I am having problems with my steering being all over the place. I noticed it at first when braking. It would pull to both sides. At a stop light holding the brakes my steering would randomly pull. I replaced the power steering pump. It didn't fix it. Now just driving it pulls all over. I was thinking steering box?
View 14 RepliesSo when driving my tuck the steering on it would sorta lock up like it wanted to push the truck to one side then it would free up and the steering would be real loose it just felt like it had no power steering to one side it's not the same side each time and it pulses when I'm at a stop if I move the the tires Erving the motor doesn't seem to work so far I have replaced ball joints and all tie rods they needed done anyways it would still do it got an alignment done last week and it almost seems worse now could just be coincidence.
I'm thinking power steering pump but when the steering locks up to one side I'm also wondering if it's the steering box it's kinda hard to explain it what's going on and there is no popping noise or anything when the steering frees up. It's kinda scary on the freeway when I go around a corner the steering gets real loose and wonders back and forth not all the time but quit a bit but when going strait it will feel like it wants to pull to one side then the steering will loosen up again. The steering will wine only first thing in the morning when I pull out of the driveway then it's fine
Initially had indications of a leak under the wheel arch on the drivers side.
About 3-4 months back replaced both PS lines and the leak stopped - briefly (maybe a couple a weeks).
Now the leak is back, but what's interesting is I lose more ATF fluid on a single long haul run than I do running round town for 3 weeks. I can't work out where the leak is coming from to identify what else to replace - short of just buying a pump and reservoir and replacing them as I've already done the hoses.
My turbo cooler pipe was hard up against the old PS pipe where it entered the side of the reservoir until I did the replacement hoses. Now I have it out the way but I'm wondering if it's caused some unseen wear or damage.
If I just do the pump to see if that works are the reman units any good out of Autozone or O'reilly's?
I bought a 99 7.3 been in the trees for a few years pulled it home and now trying to get it running. Did a service new filters and oil fuel too. I can get it to start and will run but runs very rough and if you put it in drive cant pull its own self. I don't have a check eng light on. And found out my scanner is a pos lol. it will hooked up and then try to pull codes and loses it connection. But that's the scanner will not work on my other 7.3 as well.
I am making high pressure oil checked off the rail with gauge and it will build up to 2000 psi when I rev it. but missing like crazy. I swaped the pcm and idm out of my running 7.3 and it didn't change a thing. I have checked the pass though and they are fine. pulled drivers side valve cover off and no oil leaks when running and rockers are fine. new ipr valve as well too. I know I need to get a scanner to talk to this thing better.
Every time I hit a hill, loaded or empty, or get on the truck on level ground after about 15 seconds it acts like it's running out of fuel. The pump starts getting noisy like it has air in it, but it'll straighten out eventually. If you don't let off the fuel it'll eventually stall out. No check engine light, no codes. Truck has a ts chip but it does it on all settings. New fuel filter, changed oil with hot shots secret, new air filter, hutch mod done. I'm at a loss for what to do. Good fuel pressure also.
View 8 RepliesThe truck is a new to me 99 f250 7.3. The problem occurred before doing the brakes, and after. The front brakes had new pads and calipers(rotors appeared to be in good condition) while the rears got New rotors, calipers, pads. The persisting problem is a really bad brake shudder that seems to be getting worse. It only occurs below about 5-10mph when braking. on this trip back to school there is a hill with a stop sign at the bottom where i should have rolled forward when i let my foot off the brake. This didn't happen.
It almost seemed as if the tires(meaty 35in dick cepek crushers) where rubbing and catching on something. but we checked and it didn't seems as if they were, though they do come somewhat close to the bumper. Im not even sure if its brakes or what it is, a friend of mine said possibly the hubs, but what can i do to pinpoint it? I wanna try loading down the front with something to simulate the drop when braking and see if the tires do indeed hit as when going to a rolling stop with only a little braking it doesn't do it. Any other things to check?
