2003 F350 6.0 cc 4x4 with 291k... Not sure if I have a problem or not, it happened at a signal light: The light turned green, I pressed the throttle and started to move. As I pressed more, there was no response. Second later it took off and I have had no more problem. What the cause maybe?
View 1 RepliesSo while driving just now the truck went down to idle and no matter what I did to the gas pedal the throttle would not change. The truck didn't die but would just sit at idle. It was like the gas pedal wasn't connected. About a minute later it surged a little and then I was able to drive like normal.
History- last week while at a red light the engine surged and then almost died. Light changed and I hit the gas....and stayed at idle...then died. Restarted and died two more times and then just drove like normal. Changed fuel filters and and checked fuel pressure. Under boost it was 38-40 psi. Idle it was 45. Cac tube replaced due to cracks.
I just recently got my truck back, My father and I switched vehicles due to need and distance's being driven. 2005 F350 6.0, 164,000 miles
I couldn't wait to drive it again, I spent hours detailing and cleaning. Well I go to start and noticed it struggled to start, and didnt seem to be idling right. I looked under the hood and it was leaking fuel from the Regulator. I left it parked and never drove it since he last did. I read around on these forums and I bought the blue spring upgrade kit.
Now I notice it shakes at idle a lot more than it used to, pretty bad at times. Then upon driving it shakes even worse upon acceleration attempts, and has very poor throttle response. I have to put it nearly to the floor and even then the acceleration is nothing like it used to be. Most of my trip was highway at 60mph, and anytime it would start climbing a hill it would shake pretty bad with the acceleration. When i let off the gas to slow down before braking it stopped the shaking.
So I read around on here and I went back and used the factory bowl and valve for the regulator, still had the issue. Next I went back and replaced the blue spring with the original, still have the issue.
I just checked the FICM and it is reading between 48-49 during key on, cycle, and cranking.
Batteries are great
Alternator only reads 13.6 at 2k rpm idle, but have not had charging issues.
My father says he never noticed anything wrong with it other than it occasionally missing out. But I don't see how changing the fuel pressure regulator would have caused this. Especially since I tried every combination of oem and aftermarket parts, ensuring that all the connections and parts were installed correctly.
So I was driving to work and the truck lost throttle response. There was very little of it! Came to a stop then it didn't barely want to move, pulled over then it died on me! No clue what to look at! 2005 6.0 232k miles
View 14 RepliesI just completed installing rebuilt injectors in #2 and #4. for the 2nd time. The first set had failures with those two. After assembly, the engine runs rough which is understandable considering the air introduced. I can run the RPMs up while in neutral or park, however; there is almost no throttle response in drive or reverse. It will barely move and only slightly raises the RPMs. I am unable to drive it to get the air out until this particular issue is solved.
Prior to the tear down for #2 and #4, the throttle response was fine.
Current Codes:
P0272 - I am hoping this would go away once the air is gone.
Software:
AE w/ Ford Bundle (New to me)
Buzz test is fine
Power balance looks great
FICM logic and power are good
Skills:
DIY w/ limited electrical knowledge
Recent Mods in last 300 miles:
New heads
ARP studs
ICP
IPR
FICM w/ Atlas 40 from FICMreapir.com
Injector harness
HPOP
Chemical flushes
Oil Cooler
Leak Proof Ball Tubes
Stand Pipes
8 Rebuilt Injectors
Batteries
MAP Sensor
New Turbo w/ updated supply and return
All associated gaskets and orings replaced with the above
All OEM where available, except injector rebuild service
I've been having rather slow throttle response with my 6.0 f250 diesel at lower RPMs. Obviously, this is to be expected to some point.. Whether I'm cruising on the highway or through the neighborhood, if the truck is at lower RPMs and I try to accelerate, it doesn't want to. In order to get it to accelerate, I have to press the gas down enough to downshift it then it'll take off.
The truck doesn't have a loss of power at higher RPMs, it takes off like a bat out of hell. I've put 175CC injectors in, tuned it, power max turbo, EGR deleted / studded, etc. It's almost go out with acceleration, or go turtle power with acceleration.
Oil pump was replaced a couple years ago. This problem existed through it all, and it's rather annoying. The truck doesn't want to produce any low end power. If I try to hit the gas enough to accelerate but not enough to force a downshift, I'll just blow smoke, spool the turbo, and barely accelerate until I down shift or push the truck through it. Turbo PSI is roughly ~15ish-20ish during the sluggish transition.
