Ford 6.0L Power Stroke Diesel :: Vibration / Noise When Stopped After Truck Warmed Up And Been Driven A While
May 28, 2015
2003 with 2005 motor, auto trans. After truck is warmed up and been driven a while I get a vibration/nice when stopped. Sometimes the Vibration changes with the brake peddle application. Is there a ps hose that can go bad internally on these? Anything else to look for. It's easy to hear/feel in the cab but can't hear it under the hood. Changed the ps fluid with no change.
View 14 Replies
Advertisement
I replaced the all 6 tires and all 3 rear u joints on my 03 dually and steering all feels tight but I still get a vibration above 60.
View 14 Replies
Experienced a weird transmission issue this weekend. Started truck up first thing in the morning, only a short warm up, it was about 50*F. Drove about 200 yards to the gate. Stopped with foot on brake while wife got out to open gate.
Felt truck lunge/surge a little. Thought that was weird. Then it did at again, but more like a double surge, jumping in and out of gear.
Rolled forward through gate then stopped again with foot on brake. It did it again. But this time I noticed the gear indicator in the dash jump. It was shifting from 1st, to 5th, down to 3rd, then back to 1st.
I pulled out my phone and was able to catch video of it doing it a few more times. Start about 16 seconds into video. Transmission Ghosts?
About 1:20 in I drive forward and it shifts to 2nd fine. I stop again at 2:00 in.... and it does it again around 2:30. Then it also flashed a "Check brake system" and "Service AdvanceTrac" message for half a second (around 2:44 in video).
After catching video, I drove the remaining 1/2 mile driveway to the county road and stopped again. It didn't do it any more. It did however flash a traction control off/on message for about half a second. Didn't catch that on video though.
Drove 12 miles to town to Ford dealer. Service Dept was closed (Saturday). It didn't do the shifting again for the rest of the weekend. Made the drive home Monday (140 miles) without a problem.
Dropping it off tomorrow morning at 7AM so they can try to fix it. They hope it stored some codes even though it never gave me a wrench light or other trouble light that stayed on. Hopefully it's a just a software glitch or a faulty sensor.
View 14 Replies
I have a 2005 f250 6.0 diesel. I have changed the 2 fuel filters, fuel pump, sending unit (was broke off in tank )and installed the blue spring fuel pressure regulator kit. My truck will run for a few minutes loose fuel and kill. Could this be a sensor or computer problem
View 12 Replies
I ran about 500 miles today loaded up pretty good and noticed every bump I hit that was enough to rock the truck and trailer that there was a noise I've never heard before. It was like the difference between asphalt and concrete road surfaces, but was only present when the springs were sufficiently compressed. Temps were between -10 when I left to 10 or so above when I was destinated. Would that cause the noise?
View 3 Replies
I have a 2007 Ford F-250 6.0L that's making a vibration noise when I come to a stoplight with my foot on the brake, just idling. I just recently replaced the front brake pads this past weekend. I looked under the hood and visually checked for any obvious things that could be making the noise and did not find any, I did notice my power steering pump is damp with fluid. Now this noise only occurs when my foot is on the brake, anytime my foot is off the brake, it goes away.
I checked brake fluid level and power steering pump fluid level, both are fine except power steering fluid looks like chocolate milk. I don't know if the power steering pump would be the cause of this, but I'm going to replace it because it's leaking and I'm guessing the fluid for the power steering is way overdue. I've only owned this truck since March of this year and it has 128,000 miles on it. Hopefully this video link to youtube works, the sound in the video is the same noise that I'm hearing from the truck. Where this noise is coming from.
Vibration noise powerstroke - YouTube....
View 14 Replies
In the morning, she starts great. Right up. And that's the least time she'll start until tomorrow's morning. Once in a while I'll turn the key and nothing happens, all of my lights are on like normal, but once I turn the key to start, absolutely nothing happens. Next morning, started right up. I can't leave her running everywhere I go. This is my first diesel, I just bought her with 265k miles, looks like she was well taken care of. But she doesn't like to start since the day after I bought her. New alternator because Ford told me, battery light doesn't come on, she still won't start once warm.
