Camry :: 2002 - Check Engine Light On / Code P0440
Sep 25, 2014
It just so happens that I got my letter from the DMV telling me I needed to get my new tags, and this is an emissions test year for my car. I was buys the last few weeks so I figured this would be a good week to do it. Yesterday.......check engine light comes on. How does that happen???
So now I'm on a time crunch. I went to Advanced Auto this morning and they checked the code. It's P0440, an Evaporative Emissions code. Any thought on what that me be, or any checklist as to what to check first? I'm fairly handy, but know nothing about cars. I'm sure I can figure it out with some instructions.
Summary: Got a check engine code of P0440, Evaporative Emissions. On a time crunch because I need to get an emissions test done. I can probably fix it myself with some direction.
View 2 Replies
Advertisement
Check engine light was on for some time when I had filler neck and cap replaced. Computer sensors did not re-set until 501 mile mark, when light came on again. Checking the web, I find that some who appear to have knowledge of problem say it could be hoses, sensors, valves, or evap canister--the charcoal canister.
Mechanic who did original smoke test and recommended replacement of filler tube wants to replace evap canister without checking anything else. What should I do? At wits end, and car needed to pass inspection 2 days ago. Car has 157,000 miles or so...
View 9 Replies
I have a 2002 Toyota Camry V6. The warranty expired in Feb 2007. The car has only 67,000km.
The check engine light came on and the code is P0770, Solenoid E malfunction. The problem was first reported at 43,000km, when the car was still under warranty but only a transmission flush was performed and the code was reset.
I wrote Toyota and after almost two months they told me they do not cover it because is out of warranty and I do not qualify for the Goodwill program. I tried again to tell them that instead of fixing the root of the problem they temporarily covered it, but again I got a NO. No comments about the mileage, time, etc. Just the car is out of warranty and I'm out of luck.
View 8 Replies
I have a 2002 v6 Camry with over 270k on it. Today the Check engine light came on while driving on the freeway. When I got home I used my scan tool and it gave me the following codes.
P0128, P0440, P0446 and P0440, P0441, P0446 pending.
I understand that the 128 has to do with coolant temp and that the other codes are evap system related.
What I'm trying to figure out is what might have caused them to all occur at the same time. I know once with my 98 Camry it threw a P0125 which had to do with coolant temp issues but it also threw several other codes for a bad 02 sensor and the 125 was just a false code (replaced the 02 sensors and they went away). If this 128 is possibly a false code or if I also have a bad thermostat/sensor on top of an evap system issue.
Also. coolant level is good and I checked the gas cap and insured it was on tight, reset the codes and am waiting to see what comes back.
View 1 Replies
I was looking for some diagnosing the problem with my car. I've already gone and put one of those autozone scanners on it, and it gave me a very vague idea of what could be wrong. It pulled a P0440 and P0507 code. I go to work and school full time so I don't have the time to be poking around at everyone of those possibilities.
The check engine light came on a few months back, the acceleration has been bad since then, but it just recently started running worse. While accelerating the car jerks horribly, but then will smooth out if I give it more gas or let off a little bit.
View 2 Replies
Replace this when they got a code p0440? If so, which way did you go about replacing? if so, did u have to drop the tank or from cutting from underneath the seat? Is this the same location as from the 1st gen is300?
View 12 Replies
Check engine light on and code is P1451. I have been told its one or all four things:
1. Gas cap,
2. Evap Canister vent solenoid,
3. Evap purge solenoid,
4. Evap canister.
I am trying to fix this problem on the Taurus. I have changed the Gas cap and this did not solve the problem. The other three things on the list: Are these three separate things? Or are they part of the same thing?
View 1 Replies
I have a 2002 4 cylinder Camry, and I've been having trouble with the EVAP test completing. I've been running the EVAP test to the letter, with no success, so I figure the problem might be dependent on something else not completing.
I used to get the occasional check engine light for loose gas cap. So a few days ago I intentionally left the gas cap VERY loose (it's essentially just sitting in the filler nozzle). But I'm not getting the check engine light. I think that the gas tank pressure test may not be running, and that may be why I can't get the EVAP test to complete successfully.
Conditions: The gas level is about 1/2 full, and the ambient temperature has been around 20-35 degrees F.
I'm having a hard time searching. Most search results deal with how to resolve the loose gas cap problem. The check engine light is not burned out... it comes on briefly when I start the car!
View 5 Replies
My wife's car has 83000 miles on it. We bought it as a factory certified pre-owned vehicle with about 1800 miles on it and it came with the warranty. For the last two years the check engine light comes on with code 441 I don't worry about it till time to get inspection sticker here in Texas. I have been about to reset the computer and drive it till the computer is ready to be inspected and it has passed for two years. Now it won't reset and I have tried to test the vacuum switch and it seems to click when I apply voltage but light won't go off. This code can cost up to about 2000.00 to try and detect. I am not interested in having the dealership keep guessing on my dime.
