C/K :: 1995 Chevy 1500 1/2 Ton Truck (350 / 5.7L) Started To Stall A Bit
Jun 19, 2009
Last week my truck started to stall a little bit. As I drove it a little longer, it stalled all the way out. It started back up fine but when I gave it some gas, it cut off. This happened several times. I popped the hood and noticed the throttle body was a little loose. Thinking air may have gotten into the system,I tightened it back up. I started it up,put it in gear and it seemed to drive fine and it started stalling again.
While I was on the interstate, it would cut off, cut back on,cut off and then cut back on. Finally it completely stalled out. I had to have it towed to my house. I hooked my code scanner up to it and it through code 44 (O2 sensor) and code 54 (Fuel pump relay or something like that). What could be causing my truck to run this way.
View 14 Replies
Advertisement
I own a 95 chevy 1500 with a 5.7 engine. The other day I'm driving home and my truck completely stalls out and has no power what so ever. To be more specific I didn't have lights, radio, key buzz nothing. Well by the time I got the under the hood I had power again and it cranked right up. I put it in drive and 5 minutes down the road and it stalls again with no power what so ever. I've been having problems recently with it stalling at stop signs/red lights but never with a loss of electrical systems. What this could be?
View 3 Replies
I have a 1995 k1500 when I turn the key on no lights on the dash if I wait 5-10 second you hear a click sound in steering column and the dash lights come on and starts fine. ???
View 1 Replies
This car started to stall sputter. I replaced the ignition module and it worked for while then nothing at all but still cranks. I checked all of the fuses and every thing was working. What I have found and i think this was the whole problem. The wiring harness that goes from the ignition module to the crank sensor, the wires were twisted and frayed and most likely grounding out on the frame and making the computer to shut down. So far after replacing the wires it started right up. Have not had a chance to take it for a test run to re learn the computer because my brake line busted.
View 1 Replies
Several years ago I had to replace the fuel pump - truck had about 100,000 miles. Within the last 4 - 5 months I have replaced the fuel pump twice and just today (about two months since the last replacement), the fuel pump has failed again. That has been the pattern now for the last several months. I have had the work done by one of the reputable car repair shops in town - they have also done work on my 2004 Impala with no issues with the repair. There must be something else going on besides just the fuel pump going bad. What would cause so many fuel pump failures.
View 16 Replies
My 1995 chevy c1500 cuts out at idle or the moment the brakes are applied to shift into drive. I replaced the passenger wheel cylinder and bled the brakes and it ran fine for a few hours, then the idle problem stated again. I have check the map senor and a few other electronic component as my mechanic said the problem " might be electrical."
View 6 Replies
New here but long time lurker. I have a 2006 e350 with 6.0, bought it from a friend not long ago. The work that has been done to it the last 50,000 miles is as follows.. New hpop, all new injectors, egr delete, sct tuner, stand pipes and dummy plugs. I had it for a week and would get a no start hot once in a while. This issue had become worse and the truck started to stall as the RPMs dropped. Reading here i replaced crank sensor and the stalling stopped but the no start hot continued. I took it to a local diesel repair shop and they did the following..
Use a test ipr (no change), replaced ipr pigtail (was cracked) air test (leak under pass valve cover) replaced stand pipes and dummy plugs on this side. They said no leaks and I was good. Truck worked as its supposed to for 1 day and the no start hot issue reared its head again. Took it back and now they say the hpop is bad. The pump that was put in about 50,000 miles ago was a bostech? do these go out? Sangauge reads good ficm, but seams ipr doesn't climb that quick.
View 14 Replies
I am doing a side job and this thing has a rough idle. I put the scanner on it and pulled code 43 ESC and a ritch and lean code from the O2 sensors. I know the O2 codes are probably from running rough. It has been a while but could the knock sen be the problem or the ESC itself? I looked for the ESC by the throttle body but didn't see it. I remember what they look like but this is a late model 94 are they some where else?