View 14 Replies
I have an '03 that misfires. The FICM was replaced around a year ago. FICM volts are at a steady 48. I recently change oil and used a Ford oil filter and cap with new o-ring. I also had the starter changed recently. It now spins over so fast, it reminds me of a gas engine without spark plugs! It starts up every time with no trouble, has plenty of acceleration, and seems to run great, except for the misfiring. It seems to misfire worse when warmed up.
I added some good diesel additive to the fuel, hoping that may work, but it did not. I've been doing some reading in different places and am thinking of disconnecting the ICP sensor and see if it works. I also am considering trying some RevX, or similar stiction additive, but from what I've read, stiction is a cold start and chugging problem, of which I have neither. I have a ScanGuageII with many of the X gauges programmed in, but I am not quite sure what direction I should go.
View 3 Replies
I have 2005 Ford 6.0 turbo diesel. I replaced high pressure oil pump because it would die once it warmed up. Also replaced high pressure fuel rails and icp solenoid. Engine still dies when ect reaches 204 and eot reaches 235. Why it still dies?
View 3 Replies
I have an 04 ford 6.0. It is an 03 model. It has 165xxx miles. It fires right up cold but, once warmed up it will crank but not even try to start. A little starting fluid and it will fire right up. I sent the FICM in and had it tested and it is good. I put in new 850CCA batteries and a 185 amp alternator so my voltage is good. I changed the fuel filter and the oil/oil filter, synthetic 5w-30. It isn't throwing any codes. I am really hoping it's not the HPOP but, think it's probably that or related to it.
View 14 Replies
Truck is running bad when first cranked in the morning, is bucking and running rough until warmed up, think the oil needs to be changed and which additive is better the archoil or Rev x?
View 14 Replies
One of the many things that impresses me about the 6.7 is how well it lugs...... it'll run right down to near 1,000 rpm in 6th gear and stay there till it absolutely has to shift. Like a diesel should. Well, recently, and now more frequently my truck is making some strange noises when it lugs down. It'll mainly do it if I'm towing light, like my flat trailer empty, or maybe if I have a decent load in the bed. But occasionally it'll do it empty. As soon as it lugs down low to 1,000-1,200 and pulls there for a few seconds you'll hear a couple squeaks, then a kinda chugchugchugchug noise. It immediately quits if you let off or make it shift down. It sounds like a turbo-related noise, but I don't really know. Truck only has 9k miles on it. I just know this is one of those things I'll take it back to the dealer and they'll give me the ol "we can't duplicate the problem here." What it could be?
View 8 Replies
I have a 2006 F350 6.0L. That is Having trouble starting after it is warmed up. Ive been told multiple things it could be but the one ive been told the most is the Stand pipe or dummy plug in the oil rail having a small leak. Is this correct? Or is there something else i need to Check??
View 8 Replies
Since day one my 2016 F250 occasionally has a reed sounding vibration at highways speeds near the passenger side occupant handle on the windshield pillar. Talked to a service advisor at the dealer about it, what it could be, so this must not be a common problem . The issue is intermittent and can not be reproduced on demand. I tried blowing compressed air all around the area of the Windshield to see if I could reproduce the sound in a shop setting, but no luck. Only thing in common with this noise is 75+ MPH during a rather windy day. I'm a little reluctant to drop it off at the dealer since intermittent problems are hard to diagnose.
YouTube...
View 10 Replies
I just got a 5 inch turbo back Magnaflow stainless exhaust system installed on my 2007 F 450. The downpipe rests directly on the firewall and causes a horrible vibration and noise at times. I have been on the phone talking directly with Magnaflow trying to resolve this issue
View 6 Replies
Was driving back home from shopping tonight and my truck was making a lot of noise when I tried to accelerate. I noticed the boost gauge on the dash was stuck at 35psi but the MiniMaxx showed 0psi.