2001 F250 7.3 4x4 330000
So weird noise while breaking but only right at the very end of the breaking cycle or if breaking hard. As soon as you come of the breaks it stops. Changed out front rotors and pads last night thinking that was it but its not. I'm inclined to think it could be the driver rear side by having someone else drive and brake whilst stood by it - rear rotors and pads changed 18 months ago and quick visual check appears they are ok. Just can't work it out - any thoughts? Caliper seemed ok on the front left, but would probably need doing in the next 6 months
I have a shaking issue only at 40 mph + only while i am braking. I thought warped rotors, but the pedal isn't pulsing and if they are warped, wouldn't it do it every time regardless of the speed??
My second thought was the center support bearing. It had some movement so I replaced it tonight. Now there isn't any movement in the drive line. After a test drive, it hasn't gone completely away. It is still barely there.
I am not sure where to go next.
The noise is somewhere between a tin rattle and a bearing grinding heard most when braking but constant under say 10 mph. We have not been able to pinpoint where exactly it is coming from but I believe it is front drivers side.(but really could be anywhere) it is not dependent on rpm, nor gear or clutch engagement, Nor hubs engaged or disengaged.
The drives side front hub, rear hubs' bearings(races and seals) have been replaced. I have the passenger side front hub to do as well, just haven't gotten to it yet and it doesn't seem bad. we are all stumped on what it is. It seems to relate to the rotating assembly though as it seems to change with speed. it almost seems like tire rub, but there is no scaring or marks of any sort anywhere for it.
Vehicle is a e99 f250 short bed ext cab. open diff if it makes any difference. My next thought after the hub is pinion bearing? Could it be something to do with abs? say the truck is 4 wheel abs but the fronts are disconnected (trying to figure out if it is 4wabs as it appears to have connectors, but the original hubs did not have the hole for the sensors. no abs light comes on, but that could be a bad bulb too)
What we have found is hubs locked or unlocked, 4wd engaged or disengaged, and happens at right around 16 mph, braking, accelerating, clutch in or out, in gear or in neutral. All 4 corners have new bearings. We have found 2 things, 1 is the track bar bushings are shot (don't think this is the source of the noise but could be wrong and i will be replacing those..once I have money in again.. 2 the passenger side leaf spring when wacked with your hand makes a different sound than the drivers side.( could be a matter of different loads, but figured worth noting)
There are 2 noises, the first is the noise we hear, the second is one that i found when doing the noise reduction (loud meaty tires you cant hear the noise in the audio without reduction) I think that that was one of the hubs, or maybe the brakes, I am unsure, but it happens at different locations in the video.
Audio : [URL] ....
I picked up a 2000 4x4 F250 on Saturday.
The truck rides pretty good but on bumpy roads there is a loose sounding rattle in the front end. Also when applying the brakes there is a thud in the front drives side. You can feel it in the drivers floor board a little. Once you start braking about halfway to complete stop is when the thud is, if that makes sense. I suspect bushings but how do I know which ones.
Can I swap my seat bottoms? I have '99 F350 with 40-20-40 seats. Drivers seat is getting tired. Would like to take just the seat bottom and flip-flop. Can it be done?
View 3 RepliesCan I swap my seat bottoms? I have '99F350 with 40-20-40 seats. Drivers seat is getting tired. Would like to take just the seat bottom and flip-flop. Can it be done?
View 14 RepliesThe problem makes the car unsafe to drive. The quickest way to describe it is a hard pull to the left after a very linear steering feel. My perception is almost as something is holding on and then just fails and lets go and the car quite abruptly shoots left in a very unsafe manner. Here are the things I have done to remedy the situation, I replaced the struts with factory replacements 15,000 miles ago. At the same time i replaced the left and right axles, drove the car with the problem then last weekend, I replaced the upper tie rod arms, and lower tie rod ends, the sway bar bushings, and the control arms on both sides. I literally feel as though it is a darn near new front end.
Just yesterday I had 4 new Goodyear eagle tires and an alignment done and the problem became more pronounced and worst. I really like this car and want it to be a joy to drive as I know from others these little hatchbacks are a real joy on winding mountain roads.