View 4 Replies
I have a 1996 Chevy Cheyenne pickup with a fuel injected small block that has 50k miles. Earlier this summer the truck developed a problem where it is very hard to start when cold (after sitting overnight or after sitting for many hours on my flat driveway). When the engine is cold (say the first start of the day) I can only get it to start by giving small bursts of cranking power to the starter. That is, it won’t start if I hold the key in the cranking position but is more likely to start if I give it a short burst of cranking power (when I hold the key in “start” position) for a second or two.After the first start of the day, the engine runs fine and subsequent starts are quick and normal. The “Check Engine” light is not on and there are no trouble codes…. Other than hard starting there are no issues with engine performance.
View 2 Replies
I got this truck from my step father, drove it from mississippi to washington (state) with minor problems. It's been sitting in my driveway for the last 6 months and I probably drive it once a week. I loaned it to my sister-in-law and she drove it for a couple of days with no problems. She went out one morning to take it and it wouldn't start, just cranked it for a few minutes and gave up. To make a long story even longer, I though it was fuel so I checked the pump, changed the filter, drained some fuel thinking water might have gotten in, ... to no success. I then started looking at electrical. Spark was getting to at least one plug. Pulled the distributor cap and cleaned it all up, replaced all the plug wires, and then tried starting it with the same results. (Oh, by the way, no check engine light so I assume no codes).
This goes on for a couple of weeks as it's in the driveway and I only pop the hood when it's not raining (we live just outside of Seattle). The other day I have the hood open, my wife decides to check on me since she thinks I'm talking to God and is wondering why I would use that kind of language when address a diety. I ask her to jump in and crank it while I pull a plug wire to see if I'm getting spark....again. Low and behold, the truck starts right up. I jump in to see if it's throwing a code and nothing. The thing is running great. I did notice that there is a ticking coming from the engine compartment and I realize the plug wire is still disconnected so I turn it off (with much hesitation) connect the wire, go back inside to start it and the thing won't start. I'm a private pilot and they say, if you're flying along and you do something and the engine stops, undo what you just did. So, I go back out, unplug the spark plug wire, and the thing starts right up. So, I start thinking, try another plug wire. I reconnect it, try another, and it won't start. So, what I figure is that it will only run when the second to the front cylinder plug wire on the drivers side on the engine is disconnected.
View 7 Replies
can i adjust idle on car, seems to be running faster without using gas pedal.
View 2 Replies
I have a 92 chevy pick up 5.7 with 159,000 miles. The truck runs and starts great but shortly after I bought it 3 years ago it developed a sort of misfire at higher rpm's, it's fine if I drive it normally but if I try to pass someone it will downshift then fall on it's face, (spit,sputter and slow down). some times I can feather the accelerator and it will come back again. I normally don't drive the truck in the winter but this week I was forced to use it and the cold weather is seriously affecting it, it took forever to get it up to 70 mph after getting on the highway. once up to speed it will do 75 all day without an issue.
I've replaced the plugs, wires, pulled the throttle body and cleaned it as the port for the pcv valve was plugged solid with carbon. I have not replaced the cap and rotor as they seemed to look fine. I have not checked the fuel pressure because it will break the tires loose upon take off and I don't think that would be possible if the pressure was low, would it?
View 5 Replies
I am trying to get some advice on a diagnosis for a transmission problem i'm experiencing with my vehicle? It's a manual transmission and the sound i am hearing is when i shift gears is a loud whirling grinding sound. It's really loud in 2nd 3rd and 5th and doesn't stop.
View 1 Replies
My brother's 1995 chevy lumina 3.1 engine has been dying while braking for a stop and while reversing. Has replaced fuel filter, map sensor, throttle sensor, o2 sensors and still no change. He says he doesn't believe a tune-up is the cause either.
View 8 Replies
I bought this van (1995 chevy van 20) last year and the rear end made some sounds but not as bad as its now.
So, after buying it I decided to open up the rear end and inspect for any damage to suggest it needs repairs. No signs of metal chips, nicks, or any wear on the bearings and gears. After a while of driving it I decided to remove the carriage and pinion from the rear end to give it a close inspection. After doing this and finding no clear sign of war or damage, i decided to replace the carriage barrings to see if that made a difference. After placing the new bearings back on the carriage, pinion back into the rear differential, and trying to do it all by myself, i lost the marks i had placed on the carriage bolts and clamps since I had little time to get it back together.
