Camry :: Wheel Bearing Noise Which Becomes Faster When Accelerate
Jan 29, 2014
I have a noise I think maybe the front end but not sure it sounds like a wheel bearing noise it's becomes faster as I accelerate it does not increase in noise and by the time you get to 20 mph it disappears, it also disappears when ou tap the brakes or barely push the brakes I had the brakes inspected it's good had the wheel bearings check out even though they said it's a sealed bearing unit they did their test and the wheels made no noise...My car is a 2005 Camry 4 cyl.
View 11 Replies
Advertisement
I have a 07' V6 SE and have a nasty wheel hop. Went to the track and ran 15.0@95mph all night because I can't accelerate faster without the nasty wheel hop (temp was 90 with lot of humidity). I would like to go to the track again, but before start making some mods (intake & complete exhaust) I want to get rid of the excessive wheel hop.
View 14 Replies
I just bought a used hyundai santa fe sport 2.0t. i noticed it is fairly loud inside compared to my 2011 sonata. I don't know if im hearing tire noise or maybe a wheel bearing type noise. It's coming from the rear and gets louder as I go faster. I'll admit O am paranoid and probably making this sound worse than it is.
View 12 Replies
Two days ago I started to hear a strange engine ticking noise. This is not the normal sound of the injectors pushing fuel into the engine, i know what that sounds like. This is far louder. And when I start to accelerate, the ticking becomes faster. When I cruise at a steady speed, the engine starts to sputter until I press on the gas or brake.x I took it to my local dealer and they ran codes and did an oil change. The guy told me to drive the car around for a bit and the noise will disappear. They also told me that if it did not disappear then I am basically screwed because it could mean that "my valves collided with my pistons due to over exceeded engine speeds" I will post a picture of the code and a video of the sound. [URL] ....
View 13 Replies
So on my girlfriends 2000 echo I get the classic bad wheel bearing noise/vibration on the front left (driver side) wheel. Worsens under load (right turn) and goes away when unloaded (left turn). I've replaced left side bearing, CV axle, brake rotors/pads and the noise still persists. My next thought is maybe the ball joint but humming/vibration tells me something out of rotational balance. Bearing in the transmission? I don't know. I'm stuck.
View 5 Replies
Just had an oil change and during inspection they noticed that the drivers side wheel bearing is starting to go. They brought me back in the shop and I was able to feel the play in the bearing myself. Only a matter of time before it needs to be replaced.
How to replace the front wheel bearing/hub assembly? I don't have a press for the bearing itself so I'm assuming I can just replace the entire hub assembly. I have already replaced the drivers side rear hub assembly about 1.5 years back due to a bad bearing
View 1 Replies
Camry 2004, 50,000 miles
Last week my car started to give out loud thud noise from the rear passenger side wheel and shook as I accelerated. My wheel bearing was bad and leaking. Replaced it. The loud thud noise and shaking are now gone.
However, I hear a constant very low rattling sound from the same wheel when I cruise above 40 mph. Time to time I also hear a loud rattling tin can sound lasting for two seconds, and it mostly happens when I make right turns.
View 1 Replies
My girlfriend and I just bought a 2011 a few weeks ago. We test drove it a couple times ourselves, and had our mechanic take a look at it and drive it also. Everything looked and sounded good. Not sure how much it matters, but it's a Certified Used as well.
A couple days ago, returning from a 45-minute drive which included some short stretches of gravel road, I noticed an oscillating sound. It's definitely not a noise that was there when we bought the car. Unfortunately, my cell is apparently bad at capturing audio, so hopefully my description will be enough.
The noise is very faint, almost inaudible, at low speeds. Between 30 and 35 mph it gets much louder, peaking at about 33. There's some vibration through the accelerator pedal also. Above 35, it fades pretty quickly and I can't really hear it at 50. The sound itself is 3 beats on, 1 beat off, about every second. There's a slight difference in pitch between each beat.
If that isn't enough to go on, let me know and I'll give the recording another shot and upload it if the noise is audible.
View 6 Replies
So I let my son drive my car for the day because i wasn't doing anything. Now once he gives it back i started driving and now my car drives kinda bumpy and makes a thudding noise the faster I go. now i confronted my son(He's 19) and he told me he went to fast over a hill. What seems to be the problem.
View 14 Replies
So after doing wheel bearings in the car. both front and back. I'm still getting the "wheel-bearing hum" sound if you will. Don't know how this can be possible with all brand new wheel bearings and hub in the front passenger side. other hubs were fine. I do need tires which will be ordered soon/ alignment im sure.