My 7.3 power steering is acting up. Feels like I am up against a rock. At slow speeds like parking lot maneuvering I struggle to turn wheel. Then all of a sudden I'll get power steering back and wheel will rapidly turn. Freaky.
Brake pressure is fine. They shutter pretty bad even with the new rotors I just put on but they have good pressure. But the steering is intermittent or no power steer.
I saw online to run engine at 2000 rpm and try steering but no change. Still no power steer. There is fluid in reservoir. There is fluid seeping up steering column from steering box. No clue if this is related or unrelated.
How to troubleshoot further. I hate throwing parts at problems before truly diagnosing. Also have pretty aggressive lurching during turns in four wheel drive. It's present on dirt road but worse on pavement. Don't know if this is related or not.
So, I'm replacing the Steering Box today and read an article that said you should replace the pump at the same time. what do you all think?? I have clear access to it now and they are not all that expensive?? Or are the ford one's bullet proof and leave it alone???
I don't have any leaks and it feels ok I guess..just pushing close to 200K on it.
I've got an 01 7.3 lariat 4x4 with an 03 7.3 engine in it (long story behind that) but basically I noticed one day I had a hissing underneath my dash and my brake pedal was a little spongy but my truck stopped, well before I could get it to a shop and checked out it went bad. Coming up to a stop sign and as normal hit my brakes and right before it came to a complete stop the pedal shot to the floor and I lost power steering as well as brakes and went rolling out in the road and almost got hit. So it's been parked ever since and I have changed the hydroboost, the power steering pump twice, flushed everything and bled everything and still nothing, can't even find any leaks. What to even replace now or whether to just take it to a shop and spend another small fortune.
View 7 RepliesI have been noticing my brake pedal is very firm on and off also my power steering seems to get harder to turn than other times. But today i was sitting at a few lights and could hear my power steering pump growling at me intermittently if you want to call it that.
Also sometimes my truck will pull to the left or right then it goes away if i hit the brakes again. I don't see how the hydra-boost system would do something like that. But its not the slide pins because i just greased those along with new brakes and rotors all around at the beginning of winter.
I noticed when I grabbed my fluid lines going to the hydra boost from the power steering pump they seemed to rattle very rough so that makes me wonder if the pump isn't going out. How are the brakes supposed to be on these trucks? nice and soft? rock hard?
By the way truck is an 02 with 144k on it
I have a 2000 Excursion. This weekend, I noticed some intermittent failure of the power steering where it seemed like the pump was not engaging and then would all of the sudden. Deciding to try to head off a failure, I got a reman unit from Oreilly and installed it this morning. It was fine when I tested, had good brakes and went locked to lock quietly without fuss. Let the house and within a mile, I lost steering and brake assist. I stopped and turned around, but what I am noticing is that at idle, I have no power steering, but when the RPM's are up, I do.
View 3 RepliesMy power steering is only working when i turn it to the left. When I turn it to the right i have to get a 1/4 of a turn in until the power steering takes over. So i get under my truck to discover what seems to be a piece of my tranny missing. How screwed am I ???
View 11 RepliesMy high pressure power steering hose just blew at the "B" nut at the pump. Meaning, the fitting is still in the pump but the line is out. Do I need to replace the whole line or is there a retainer I can swap out?
View 14 RepliesEver since i bought my truck i have had a bad power steering whine. Replaced the pump and its still there. I got the truck in 2006 and think i replaced the pump in 08 maybe. Anyway I've purged, bleed, changed the fluid. Pulled a vacuum on it and still no luck. So I've just dealt with it for 11 years.
Well i can remember reading something somewhere about ford up-dating or redesigning one of the power steering lines that was causing this noise.
My father inlaw just bought a 02 and its so pleasant not to hear that when riding in his truck. It made me want to investigate the matter. SO if its as simple as a updated line I'm buying one asap. He got rid of his Chevy because of the reliability I've gotten out of mine.