After that I had no other choice but to place the clamps bolts where i could estimate they belong. I was done, then drove it and some of the noise went away but a grinding sound on decelerating emerged. Well, now that sound is gotten worst and its more like a grinding sound. I can assume that not placing back the bolts and carriage clamps back changed the position of the carriage relative to where it was, but am not 100% sure. how can I correct the positioning of the carriage? if that is not the issue what test can i perform to find the culprit?
View 18 Replies
I've got a noise that has me puzzled on my 1995 Chevy C1500 (2wd). I hear a mid to high pitched noise when I'm driving at between 45 and 55 mph (70-90 kph). It varies in pitch depending on the speed I'm going, starts at around 45 and goes away above 55, and also tends to go away if I lift off the gas. The sound occurs in any gear, but always at the same speeds. My leading suspect is the differential, but I haven't ruled out anything yet. I pulled the differential plug and the fluid isn't very dark.
View 7 Replies
My 1995 chevy camaro has been overheating. at first i thought it was the thermostat sticking because there was no spewing or smoking so i changed the thermostat and my car was still over heating. I finally found out that the water pump was leaking fluids. so I changed out the water pump and filled it full of coolant. i turned on my car and within 10 minutes the gauge went up to 260 degrees and went down a little bit but stayed around 260, there was no spewing or leaking or smoking again. I was thinking that maybe now it could be the sensor but im not sure.
View 1 Replies
I have a 1979 chevy g10 sportvan with a 305 engine. Some time ago the van started to cough and die when going up a hill. It would not start at all while on the slope but if I rolled it back to a level surface it would start right up. I found that if i filled the gas tank up, the problem would go away. I figured that i had a problem with the sending unit, maybe the tube that runs toward the bottom of the tank was corroded in some way so that it would only suck gas when the tank was full to a certain point. So I kept the tank at least half full with no problems. Then the problem returned when the tank was 3/4 of the way full. I figured that the sending unit was getting worse. I removed the gas tank and removed the sending unit which looked fine. I was disappointed.
I began to drive my farm truck around and the van sat for awhile- maybe 6 months. My farm truck finally died, so back to trying to get the van running.I put a new sending unit in since i had the tank out anyway, put about 5 gallons of gas in it and headed for the nearest hill. Seemed to work just fine. Problem solved, right? After about 100 miles of driving the problem is back again. I figured o.k. the carb float must be getting stuck, so i have removed the carb. I found that the fuel filter was crushed/ installed improperly, it was just kind of smashed and twisted looking when i took it out of its housing. Yes i am the one who did that and yes i am an idiot. I cannot exactly remember if the problem existed before i changed the filter last time, but i suspect that it did. I have the carb apart right now, it certainly needs a cleaning, but the float did not seem to be hung up at all. The van has a mechanical fuel pump. I imagine if its not pumping enough pressure it could cause it to stall or bog on a hill, but it won't start at all on a slope after it dies. It starts immediately on the flat.
I guess my questions are these: Could the filter problem have caused the stalling problem? What else in the fuel system could be failing due to gravity? Should I be looking elsewhere for the problem?
View 2 Replies
Fuel injected 429 (same as 460). Will run for 10-30 minutes then stall and not restart until 5-60 minutes later. Has fuel pressure at rail.
View 6 Replies
For the last 2 years 1995 ranger 2.3 will run great but every 1-3 months will just stall. Will than try to start it for a couple of minutes and in 1-8 minutes will start back up again as if nothing was wrong and then be fine for another week, month, 2 months etc. It has never happened at first start up in the morning but at times will stall 2 minutes after start (at traffic light of course). At times will turn off to run into store, come outside, no start, try for couple of minutes and then starts up fine. Changed out fuel pump, etc, etc. Biggest problem is no codes and, of course, when mechanic looks at it nothing is wrong.
View 4 Replies
I have a '95 Chevy K1500 5.7 and am wanting to install a freeze plug block heater, but I'm having problems knocking out the existing freeze plug and would like some hints. It is located directly behind the oil filter, so I'm having problems getting enough leverage.
View 19 Replies