View 5 Replies
I took my car in for what to me sounded like a wheel bearing noise. Dealer thinks the culprit is brakes need to be replaced. In addition to needing brakes I was told i need a throttle body service (service agent says it's needed every 15k for carbon buildup) and also a fuel tank vent filter ("needed every 2 yrs") are these legit repairs I should perform or is this a dealer shake down?
View 15 Replies
I think it is cv joint not sure. [URL] .....
View 2 Replies
Have a whirring/wheel bearing metallic rubbing noise at 70-80 mph, 6th gear (manual transmission). It's hard to pinpoint the location but it's from the engine area! I heard about water pump failures but thought I'd hear that all the time not just at speed... MKVI GTI ...
View 15 Replies
Changing wheel bearing on mk4. makes noise when i turn to the right. what side is bad? i like working on my own car but this might be out of my hands.
View 12 Replies
So my front right Wheel bearing is making noise and its a used Knuckle so its w/e. Guess ill use tonight to do all my bushings and fluids n stuff.
View 6 Replies
Got a "wheel bearing noise" emitting from my 2007 Sonata with a 5spd manual. I've replaced front and back wheel bearings with no noticeable change in the noise. I then rotated the tires with same result ...no noise difference. Lastly after much reading I was convinced one or both of my cv axles were at fault so I replaced both of them and unfortunately the moaning roaring noise is still very much there. The only thing I can think of at this point is that one or both of the transmission's CV support bearing is bad. I've depended on this car for a long time and it has given me great service but with 170K miles on the clock I'm afraid the tranny is going to give out and strand me in possibly a unsavory part of town..
View 4 Replies
So just to sum it up. Past few days I had been hearing a grinding/clicking noise from my left front tire. I had an accident on that side a few months back. Went to the mechanic and they said it is most probably the wheel bearing and possible the hub also.
They took it apart and changed the wheel bearing. After two days of getting the wheel bearing changed the noise is back. It is not nearly as loud but it is definitely there.
What it could be? Could it be the hub itself? I have a 07 Sonata with 100k+ miles on it
View 2 Replies
So my ranger was having a textbook wheel-bearing noise at around 50mph....when I turned to the right the noise went away implicating a passenger side wheel bearing.
So I replaced both of the hub bearings on the pass side and noticed that the front axle shaft u-joint right behind the spindle was really bad and was going to change it but couldn't get the spindle off so I said screw it.
Took it for a drive and the noise is still there. Could a worn u-joint possible replicate a wheel bearing noise? I am used to them making a clicking/popping noise while turning when they're bad, but not a whirring sound.
1993 ranger 4x4 manual locking hubs.
View 4 Replies
I recently bought a '97 Volvo 850 sedan. It is not a turbo. It starts up fine. It goes in reverse fine. It accelerates to about 10-15 mph fine. But when I accelerate faster than that, the rpm's go up and the car coasts. After about 20 minutes the car drives fine and it doesn't rev high. How to find what need replacing?
View 1 Replies
Since the Prius is my wife's primary car, I can go a long time without driving. I recently have been driving it more, and it seems to me that it has the sounds of a failing wheel bearing. Between about 30-40 MPH there seems to be a distinct rotational noise that sounds to me like a loud wheel bearing from the front end. The sound seems to get quieter as I go faster, and at 60 mph + it seems normal.
My wife didn't notice any difference, but she drives the car everyday so maybe she didn't notice the gradual increase in noise. I know it's not tire related, because I just swapped tires. When I did, I didn't feel any play in the front bearings or feel any roughness when the wheels were rotated.
View 19 Replies
2006 Ford Focus with an ongoing wheel bearing issue. Earlier this year I heard a repetitive whirring noise from the back right, figured it was a bearing, brought the car in for repair. The shop confirmed and replaced the bearing.
3 months later, I heard the same noise. I brought the car to a different shop (I had moved since) and they confirmed that it was the same wheel bearing that had just been replaced. They said it may have been faulty. They attempted to repair it, but the noise persisted. They actually ended up putting the new bearing on the driver's side rear and swapping out the old bearing that was on the driver's side with old one on the passenger's, which is the only way they could get the noise to stop entirely. (This confused me)
Fast forward two months and the noise is back on the same side - passenger's rear. The shop is telling me that it is unrelated since the new bearing was technically put on the other side, however, I am thinking that the same thing keeps happening whenever any bearing is put in the same spot (passenger rear). My question is as follows - what could be happening in the passenger rear that would cause bearings to continually fail?
View 1 Replies
