Ford Brakes/Suspension :: ABS System Failed - Module Replacement?
Jun 28, 2016
I took my 2009 F150 XLT 4.6 into the dealership to have front and rear brakes replaced at 77,000 miles. Brakes were down to 3mm. They also did a complete brake flush. They called after the brake job was done and said the ABS system failed and needed to replace ABS module. Given I didn't have any problems with ABS before bringing it into the dealership, what is the chance the brake repair screwed up something with the ABS that they caused?
View 5 Replies
Advertisement
Im wanting to delete my abs brake system in my f150 2002 2wd all disc brakes.
I have to change the module with some kinda valve? and turn off the Abs in a tune?
I know the basics of a brake system, but im lost in the abs stuff.
View 6 Replies
My car is a 1999 Honda Civic.
This morning I went in for a state inspection, oil change and rear brake replacement. Driving home while going downhill on the highway, I hit the brakes - and they failed completely. At first it felt like the car actually bucked forward. I tried flooring the brake, but felt no resistance and the car didn't stop. I kept my foot off the gas and coasted to a stop.
The tow truck driver told me he could feel a problem just getting the car onto the tow truck, and again when he took it off.
The Honda place checked it and did a test drive, found nothing.They said it couldn't be air in the brakes be took me for a short test drive and assured me I'd be fine. The
I headed home again and the brakes failed again at almost the same spot. This time it wasn't a complete failure. After no resistance at first, the brakes "caught" though somewhat mushily. I put on my flashers and kept going, at about 45 mph. Got off the highway and had to crawl because braking wasn't taking effect immediately. But as I drove on at 10 mph, they began working again. Not as well as they should, but enough to get me home.
It seems the brakes fail after 15 - 20 minutes of driving at 65 mph. They work better after a rest and at slower speeds.
If it makes a difference, my compressor is gone, so the car doesn't have a/c, and it is hot out so I'm wondering if the heat is affecting something. However, I haven't had these brake problems until today.
View 19 Replies
Looking to replace the steering stabilizer on my 2008 F-250. It has a 6" lift and 37" tires.
Also, does "dual" mean better?
View 3 Replies
I'm trying to replace the front brake rotors on a 97 Ford Explorer (AWD, 5.0 L). I've removed the calipers and pads - but can not loosen the old rotors. It looks held on by rust - but do I need a special rotor pulling tool?
View 8 Replies
I was wondering if there was how to on doing the MC replacement? The brake pedal goes to the floor almost every time you press on the brake?
View 1 Replies
My van is spouting SRS fault codes 1-3 and 5-1. I had my shop run a diagnosis and it appears the module has failed. I'm having trouble tracking down a replacement. The Module on my van is Ford# F5AF-14BO56-AA. I see modules with -AD or -BD, but none that match this number perfectly. I also see lots of modules for related Ford vehicles from the same era. Looking for a ford parts number reference sheet that will indicate on what vehicles this module was used or if there is any chance that related modules are compatible?
View 14 Replies
I have a '79 F150 4wd and was wondering what would indicate a caliper needing replacement. I'm already going to replace everything on my rear brakes, they are completely trashed. However, the fronts seem OK, NO indications of leaks or seizing both sides of the rotors appear to be evenly "used" I guess. The inner pads do seem to be thicker than the outer pads is this normal? Anything I should be specifically looking for before I have the rotors turned and put a new set of pads on?
View 5 Replies
I replaced the master cylinder 2 months ago and now every now and then the rear lock up for a second. its only happened a couple of times. Pulled the wheels and everything is in place with nominal wear with clean drums and rotors. Am at a loss as to why this is happening.
View 1 Replies
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
View 1 Replies
I have a 2004 VW Phaeton.
Today, the sound system failed, then shortly after, the navigation system failed.
On the console, if I press any map/navigation buttons, the error message "Navigation System Unavailable" is displayed.
If I press an audio related button, the error message "DSP system is unavailable". I took it to a private vw repair shop and a vw dealer. What was causing the issue.
I am now headed to a vw dealer with certified phaeton tech. I looked towards fuse issue, but they appear to be ok..
View 10 Replies
Friday morning my brakes went out on me. I was pulling out of a parking space and my car was puttering (as if it was going to turn off) then I was pulling out of the parking lot, but when I stepped on the brake pedal, it wouldn't go down! So i put it in reverse ( i was going about 5mph)and circled around and just put in park and turned it off. I didn't even think to use the Ebrake. My son was in the back seat so I just tried to stop it automatically.I've been reading that doing that might have ruined my transmission.
It's a 2001 ford focus SE....
View 5 Replies
Bit of sticky problem - it looks like the air suspension system has failed on my 2004 T-Reg. The back-end is dragging - down to aprox 1 foot off pavement and there is no air in the compressor bottle. The problem is that the next dealer is about 75 miles and bit of a ferry ride away. The ride is bouncy and harsh - but otherwise stable.
View 6 Replies
My question is what could cause a wheel bearing and CV joint to fail immediately after a clutch replacement and a general inspection?So I brought my 2014 focus with under 50000 miles in due to the normal transmission issues with clutch chatter and hesitation. Also asked them to do a general inspection to come current on my warranty requirements and address a feeling of the car feeling lose into turns sometimes (I thought maybe it is just me getting used to going to summer tires from winter). So they rebuild the clutch and i finally get my car back four days later with a clean bill of health and them unable to recreate the lose sensation in the steering during a test drive.
So fast forward four five days and under 200 miles driven and I had a rapid failure of my front driver side wheel bearing and cv joint. It was fine the day before then after 20 miles of driving it felt like it was about to go. So this is everything I noticed about my car after I got it back:Transmission felt great. No chatter and fast to respond. When I would turn into a parking spot or pull out of one I would sometimes here a clunk (that had never happened before) Drove fine. It rained the day before the failure (not sure if that could contribute) but when I got on the road the next day the wheel went bad very very fast and the rubbing became so severe I limped to the nearest cellphone reception. A 79mile tow later I am back at the dealership who replaced that the wheel bearing and CV. (my car is actually back there right now because they left a bungee cord attached to the coil and it started to make the clicking rubbing noise so I called them to tow it).
View 12 Replies
Two months ago, I replaced the rear drum shoes, wheel cylinders and seemed after that I was ok until today. I checked the rear brakes and they are split in half. i noticed my abs & brake lights lit up this morning. I would think the ABS is getting stuck? How do I check the ABS? This morning I felt like something was holding back the truck. I continued and when I got home I said to myself, let me just check the rear brakes and thais what I found. Both sides had the shoes broke.
View 1 Replies
What would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 Replies
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
View 2 Replies
I have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
View 14 Replies
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
View 4 Replies
I have a 2004 Ford Expedition and today on the freeway I had to step on the brakes pretty hard to avoid an accident. After pressing, the pedal resistance became really soft and the brakes worked, but were very sensitive (a lot of pedal movement to brake). I had this happen some time ago and I did a complete system flush and no problems since then, but it has to do with how hard I hit the brakes. What could be wrong????? BTW - I never noticed the anti-lock brake pedal pulse at all during this event. I'm not even sure it is working at this point. No dash lights to indicate an error of any sort.
View 3 Replies
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 Replies
