Ford 6.0L Power Stroke Diesel :: Engine Off Scan Gauge Shows 14.4lbs
Jul 4, 2017
2005 f350 6.0, parked in my shop and the batteries were dead after 2 weeks on vacation, (I left a few items plugged into 12vdc ports charging) charged it up and started right up. Next day cruising down the road about 75 the wrench icon showed up, strange. I reviewed my scan gauge and only thing not correct was my boost, it was 20lbs plus, idles at 14lbs. dash gauge appears normal.
Next morning I turned on the key, turned on my scan gauge engine is not running and the reading show 14.4lbs on my scan gauge. so..... adding the 14.4 to the scan gauge reading thru the drive cycle. so my computer thinks it is seeing 20-30 boost during acceleration. A bad sensor......... but don't know which one.
View 4 Replies
Advertisement
My ScanGauge just went blank, which was nuisance because I like to monitor it in the mountain climbs. It felt like a 'naked' dash without it. My separate pyrometer was the only additional info I had. The ScanGauge only has a few thousand miles on it. Wondering how reliable these things are before considering getting another, or inquiring about a fix I know I will first have to double check that the OBII port is still OK, but I expect it is.
View 11 Replies
I have googled for this and searched the typical sites but cannot find the PID to monitor the MAF with my scan gauge II. Am I blind or does it even exist?
View 1 Replies
I'm trying to chase down a couple of issues and I need to be able to monitor the coolant (and oil) temps. I've downloaded the manual and the specific 6.0 X Gauge commands but don't see the coolant temps listed.
View 8 Replies
I'm looking to buy a used 2005-2007 6.0L and bought a ScanGauge to take with me when I look at the next truck I'll be considering. I dont have a truck now and I see that the ScanGauge derives power from OBD port of the truck. Is there any other way to set it up in advance?
View 9 Replies
Bought this truck, and the engine coolant temp gauge does not work, so I replaced the sender, still don't work.
View 8 Replies
Noticed the other day when I went to leave a job site my Check Engine Light came on but the truck started fine and seemed to run normal. while cruising down the highway I noticed that my factory boost gauge was showing 35psi and fluctuating between that and around 10. looking at my H&S it was showing normal boost readings for the current driving condition, when I came to a stop the H&S would show 0psi but the factory one would fluctuate between 0 and 35-40psi..
I can tell the turbo is not spooling at all during this time. if I take off from a stop with the gauge showing 35 the engine sounds louder than normal at first take off compared to when the gauge is reading normal. I haven't gotten a change to get it in my shop yet to look it over but does the dash gauge read from a different sensor that what my H&S is reading? Truck is an '11 F250, deleted both EGR and DPF with H&S tuner. I checked codes and all I have is P06A7. Where to start?
View 4 Replies
My 2012 got it's first "500 miles to empty...." DEF alarm yesterday. I added 2.5 gallons and the same alarm keeps showing up each time I start the engine. Is there some kind of other reset required? Do I need to fill the tank up completely to reset it? I'm concerned the engine will shut down after 500 miles even though the DEF tank is about 1/2 full.
View 14 Replies
2005 PSD Ex. 4x4.
Drove it a few nights ago and it felt really gutless. Next morning, no start. Well, it tried, but it sounded like it was run out of fuel (had half a tank)and I turned it off. Changed both fuel filters, key on / key off to purge system about 2 dozen times. Still no start.
I have all eight injectors with "injector Circuit Low" code, a P0401 - Exhaust Gas ReCir Flow Insufficient Detected, and P0672 - Glow Plug #2 (which it has had for a few months).
I thought with all of the injectors, it might be the FICM, checked the FICM voltage with Torque during a start and it showed 47V the whole time.
Harness? I did not think running with the glow plug error would be a big deal especially during the summer in So Cal.
View 9 Replies
2005 6.0L F250 Lariat. I picked up a couple weeks ago. The message center in the gauge cluster will only show my mileage (kilometres) and engine hours but nothing else.
Also the three buttons/controls to the right of the steering column don't do anything. I checked the wiring behind the dash and it's all plugged in... The other problem is the SRS light will flash on and off while driving.
View 2 Replies
Purchased a used 2005 Prius with 30,000 on the clock. Have put 5,000 miles on the car with no problems. Recently the check engine light came on and my Scan Gauge indicated a trouble code of "P0000". Cleared the code and four days and 500 miles later the check engine light returned with the same code. Car runs great even with the light on. Have check the fuel cap which was and is tight.
View 2 Replies
Purchased 2011 3 weeks ago. Due to not paying attention, put gas in diesel. Had tank dropped and drained but after reassembly, fuel gauge inop. When turn ignition switch on, get normal sweep of all dash gauges but fuel gauge does not read. 2nd tech says sender okay, must be gauge. Dealer ssays if it sweeps, it isn't the gauge. 011 F250 6.7L.....
View 7 Replies
Do the gauge cluster out of one super Duty will work in another truck, just plug and play? I have a 2015 550 that the fuel gauge has quit, which is causing the truck to go into limp mode because it will not allow a regen on the DPF. This is a business truck and i need it to be rolling. There appears to be a national back order on gauge clusters from Ford. I have another truck in the fleet that I could do without so I was wondering if I could just swap the clusters would it work?
View 6 Replies
What is the least intrusive way to install an oil pressure gauge in these trucks and still maintain the input to the computer?
View 6 Replies
I currently own a 2006 F550 4x4 pick-up. I just finished changing the oil and my oil pressure gauge is not working....
View 11 Replies
I am installing Torque Pro and Car Gauge Pro on my Yellow Submarine. To keep an eye on things. Well installing it on my tablet, and installing that in my Yellow Sub. I already have the Bluetooth dongle. What to set up, what to monitor, what to test? Etc..... I want to continuously monitor this truck while driving it. Being it went swimming.
View 13 Replies
Have 2006 Ford Power stroke with 6.0 in it.. Just started doing this ... When Im driving the oil pressure gauge is fine and motor sound fine, but sometime when I come to a stop sign the oil gauge will drop all the way down to zero, the motor still runs fine and has plenty of oil in it. After I press on the fuel pedal to raise the RPMS just a couple the gauge goes back up. the odometer will all so blank out and it will flash "read gauges" when this occurs,, its driving me crazy and not sure where to start..
View 14 Replies
My 2005 is doing strange things. The fuel gauge is always incorrect. I have done the following:
1. Replaced fuel level sensor.
2. Inspected and tested wiring from the firewall to the tank.
There are no codes present and the fuel % listed in torque is always correct. The gauge sometimes reads 1/2 above full, nearly all of the time it's above the 3/4 tank mark. I have an android head unit that I am using to gauge fuel level right now. I believe the cluster is bad.
View 9 Replies
I just had headgaskets (oem) studs, egr delete,oil cooler done on my 06 plus water pump cause the gasket blew. I have a sct livewire hooked up monitoring everything and tonight i noticed that the eot and ect's were way off. fully warmed up and rolling 65 Anywhere from 40*-50* out it was eot-156 and ect-172. Degas bottle was at the normal level.
I am also having issues with the fuel gauge. Every now and then the gauge will go to E and the miles to E will display ---. Turn the truck off and back on it works again. I am half assuming its the plug on the sending unit or the sending unit itself.
View 14 Replies
Adding a coolant pressure gauge to truck? There are some expensive kits but considering I already have a gauge that would work, could I just buy a 5v sending unit for fuel pressure or oil pressure and have it work?
View 14 Replies
So the last 3 or 4 times I have filled up my truck the needle on the gas gauge only goes up to about the 3/4 mark. What this could be? And how I could fix it?
View 1 Replies
