced the gas cap. The only other problem I can see is a bad PCV valve? I hope it isn't a manifold gasket. The truck has been very well maintained and still looks brand-new throughout at 250,000 miles.
My 2011 f-350 6.2l cold starts hard, it cranks through 2 cycles sometimes before it fires, then it might stall. Sometimes it stalls if I put it into drive or reverse before its warmed up. It has also misfired on one or several cylinders during startup. It has also misfired while driving. It has never stalled when driving. I have replaced the canister purge valve, I have done a full tune up with all factory plugs. All with no change to how it starts. My next step is a Pcv valve, I have one coming from ford today.
View 5 RepliesEvery time it rains and I forget and leave the truck outside instead of inside the garage, it will not start. It is a 2001 Dodge Dakota pickup truck. It tries to start but will not fire. I have to sit around and wait for a few dry days and full sun - which is hard to find around here other than August and September. I have had it towed to several different mechanics for review. They have all done the same thing - can't find anything wrong so they leave it sit around the lot for two or three weeks until the sun shines then charge me a hundred bucks or so for their diagnostic time and a jump start. Every once in a while out of shear frustration, I have it towed to a new mechanic or one of the previous ones but still get the same results. Does fine in the winter with snow, but it has even done it on occasion when going through a car wash - which I know longer do as I am too old to be pushing a pickup out of a car wash.
View 3 RepliesSeems like sometimes on cold start ups the car hesitates before it fires up. Thoughts?
Start up IS-F - YouTube
A buddy of mine has a gti that is not starting. he said the temp light has been coming on and the car would start to struggle. of course he kept driving. Today it came on and stalled out. Now the car turns over but wont start. I replaced the temp sensor (green plug) and it wasn't the issue. its a 1.8t with 80k on it. 2002. I am assuming its got to be fuel or spark.
View 15 Replies