I have a 2005 f250 6.0 diesel. I have changed the 2 fuel filters, fuel pump, sending unit (was broke off in tank )and installed the blue spring fuel pressure regulator kit. My truck will run for a few minutes loose fuel and kill. Could this be a sensor or computer problem
View 12 RepliesBeen chasing my tail and can't figure out an electrical issue. My issue is that I'll drive for about 20-30 min and the truck will shut off while driving. I'll pull off the road, let it sit for 10-20 min (cool down) and It will fire back up and go for another 15 min or so. Sometimes it will glitch/wig out when i try to start or not start....
I've replaced the following and monitored everything on a scanner.
-cam sensor
-crank sensor
-2 new batteries
-flashed the ecu
05' F250 6.0 King Ranch 4X4
Started my 2005 f250 powerstroke, idle about 15 min and died like I turned key off. Hooked up scan guage had no flp, fmp or syc ipr and icp was good. Checked ficm relay and fuses and all checked good. Next morning went out and it started flp, fmp, sycall good. Idled about 1 hr and died again same bad readings. Messed with relays and wiring to ficm, it started and died after 2 min. No start again, next morning still no flp, fmp. Went out again in afternoon and everything was good again, I did nothing to it from am to pm, was loading my pistol they shoot horses don't they. I have new batterys, I changed the ficm power card last summer for low fmp. When it is running everything looks and sounds good no miss.
View 14 Replies2005 F250 4X4 6.0 .. Why my truck just stopped going when put in gear and the TOW/HAUL light just kept coming on, without pushing it 2 days prior? Now it will not go anywhere, starts great, gas pedal works because RPM's go up when pushing! Just will not go when put in drive or reverse! What else I can do? I replaced cylinoid B in the transmission, speed sensor, and brake switch.
View 14 RepliesMy 05 F250 CC 4x4 had a problem where it was wondering to the right.
I had the front end checked out and they said everything was good and within spec but they discovered a bad tire (internal belt separation).
Had two new front tires installed/balanced and the problem seemed to go away for a few months.
Now the problem is back even with the new tires. Could the steering box cause this or is there something else I should be looking at?
I have a friend with a 2012 F250. The truck has 100K miles and it does idle for extended periods. The other day his check engine light comes on so he took it the shop. They had not told him anything yet, but they did tell him that he had about a gallon to much oil. They said it was fuel.
View 7 RepliesI have a 2005 Ford F-250 Powerstroke. At times when stopping at light or for any reason, I give it gas but it does not want to go. It's like it is not even registering that I am pushing the pedal. I shift it into neutral and rev it up then switch it back to drive and it goes and puffs out smoke. What is going on?
View 6 RepliesSo, we have a 2005 ford F 250 6.0 diesel and we had the engine changed out from a 2006. Now the truck will not start on hot crank. It will start up normal when cold. So dummy plugs and stand pipes were changed out as well as the oil pump and turbo from the 2005 engine because they were still perfect. What else could be causing the truck not to start up after truck is hot. Does the engine number have anything to do with it? Or anything electrical
View 5 Replies2005 F250 Superduty Crewcab 4x4 6.0L diesel/auto
Wife drove the truck before me and bunched the floor mat under the pedals. I didn't notice the mat issue when I drove the truck today. I accelerated fully after doing a left turn onto a busy highway. The motor spun up hard with the accelerator floored but because of the mats, the pedal stuck all the way down. I was approaching stopped traffic while under full acceleration and I shut the engine off and pulled over to the shoulder all while braking hard ( it was a hell of a ride!). I freed the pedal and restarted the engine.
Now, despite a bit less than 1/2 tank of fuel (I have the 38 gal tank), the dash readout was showing "Low Fuel", the gas gauge was below E and the engine was running like it was running out of fuel. I turned the engine off again and left it off for 1/2 hour before restarting it but the gauge and engine still behaved the same. As I drove to the nearest diesel station, the engine was not running "right". Of course the station I pulled into had 1 diesel pump and the pump was broken.
Because I thought I might actually be out of fuel, an understanding stranger took me to the store to buy some gas cans and then to another station to get 6 gallons of fuel. I got back to the truck and added the 6 gallons of fuel. When I turned the key on, the fuel gauge immediately came up to 1/2 tank. I then drove to that other station and added another 15 gallons of fuel to fill it. This confirmed that I had about 18 gallons of fuel in truck when the "Low fuel" warning occurred.
So, what the heck was going on with the fuel gauge? I am sure the "Low Fuel" warning is tied directly to the gauge but why was the gauge reading low? Is it possible that the "Key-off" while under full acceleration followed by hard braking had confused the ECU? I am just trying to figure out if I have a fuel sender problem or a confused computer that corrected itself. Until this incident, the fuel gauge has never been a problem but the wife messing up the mats has been an issue!
I have a 2005 f250 just hit 180k last week and it has the 6.0 in it, egr deleted, sinister diesel oil cooler, stc livewire tuner with street tune installed, air raid air intake. Wicked wheel 2 in the turbo. Its throwing codes P0606 and P0341. Cam sensor has been replaced and the other code is a mystery to me. Its been randomly shutting off like you turned off the ignition all day today.
When it stalls it takes 3-4 times to get it fire back up. When you first go to start it the pressure gauge reads 0 but once it fires up it says theres pressure. Also some of the days it never stalls and runs like a champ but other days i cant drive more the 10 feet and then it stalls. I have no idea whats going on with this truck and ive put lots of money into it doing customization and stuff like that so I am hoping that its not on its last leg....
