Ford 6.0L Power Stroke Diesel :: Engine Codes Coming Up After Replacing O-Rings And Copper Washer On Injectors
Nov 18, 2015
I removed the 4 injectors on the drivers side of my 2006 6.0 to clean them up and replace the o-rings and copper compression washer. When I put it all together (everything torqued per shop manual) I am now getting P0266,P0291, and P1000 codes. I have checked the connection on the #2 injector, it is good, and I didn't have any problems with connectors breaking or going back together on the FICM...
The truck will start after a long crank,but smokes and runs rough. It was running without codes before I messed with it. The reason for tearing into It was it has experiencing a pretty big drop in fuel milage. I had been running revx and fuel additives with mixed results...
View 14 Replies
Advertisement
My 1999 F-350 7.3 is leaking from the turbo pedestool o-rings, from what my mechanic tells me. I would like to do this myself as it does not seem overly hard. This is my first diesel truck and am not quit sure how to do it. Looking for instructions or pointers on the process? I am a decent mechanic, but just have no clue on diesel engines and hoping to learn.
View 7 Replies
I just bought a 99 F350 with 240k miles on it and got it for a deal because it needed injectors. Ive done the same job to my 97 OBS powerstroke. The injectors were already pulled so I had them sent for rebuild, the problem is I cant tell which injector goes where. is there a trick to figuring out where each injector goes when I put it back together?
View 4 Replies
How my rings burnt up on one cylinder causing damage to my cylinder wall. My question is this. What could have caused this? I pulled the motor and tore it down. Cylinder wall is chewed up a bit so I was going to have the machine shop sleeve it. Is there another component that I should look at while it's apart? Also the corresponding freeze plug on the same cylinder was showing signs of leaking. I'm thinking that is related to the extreme heat that cylinder experienced.
View 12 Replies
I just finished installing a new set of injectors, standpipes and the blue spring kit on our 2005 Excursion 6.0. The truck idles and runs much better but now it takes almost two seconds of cranking to start the engine. Cold and hot are the same and the length of time between shut down and start doesn't seem to matter either.
What to check? I am planning to check the ICP tonight when I get home. Could I have air trapped some where in the system? This is my first powerstroke so I don't know if this is a possibility.
View 8 Replies
So bummed. I love Ford but this has put a bad taste in my mouth. Glow Plug dropped and destroyed the engine and injectors. Now i have a bill for 15k for a long block and injectors.
View 14 Replies
I have replaced all the injector seals as well as the ball cup seals but when I crank the truck over after a few cranks I see oil bubbling up from the top of all the injectors. When looking at the injectors from the "top" side all looks well but when I use an inspection cam from down below I can see this happening. Any thoughts?
View 9 Replies
I found some 04 injectors for a good price, will the work on my 06?
View 9 Replies
What causes oil coming out of the oil spouts on the injectors? I pulled my VC to re torque my injectors down and I noticed 2 of mine are now leaking oil out the spouts(when warming the engine). Note I did not say the base of the injector.
View 8 Replies
My Excursion got 4 new injectors a couple weeks ago and when I got it back, it was running rough. My mechanic told me it was going to take about 100 miles for them to break in.
300 miles later and it is still running rough. So I opened the hood, took a look around and saw this wiring harness unplugged. Where it goes? Youtube video shows where the harness is [URL] ......
Also, my truck has been shaking violently at 50 miles per hour, unless I hit tow haul, then it is moved up to 60... I am assuming its connected some how to that wiring harness being disconnected.
View 14 Replies
I have a 06 f250 king ranch with 6.0 . A few days ago my scangauge showed a code P0405
I changed my egr and after it showed two codes : P0405 and P0404
It still has a hesitation and loss of power , although better than before the Change.
View 3 Replies
I have 1 bad injector well it's missing when it's cold and two others that are "weak" I'm wondering what kind of job it would be to do by myself?
View 14 Replies
2003 F250 6.0. We had our truck completely checked over by a diesel shop, and we spent $ in repairs on our 6.0 in June having a new high pressure oil injection pump put in, 1 new injector, new oil cooler, new EGR cooler, FCIM and a few other odds and ends. We had this done before leaving Michigan to spend 6 months on the road for my husband's job while pulling our 5th wheel. We were on the road for 6 hours, got to the middle of Pennsylvania, and every injector blows out of the engine all at once. One head is cracked, all injectors are burned, brand new oil pressure pump is destroyed, oil is pouring out of the turbo. The mechanic we were towed to says we got bad fuel that caused catastrophic failure and he proceeds to rebuild our engine. 2 injectors were so badly destroyed that they could not be rebuilt. We had the fuel tested by a lab and the lab says the fuel is fine. What would cause such a catastrophic failure like this?