No engine light so I babied it home which was about 30mins driving and managed to accelerate slowly to avoid the engine rattling. I didn't want to shut it down and restart in case it wouldn't start again for some reason.
When I got home I idled until EGT was <300F like I normally do (it never went over 700F when I was driving home) and then restarted it. The gauges worked fine, MiniMax showed boost and the engine revved freely with no rattling noise. I haven't taken it out for a road test, I'll do that when it's daylight.
Bad sensor somewhere? I would think if the turbo had failed it wouldn't have been fine after a restart.
View 5 Replies
Newbie hear to the 6.0L's. But I'm learning an awful lot really quick from all of you here. I've read lots of tech stuff on these EGR Coolers, oil coolers, FICM tests. This is what I got happening right now.
2004 F-250 6.0L. Today was 45 degrees in Reno. 5400 ft elevation. Tried to start it without block heater. Would not even crank. It tried to crank but sounded like it locked up on first crank. Tried again, nothing. Same. Tried yet again and finally got to getting the engine to crank, but wouldn't start after about 5 seconds of cranking. Waited a little while not wanting to burn out my FICM, then tried again. Same as previous, would crank but not turnover. Checked batteries. Both were over 12.3 V cold, motor not running. This next time, turned key on and let it sit in ON position for about a minute. Then cranked and it took about 5 seconds and then the motor finally cranked over. Lots of black smoke as usual for a cold start like this. Battery volts after cranking over and running were now both over 13.6 V.
Keep in mind the truck has started better than this before in 15 degree weather just about a month ago.
After it started I noticed what appeared to be oil/coolant residue directly underneath trucks transmission area. It was not tranny, but in that area. I got under the truck and can see this fluid coming from EGR Cooler area.
Now for the smoke. Just stared smoking on start up. White smoke. Then it would disappear as engine warmed up. Now its constant white smoke when warmed up and applying the throttle. Smells like coolant coming out of exhaust. Not diesel.
I parked truck facing downwards on my driveway. Then I checked EGR Valve. When I pulled it it was WET. Not dry. Peeked in EGR Valve hole, didn't see coolant. Just wetness. I did change gasket and rings on it the day before as well.
As for FICM, it reads 47.9 Volts on key turn, 48.1 on cranking and 47.8 running. FICM good by all standard 6.0L literature. Degas bottle passed pressure test holding near 15 PSI for 20 minutes! No oil in degas bottle that I can see.
Truck is stock. Is my egr cooler and oil cooler shot? Would a bad egr cooler or oil cooler cause this awful cold start? When I plug in the block heater, it starts NO PROBLEM, but still white smoke. Also, NO loss of power at any time.
View 6 Replies
Wtf is going on, Temps are all good, no check engine codes...bad diesel fuel? I had 1/4 tank of diesel fuel when I filled it up...
View 14 Replies
I have the LED mod and several weeks ago, my LED stopped indicating and the truck would not start in cold weather unless I jumped the terminal on the relay. I replaced the relay and while I was tightening one of the small lugs, the one towards the nose of the truck, I felt it break.
The truck acted just like it had been for the weeks prior, if I didn't jump the relay, it wouldn't cold start, so I assumed, because I had broken that small lug, it wasn't getting the signal to turn them on.
So what now? obviously the GP's themselves are working, as the truck starts when I jump them. But for some reason no signal is getting to the relay. What do I need to check to see what is going on between the PCM and the relay?
View 14 Replies
So loss power on take off and then stopped at store quick shut it down. Came out of store ten minutes later no start just turns over and over. I replaced IPR last year the one on passenger side near frame if that's correct and perhaps this is the ICP near back of engine?
View 14 Replies
I have searched and the only thing close is bad sensor for water in fuel light but it does not say they lost power. When driving or leaving from a stopped position, if I put any extra load on engine by pressing on accelerator pedal fast the water in fuel light comes on and the glow plug light comes on and the truck loses all power. Not 12V power just engine power. I have to let off the pedal and the lights go out and I have power again. Until I press the pedal hard again and it does it again. I have drained the filters and replaced them and still the same.
View 14 Replies