2007 F350 6.0L 230,000 miles
Yesterday, while driving home from a weekend out of town trip, all of sudden lost throttle control. Just went to idle while at cruise speeds, could pump pedal and no response. Then got pedal control back and seemed to run normally.
This happened several times. Hubby suggested moving the adjustable pedal which I did slightly. Although I was not using the cruise control, we had a sense that maybe it was engaging??? So I hit the off button a couple of times. After these two interventions, drove the last 80 miles home with no further incidents.
Today, we checked codes and had a PO231, Fuel Pump Secondary Circuit Low. I don't think that is our problem with above based on research, but we will look into fixing that too. We are thinking TPS or a position sensor on the accelerator pedal. We could replace those easily ourselves.
2004 F250 Powerstroke Diesel 6.0L ... 90,xxx miles
Symptoms : Within the past 10,000 miles the truck has begun exhibiting the following problems, sometimes in conjunction with one another and sometimes just independently of one another:Stalling on the road at low speed / low engine RPM.
Throttle pedal becomes completely unresponsive. Stabbing the throttle pedal repeatedly sometimes causes it to return to operation. Sometimes the engine must be shut off and re-started to return throttle pedal to operation.
Rough, surging, stumbling idle at rest. Will crank but not fire occasionally. Problem has become worse as of late. Repeated attempts at starting the engine usually result in success after much, much retrying.
Work Done : Local Ford Diesel technician replaced the EBP sensor, replaced the EGR valve and re-flashed computer with latest software -- all under warranty. Problems still persist.
Peculiarities : We have tried driving the truck with the EGR valve disconnected and with it connected, both at the technician's request.
With the EGR valve disconnected the truck usually starts fine but still stalls out at low RPM / low speed. Fuel economy is also cut by nearly 50% with the EGR valve disconnected. Really couldn't afford to keep driving the truck like this.
Technician speculated that if the truck continued to die with the EGR valve unplugged, it meant that the computer or fuel pump might be bad. ????
It also seems that the stalling problem manifests after the truck has been driven at highway speeds (65-70mph) for at least a period of 20-30 minutes. Stalling usually happens as soon as we make an exit off of the highway and begin to slow down to make exit. As in foot off the throttle pedal. Engine RPM drops then stumbles then stalls.
I wonder if this is a problem with the HPOP or ICP system.
Specifically I wonder if this is a cracked quick release fitting that allows oil pressure to fall after the engine heats up and oil viscosity thins out with the heat. Once the engine cools down sufficiently to thicken the oil, the HPOP finally gets enough oil pressure to allow the engine to fire up again.
I was sitting at a light and when it turned green I hit the gas pedal and had no response engine was idling perfect and a wrench light came on , I then shut off the truck restarted it and light was off hit the gas it came back on and it was intermittent with taking so I replaced the pedal and it is still doing it...
View 7 RepliesGot a 2011 f 250 6.7...turbo started making a sound more like a turbine in a plane when I hit the throttle to cross the street...boost gage went to 0...i got a new turbocharger from garrett. Installed it and when I started the car there was no boost at all. I searched for any leaks and nothing. I get a code p132b.
View 7 RepliesMy 7.3 has no throttle response, the code reader says pass, and there are no codes, would it do this even thow it has a bad TPS?
View 4 Repliesi got a 99 F250 powerstroke with 148K on its clock, i have a couple issues that i cant find a definitive answer for, 1 just started recently, Its an automatic and when it shifts into third around 40 mph the rpms drop to 1200-1300 or so, its done it since i got it, but recently it wont accelerate like it should or used to do, i have to put it down and make it downshift to recover.
Now I have no CEL. and it is still running perfect just has very little power, I do have a 4 inch turbo back exhaust and have a TS 6 position chip with i usually run in +50hp mode, but it does this in all positions. Now issue 2 is when its 30 degrees sometimes it will not start. It'll turn over with now fire. but if i cycle the key again it'll fire right up like a champ? It has a 4 month old starter and batteries and a month old alternator and i have tried several CPS' and Contently check the connections.
I have a 99 F450 with the 7.3L in it. I brought it home the other day and parked it. Later I went to do something with it and I had no throttle response at all. I checked the wiring going in and coming out of the throttle position sensor. I have approx. 5 volts going in and the voltage sits at about .5 volts and rises as the accelerator is depressed on the outgoing wire. The other switch on the pedal is open and does close when the pedal is depressed, so it seems those are fine. I'm not sure what I'm supposed to have on the 3rd wire that goes to the TPS.