View 2 Replies
I own a 2003 Camry LE. I went to Autozone to find out what the check enginge light was for and was given P0031. When the service person checked it out on the computer he said the probable causes were:
1) open or short circuit conditions
2) poor electrical connections
3) failed oxygen sensor
4) EFI relay fault.
I asked how it could be narrowed down and he said it I would have to get the car checked out.
View 14 Replies
I'm getting a P0128 code on my 2003 V4 Camry. Autozone diagnosis says it's either
a) coolant low level
b) sensor not working correctly
c) thermostat not working correctly.
As part of 90k mile check about 3500 miles ago, the mechanic replaced the coolant. I didn't check the coolant after he had replaced it but I just checked it today and it's about 1 inch below the full level. Is this normal coolant usage considering that it's been about 3500 miles and 3 months since it was last filled?If the coolant level is okay, then how do I figure out if it's the sensor/thermostat?
View 10 Replies
2001 Camry 4 cylinder. Check engine light came on yesterday. Advance Auto pulled out the code P0446 for the evap. emissions system vent circuit.
The car has no symptoms other than this and is current on all maintenance, but obviously it is a 10-year old car and so it goes.
View 9 Replies
So I had a serious runability problem back in 2012 with code P0302 (misfire in cylinder 2) and the car was barely running. I changed the spark plugs, which didn't fix the issues. Then changed the coil, which fixed it. URL...But I was a little lazy back in September 2012, the old spark plug wires looked like they were still in great shape, so I left the old wires on. I think they were the original factory wires, they had the numbers of each cylinder printed on the side. Very nice wires!
Fast-forward to the present. Car starts running poorly with a blinking check-engine light. Not good! I check the code and it is P0306, misfire in cylinder 6. So my first thought was: OK, probably time to change the spark plug wires!I changed the spark plug wires. I purchased AutoLite Professional Series wires at Advance Auto Parts, part 97047. URL...Sure enough, the number 6 wire looked like it had a little corrosion inside the end that connects to the spark plug wire. It looked like I was on the right track! Changed the spark plug wires, and ran it. It still sounded like it might be missing on one cylinder. Just a quiet ch-ch-ch-ch-ch-ch at idle. I took it for a test drive. It ran OK at low RPM's, but had no power. When I tested some hard acceleration, sure enough the check engine light came back on. Tested the code and it was P0306 again. Conclusion: not fixed yet.
OK, maybe the spark plug wire was the problem, just the plug got fouled because the wire was bad. I purchased a replacement spark plug for that cylinder only. AutoLite Double Platinum as recommended elsewhere in this forum. Removed the old plug. I'm no expert, but the old plug looked fine to me. Installed the new plug. Tested it again. Still sounded like missing at idle ch-ch-ch-ch-ch. Test drive, OK with low RPM, no power. Tried hard acceleration, got the blinking CEL again. Conclusion: still not fixed - darn it!
Now remember, I just changed the coil back in September 2012. I had replaced it with a coil from AutoZone. The first coil had lasted ten years. So it couldn't be the coil again this soon, right? But... just to be sure, I went ahead and changed the coil again. I called AutoZone and happily it was still under warranty. The previous coil I had purchased came with a 24-month warranty, and I was on month 23 !!! Sweet!AutoZone also told me if I did a warranty replacement of the coil, the new one would come with a lifetime warranty instead.The part number of the coil at AutoZone was part C1312, Duralast Ignition Coil.
Before installing the new coil, I put a little Dielectric grease around the top inside of each connector on the new coil (7 total, six spark plug wires plus the electrical connector). I think this was recommended in my Haynes or Chilton manuals.I am a tall skinny guy with long skinny arms. So I was able to replace the coil without removing the cowl. Last time I had to remove the cowl (to do the intake manifold isolator bolt repair) the cowl had cracked, also some of the clips holding it down broke. So I didn't want to remove the cowl unless necessary. It turns out with my long skinny arms I can lay up over the motor and reach back around both sides of the intake manifold to reach the coil. It is a reach, but it was possible for me to do the job that way.
I removed the three bolts holding the old coil in place. Then I was able to slide the new coil back in there, around the driver's side of the intake manifold. I transferred over the spark plug wires one by one from old to new (as recommended by another poster) so I wouldn't get confused which was which. It worked well to transfer the rear three first. That hold the new coil near the correct location, and gave me more slack to move the old coil further out of the way.Next step was to remove the wire connector from the rear of the coil pack. It didn't want to release. I looked at the old part (from 2012!!!) and there was a little plastic nub back there to lock the connector in place. It looked like there was room to work in a small screwdriver back there to release the lock. So I wiggled a short flat-head screwdriver in back there (with a wide head) and it released. Then I was able to easily remove the connector.