View 14 Replies
I have a bit of a quandary with my 6.0 and I'm wondering how it compares to others. If you have a hot or race tune (example: super panty dropper) on your 6.0 with stock injectors, what is the peak high pressure oil that you see at full throttle?
Need to know high pressure oil PSI @ full throttle, year (or better yet which style hpop you have if you know), if your ecu tune is a "race" tune, and if you have any FICM tuning.
View 7 Replies
I have a 2003 Excursion with the 6.0 power stroke. I recently had a few codes, cylinder 2, 3, and 8 contribution/balance fault. I asked a buddy of mine, and he said I needed new injectors. I replaced them all, properly torqued everything down, and got it running. She ran for 20 minutes before it started missing again. I shut it down, and since then it hasn't started. That was two Sundays ago. Since then, I've replaced the ficm, all fuses related to the ficm and fuel pump, and even went in and checked all the connectors. Everything is in place, but it still won't run.
View 14 Replies
2004 F250 6.0 and it's a no start. I have a snap on scanner and I did koeo test and it came up as inj circuit low for all 8 inj. I performed "the buzz test " and all inj click. The voltage on the scanner for the ficm is 52 and everything I read say that's more that enough. Where I should look?
View 1 Replies
Powerstroke 6.0 no crank no start... 2004 Excursion. I cannot get any of scanners to connect to get any codes. I have the Autoenginuity Ford Package, scanguage II and another generic scanner. There is power to the diagnostic connector but there is no communication.
I have recently been having issues with rough running cold starts. Codes before this no crank event were 2285 ICP Sensor Low and 0528 fan speed sensor low and one for EGR which has been deleted. Just last weekend I had crank no start. I unplugged the ICP sensor and started and ran. I ordered a new OEM ICP sensor and pigtail and the truck sat until I received them.
Recent Work : I just replaced the ICP sensor and the pig tail. I soldered and heat shrank the wires rather than using the quick connects. I did find that after soldering the pigtail I found two wires shorted on the pigtail. Per the diagram on the 6.0 bible the a/b wires were shorted. I have corrected those. I also noticed that the top of the glow plug control connector has a broken clip. Not sure if there is a connection issue so I have tried to ensure that it is pushed in as far as it will go. I have another module somewhere I'll have to see if I can find it. Replaced glow plugs and harness about 6 months ago.
What have I done:
- Pulled access panel on FICM has 4 posts.
- FICM voltage 48v Key On.
- FICM voltage 46v cranking
Check the diagnostic connector can +/- (pins 6/14) and has resistance 122.1
I've check all the fuses and specifically:
#20 FICM
#22 Engine Control
I found one bad fuse #115 Trailer Tow Charge.
When trying to start Glow Plug light comes on but doesn't go out. The injectors are not initializing and the fuel pump doesn't seem to be running either. I have unplugged sensors ICP, EBP and FSS. Not sure what to test next. I'm considering pulling the ficm harness tomorrow to look for chaffing.
View 14 Replies
Like the title says I'm having an issue the past few days where I can't drive this truck more than a few miles before it starts acting up with rough idle at stoplights/sign and sluggish acceleration until it gets over 1200+rpm.
Cold starts fine, drives good till engine warms up to around 130+ECT then it starts acting up. Stumbles on acceleration for little bit and puts out a little black smoke until it gets moving. No check engine light or codes found.
However a month ago I had the check engine light come on with a P0404 & P0405 and it still started & ran/drove great even towing. If I reset the code it would stay off until I restarted the engine the next time. I replaced the Dorman EGR because it had a lifetime warranty and only had 5,000 miles on the first one. The code did not go away until about two weeks ago the light went off on the dash and has never come back but I had not erased the code? So I'm not sure if this is still lingering issue or what.
I was checking my ScangaugeII when I came back home today while the engine was still idling rough and this what I saw for Numbers:
Low idle in Park
ECT 193
EOT 191
FICM 49.0
IPR 21.4
ICP 582
ICV 0.81
V 13.8
TFC 1.91
VSS(fan speed) 0
(This one doesn't seem right in the past is 500 or more rpm from what I remember?) What am I missing to check over?
View 7 Replies
I have been having trouble w my 04 I checked all fuses all relays all dash lights work, no buzzing on injectors when key turned on. I checked push pull plug for starter it turns over with direct to battery but still does not start. New computer on fender.
View 2 Replies
I have a 2016 F350 disel with 2500 miles. It's at the dealer now they are telling me some metal shavings clogged one of the injectors. What should I be looking for?
View 14 Replies
I think my starter took a s hit like I said truck randomly doesn't crank all lights on dash come on can hear injectors buzzing turn key nothing. Took wire off passenger's side of truck yellow wire touched to pos post solenoid click no crank. So I had the old lady sit in the drivers seat well I hit the starter with my BMFH started right up could something else cause this or should I just bite the bullet and replace the starter?
View 7 Replies