I have a Bully Dog tuner and it shows an exhaust back pressure sensor error and a couple of voltage errors to the accelerator pedal. I read somewhere that someone had an exhaust sensor short out and it starved the accelerator pedal from voltage or something like that but I do have good voltage at the pedal going in and out. I ordered a new sensor and tube.
If the exhaust pressure sensor was shorting out and I unhooked the wires could that make the pedal work if the sensor was the problem or would the accelerator pedal not work at all without that sensor being connected? (The old tube was somewhat plugged up and I saw it had a small rust hole in it)
If it's not the sensor, what else can I check? Where can I check under the hood to see if the wires from the TPS are getting power to where they need to? I assume they go to the computer and that tells the pump or whatever to give more fuel.
I own a 2000 F250 7.3 Powerstroke 4x4. The only aftermarket engine modification I have is a Tymar intake. The problem I'm having started about 6 months ago in a very erratic fashion. I would pull up to a traffic signal and as the light changed to green, without warning the truck would have no throttle response. The engine was running fine; there was just no response as I stepped on the accelerator pedal. Usually when I put the transmission in neutral, revved the engine a few times, the throttle would come back on line. This happened 4 or 5 times over the summer and then went away completely until today. Today it came back with a vengeance. At one point I had to shut the engine down completely to restore throttle response. It's a bit unnerving when it happens in the middle of a busy intersection. I was told that it may be the throttle position sensor. Does this sound correct and does it need to be replaced?
View 14 RepliesI have read many different threads regarding the TPS sensor on the pedal and EBPV deletes on the E99 7.3L Powerstrokes. I am trying to troubleshoot some issues with my E99 7.3L. Usually on cool mornings and after not being started for awhile the truck will seem to be stuck in an Idle. This is an intermittent problem that doesn't always happen.
I cleaned the connections to the Tps and the IVS sensor and put them back in. No luck. On another note I am also seeing a reduction in fuel mileage and power like the truck is being restricted. I don't know if these symptoms are related or possibly their own issues. I am troubleshooting and possibly thinking it is the EBPV system that isn't working correctly. Considering doing an EBPV delete with a NON-EBPV Pedestal and Flange.
7.3 2001 model starts ok at 32-35 F. Feels a bit sluggish / slow response on the road. Reach a hill after 3-4 miles. Engine temp then beginning to go above low level mark. 100 meters up the hill, going around 30 mph there is a sudden surge in the throttle although my pedal is steady. Going back a few minutes later, on flat ground at bottom of hill and with no accelerator pressure, the engine suddenly stalls. Starts fine again after I stop. The same history actually repeated on two separate days recdently on the same hill. CPS is recently replaced. Had some jerking before that, but not the behavior explained above. Current CPS is Delphi light grey. Recent fuel filter change and oil change as well
View 14 RepliesI have a 2005 Ford F-250 Powerstroke. At times when stopping at light or for any reason, I give it gas but it does not want to go. It's like it is not even registering that I am pushing the pedal. I shift it into neutral and rev it up then switch it back to drive and it goes and puffs out smoke. What is going on?
View 6 RepliesFriday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
Recently I have encountered another issue. Truck started up fine, at first stop light and truck was bogging down, RPMs jumping up and down slightly and sounded like it was going to die. Light turned green, gave it gas, no response. Gas pedal was dead. After restarting the truck I was able to give it some gas until I came to the next stop light and this repeated. Eventually a few moments later I got a check engine light. Drove home this way, seemed to be working fine as long as I was actually driving and not stopped.
All the parameters looked ok except for the battery, that jumped up and down in volts as the engine sounded like it was bogging down then eventually died. New batteries put in approx 2 months ago. The check engine light is showing "P0299 turbo/supercharger underboost". I have attached an image of this check engine light according to my monitor.
Ever since I've had this truck my parking brake has acted like this. My buddy has an '03 and his acts the same, but I figured I'd ask the question.
9 times out of 10 to set the parking brake, the pedal goes almost to the floor and doesn't seem like it really does anything. The other 1 out of 10 it goes half way and feels like it actually sets. Is this normal?
This is my first winter with my 6.7 and I've noticed that since the weather has been cold the motor rattles a lot more, doesn't seem to want to rev as freely and it seems like the turbo response is slower. I've noticed that my truck goes into exhaust cleaning more frequently, three times in the last week before Christmas. The transmission thumps on downshifts the colder it is. The first shift out of my driveway is between a thump and a bang. The dealer told me I'm not ready for a trans flush, it's not cold enough to need to use the engine heater and that some of the noise and lack of performance could be winter blend fuel.
View 8 Replies