Then I had more slack to move the old coil further out of the way, toward the drivers side and front of the vehicle. And then transferred the last three spark plug wires to the new coil.Then to secure the new coil in place, I carefully installed one bolt by hand, leaving it loose to allow for final adjustments of position. Installed the second and third bolts loosely. Tightened the three bolts finger tight using a short (3") extension and 7mm socket (1/4" drive). Then snugged them very gently using my small 1/4" rachet. The small 1/4" rachet was a perfect fit using the 3" inch extension and the small 7mm socket. Remember you just want the bolts snug, do not over-tighten them.
When I went back to AutoZone to process the warranty return, they had to do some fancy work with their computer to get me the lifetime warranty on the new coil. By default it would just assume the rest of the original coil warranty from 2012 - which was just about to expire. So they made it right for me - but only because I specifically asked about it. By default, the guy had already rung it up their "normal" way, which would not have extended the warranty for me.Another thing that was strange was back in September 2012 when I replaced the original coil, it had worked well for ten years or so! Also, the bottom of it was clearly cracked, so it was easy to see that it had deteriorated and needed to be replaced.
View 1 Replies
Suddenly today, I get a "Check Engine" light while driving. Scangauge II says it's a P1430 error. I found two different suggestions, but where these are located on the car.
P1430-Electric Air Pump secondary Failure
P1430 -Vacuum Sensor for Adsorber and Catalyst System Circuit Malfunction
View 13 Replies
Car: Toyota Camry 2002 .. Mileage: 150K
Symptom:Check Engine light went on a few days ago.
Checked codes and got these (3):
1) P0420
2) P1310 and
3) P0420 P ("Pending" ?)
I also checked I/M Readiness and got these suspicious-looking values:CAT: NOT RDYEVAP: NOT RDYO2S: NOT RDYH02S: NOT RDY
NOTE all the other I/M values were N/A
Researching the Codes, it sounded like Ignition, and possibly the O2 sensor on the Catalytic Convertor. I had just had some engine work done by the dealer -- actually, replaced spark plugs -- so I figured to go back and bitch him out for screwing up my car.
A few days later, before I could engage my Rage, I went back and re-scanned. First I noticed the CEL was now OFF. Scanning, I now I get "NO CODES", and all the I/M values are now N/A; No more "NOT RDY".
What do you all make of this? Should I be concerned now that the CEL is Off, and I get No Codes with a scan?Or maybe I should take it to AutoZone for their free CEL diagnosis -- would their machine be more thorough than mine (Autel MaxioScan 300)??
View 4 Replies
2002 Camry 4 cylinder. I've replace the o2 sensor the one in "Bank 1". I've cleared the check engine light three times now and it still comes on about 30 plus miles. Do I need to reset the ECU? Or replace the catalytic converter?
View 11 Replies
Today my check engine light came on and the code is P0712. When I drove off from the parts store, the check engine light suddenly went off. What should I do at this point? What are the most likely problems/solutions.
View 1 Replies
I recently replaced the spark plugs on my 2002 Camry SE V6 (Gen 5). Let me just say that it was INCREDIBLY DIFFICULT to reach the rear 3 plugs as they sit underneath the intake manifold, way to the rear of the engine compartment. To reach those, I had to unplug some wires reaching on top of the engine, then loosen the intake manifold.
Along the way I broke a tiny air valve that sits underneath intake manifold, and replaced it right away, before starting the car.
When everything was put back together, the car started wonderfully, only to notice the engine light come on. I had the codes checked at the dealer and they indicated a malfunctioning Catalytic Converter and A/F Sensor and some other emissions stuff. Later that day, the VCS/TRAC OFF light came on as well. The service guy at the dealer said those typically come on together with the Check Engine light, which sounds like something he pulled out of somewhere!
The car drives well, no hesitation, no weird behavior, but has no traction control, naturally. While loosening the manifold I had to use a little force to flex it out of place. My guess is that it I may have yanked something out place: may be a wire issue, or a sensor.
View 13 Replies
My 2005 Camry check engine light is on. The trouble code is P0138, bank 1 sensor 2 oxygen sensor. Engine is the 2AF-ZE. Not a California emission car. Car is Japan built. It has two O2 sensors. What is the correct OEM part #? I believe it would be a Denso?
View 2 Replies
This issue pertains to a 2006 Camry LE 4-cyl.
My check engine light came on - code P0032 (upstream O2 sensor). I bought a new sensor from O'Reilly Auto Parts. After installing the new sensor, the car would jerk while accelerating. This continued to happen until roughly 30 miles or so when the engine light came back on and the jerking stopped! I re-scanned the car and it showed the same error - P0032. I then erased the code, and the jerking issue resumed.
I assumed this was caused by a faulty O2 sensor. I returned and got another one. Same issue.
Is this the result of not getting an OEM sensor from the dealer? Or is there something else I should be worried about?
View 4 Replies
I own a 2002 Solara V6 with over 300,000mi. The check engine light is on and affecting the tracking control. The dealer cannot find the cause without replacing many parts costing lots of money.
View 2 Replies
