I am having an interesting sound coming from my rear brakes when I stop from reversing, for example, when I'm pulling out the drive way or a parking space. It kind of sounds like a loud "hum" that lasts a spit second, until the car actually stops. I changed the rear brakes and rotors about 1500 miles ago.
2006 Elantra Limited, 88,XXX miles.
I have a 2004 Elantra GLS. My left rear brake was hanging (wheel was very hot to the touch after driving, while other wheels were not), so I had a friend check the brake pads. We decided to replace the pads and rotors. While doing so, the parking brake seemed stuck in the on position, so I opted to have him disconnect it completely until I could afford to replace it. I had used it for the first time about 2 weeks before I noticed the hot brake problem, so we figured that must have been why the brake was hanging.
My friend replaced the rotors and pads, put some penetrant/lubricant on the piston of the caliper and reassembled the brakes. He did use the special tool to spin the caliper in when putting the pads on, however he didn't know that was necessary and tried to force them in with a C-clamp first.
Now, I seem to have two problems:
1. The left rear brake still hangs sometimes. I will drive the car and when I park it I can feel the heat coming off of the left rear wheel. It is extremely hot, so I know the brake is hanging (even with the parking brake disconnected). What is the problem here? Is the caliper bad? Would replacing the caliper solve the problem? Does the parking brake have to be connected to stop the caliper from hanging up?
2. My second problem is the pulsating of the brakes. I am afraid the rotor is warped because of the heat, or maybe he didn't clean everything well enough before he put the new rotor on. How can I figure out what the problem is? Is there a way to check a rotor to see if it is warped? Could there be another reason I feel the pulsating brakes? By the way, the brake fluid is full.
If the caliper needs to be replaced and I can leave the parking brake disconnected, are there any special instructions my friend should know about before working on this? He does work on a lot of cars and rebuilds cars to sell, so he is pretty knowledgeable. I think the only thing he didn't know about was rotating the piston. I would like to provide him with detailed instructions if necessary.
This is my first time working on drum breaks, all the repair manuals and videos don't make it look too bad. I did have a question about the parts required to replace the rear breaks.
Assuming these breaks are very worn. What parts would need to be replaced in a typical break job.
The pics below are what I'm planning on buying:
Shoes
Rotors
Drum
Hardware Kit
Is there anything that I'm missing?
I have a 2003 hyundai elantra gt. All the lights and bulbs work, except for the rear left brake light. I've replaced it twice now, and used a bulb I know was good, so the problem is not a bulb. I checked the fuse, and the fuse is ok as well. When I measure at the bulb socket with an ammeter I get around 20 mA which I assume is too small and I assume there is a loose wire somewhere.
View 2 RepliesI noticed the rear parking cable's one end hanging. Not sure how to connect it. Appears a part is missing.
View 7 RepliesTopped off my brake fluid 6 months ago. Last week my brake light came on. I checked and I only had half the fluid left so I topped it off again. Today I went out and there was some kind of oil near my rear tires and my light came on again, needs more brake fluid.
View 6 RepliesHave to replace both rear brake lines, I can't find any information about doing the job. I need to know what size the lines are and what type of flair is on the ends?
View 2 RepliesI have a 2013 Elantra, owned since new... I recently started hearing a knocking sound coming from both front wheels while turning in reverse. I have yet to take my car in to have it looked at, if I can do it myself I will but I'm not sure where to start.
View 3 RepliesMy car literally started doing this thing where it sounds like a vibration or humm when putting my Elantra into reverse.
View 2 Repliesi have a 2002 santa fe which will not go into 5th and reverse So i have put a new clutch in and new oil ....
View 8 RepliesIt only really happens when the car has not been warmed up, like first thing in the morning. Aside from the noise, the car shifts and drives normally. Noise just developed, 28k on the car, it is a 2012 elantra. As I shift from P to R while backing out of my garage there is a metallic clink/ping as the transmission engages.
It is not a CLUNK sounds, it is deff more on the side of a metallic clink...
My 04 elantra starting acting up yesterday. It has started jumping/ rocking entire car when putting in to reverse. What might cause this problem. It is hard to describe what it is doing being I know nothing about cars. It is a large jolt when going into reverse.
View 4 RepliesHow do you replace the reverse light switch on a 2002 Hyundai Elantra manual transmition?
View 3 RepliesI have an 01 Elantra Gls with perplexing issues. The car starts at 3000 rpms, and continues to bounce between 2k and 3.5k in both park and neutral. when I put it in reverse i get a very hard shift. It actually jerks the whole car. in drive and reverse, it idles around 1.5k it hesitates quite a bit to accelerate. All fluid levels are right and don't smell burnt. it takes me 10 mins to put 4 gallons of gas in. if i pump too fast it shoots back at me. i randomly smell gas while driving. Im hoping these problems are a couple of issue I can handle at home. i just wanted some input before i buy the manual. thinking vacuum lines maf sensor.
View 7 RepliesMy car has been making this grinding noise for the last 2 months. It happens when I put the car in reverse gear and slowly release the clutch. Rarely happens also in 1st and 2nd and 3rd and is always at the beginning of the transition when I am letting the clutch go. I do not know if it is the transmission, the clutch or any other part. I drive a 2002 Hyundai Elantra 5 speed manual transmission with over 120 k miles
Here is a link to a video I posted so you can hear the noise it makes : [URL] ....
I am installing a backup camera and want to hook the power of the backup camera up to the reverse lights power wires.
Which color(s) the reverse light wires are in the trunk?
08 ES350 with 52k miles has a grinding sound in reverse. Brake pads were inspected - ok. Suspect that parking brake shoe is worn. Any tips on teardown/replacement ?
View 2 RepliesMy rear brake makes a whining noise when I go on reverse. I know is brake related because while on reverse, if I barely touch the brake pedal the noise goes away. But without touching the brake pedal whines and sometimes loud and is embarrassing.
View 5 RepliesI have the following codes:
P0705
P1529
It looks like P1529 is caused by P0705. P0705 is the neutral range sensor. I purchased the sensor and replaced it. It is aligned correctly and I am still having the same CEL and codes.
What the car doing: The car jerks into reverse and drive. The dash does not indicate what gear I am in (PRNDL).
When it drives, acceleration is very slow. I believe the car is "stuck" in third gear. I've heard of fail safe mode?
What I did: This problem started when I changed my stereo. I did three bad things which may have caused this problem.
One, I had to put the car in "L" to get the dash off. I left it in "L" for a while then I tried starting the engine while it was still in "L".
Two, when I reinstalled the center console I swapped the wiring for the hazard lights and the rear windshield wiper (GT)
Three, I wired the dash illumination positive and negative together.
The cluster's backlight does not come on anymore and these codes came up. I checked all fuses and they are good. Where to look for a possible shorted wire that can be causing this?
I'm having trouble with the automatic transmission in my 04' Elantra, it acted like the speed sensor was failing, but later the same day it lost all gears, forward and reverse. after turning the car off and sitting a while I started it back up and had gears again, but the trany is making noise. Fluid level is ok.
View 3 RepliesI have a slight squeal from the left rear brake when in reverse. Doesn't do it all time and never when roads are wet. I disassembled the caliper and all looks good. I replaced the pads about a year ago and the noise just recently started, so its hard to blame that. I did not use the brake anti-noise lube......but I never have.
View 2 Replies