I've got a leak that appears to be coming from the secondary fuel filter housing (the one in the engine compartment)... It's not coming from the filter, but from the side, where there are 4 allen bolts that attach a fitting to the side of the housing...Can I change out the gasket for that piece? I've already tightened the bolts, but the leak persists.
View 14 RepliesMy truck would not open door locks for like ten minutes or do anything. then all off sudden it worked again its this twice...
View 9 RepliesMy truck just started to have issues with the gear shift. The gear shift seems very loose now and it is having trouble getting back into the park position. Is this a larger transmission issue, or is possibly a failing part on the actual shift mechanism?
View 3 Replies2005 f350 188000 on the clock had a bearing get loose in the turbo . Installed a new power-max but if the bearings are oil fed should i also change it? There are no signs of metal in the oil or the old turbo . The oil has 600 miles on it with archoil.
View 1 RepliesShould the upper fuel bowl be empty after sitting for 30 minutes?
I believe no. Which would indicate to me a stuck open injector which Iv been suspected of. Iv been trying to track down a miss that I have and Iv been suspicious of a bad injector but ain't been able to pinpoint which one yet.
I have a 04 late model F250. I have done the EGR delete, oil cooler upgrade, and blue spring upgrade. I have a SCT tuner but truck is currently set to stock.
My issue is it starts fine runs good but dies after about 2 minutes. No stutter or stumble. It acts as if some one just turns the key off. I have to let it sit for about 2 minutes and then it will restart. If I try any sooner then it just cranks but will not fire. This started about three weeks ago. At that time I would be driving and it would just die. I could slip into neutral turn key and it would fire right back up and I could continue down the road. As time has gone by the issue has reoccurred more often and now I have to let it sit for about 2 minutes to get it to start again but then as stated only runs for about 2 minutes and then dies again.
I have a scangauge and here are the readings I can get.
FICM main power is 47.5 - 48 volts at all times = good
FICM Logic power is 10.5 - 11.5 volts at all times = ???
IPR is 33% at idle = good Scangauge does not react fast enough to get info at startup.
ICP voltage KOEO 0.25 volts
Start 1.33 volts
Idle 1.11 - 1.13 volts dips briefly to 0.96 volts
ICP pressure Start 900+
Idle 830ish
Sync between CAMshaft and Crankshaft is 1 = good
Have not gotten fitting to do fuel pressure test yet.
Experienced a weird transmission issue this weekend. Started truck up first thing in the morning, only a short warm up, it was about 50*F. Drove about 200 yards to the gate. Stopped with foot on brake while wife got out to open gate.
Felt truck lunge/surge a little. Thought that was weird. Then it did at again, but more like a double surge, jumping in and out of gear.
Rolled forward through gate then stopped again with foot on brake. It did it again. But this time I noticed the gear indicator in the dash jump. It was shifting from 1st, to 5th, down to 3rd, then back to 1st.
I pulled out my phone and was able to catch video of it doing it a few more times. Start about 16 seconds into video. Transmission Ghosts?
About 1:20 in I drive forward and it shifts to 2nd fine. I stop again at 2:00 in.... and it does it again around 2:30. Then it also flashed a "Check brake system" and "Service AdvanceTrac" message for half a second (around 2:44 in video).
After catching video, I drove the remaining 1/2 mile driveway to the county road and stopped again. It didn't do it any more. It did however flash a traction control off/on message for about half a second. Didn't catch that on video though.
Drove 12 miles to town to Ford dealer. Service Dept was closed (Saturday). It didn't do the shifting again for the rest of the weekend. Made the drive home Monday (140 miles) without a problem.
Dropping it off tomorrow morning at 7AM so they can try to fix it. They hope it stored some codes even though it never gave me a wrench light or other trouble light that stayed on. Hopefully it's a just a software glitch or a faulty sensor.
2003 with 2005 motor, auto trans. After truck is warmed up and been driven a while I get a vibration/nice when stopped. Sometimes the Vibration changes with the brake peddle application. Is there a ps hose that can go bad internally on these? Anything else to look for. It's easy to hear/feel in the cab but can't hear it under the hood. Changed the ps fluid with no change.
View 14 RepliesPurchased 2011 3 weeks ago. Due to not paying attention, put gas in diesel. Had tank dropped and drained but after reassembly, fuel gauge inop. When turn ignition switch on, get normal sweep of all dash gauges but fuel gauge does not read. 2nd tech says sender okay, must be gauge. Dealer ssays if it sweeps, it isn't the gauge. 011 F250 6.7L.....
View 7 RepliesWhen I installed the blue spring kit I noticed that my fuel pressure would stay around 60-61 PSI. Since this was safe I changed my gauge info to display FICM. Anyway I decided I better go back and check on the Fuel PSI since it has been awhile since I checked. I started noticing that when I start my truck up in the morning my fuel pressure usually stays around 60-61 PSI. After it warms up sometimes it will hover around 55 PSI. Other times it will be back at the 60 PSI mark. Not sure if this is regular or not since I haven't been keeping long term track of what is going on. Truck runs great though, just wondering if maybe the fuel pump is getting weak. Also I have my sensor attached to the test port on the fuel bowl.
View 1 RepliesI was driving to a job this morning with my truck loaded with tile for a job and it just died.
It has power to the lights, radio, etc. But when I try to start it it does not even crank and it has no fuel pressure on the gauge and the pump is no running.
It is as if the truck has no power. When it died is was like I turned the key off and it just stopped.