Ford Excursion :: 2001 V10 Not Running On All Cylinders / Check Engine Light Is Not Coming On
Jun 14, 2017
Bought a fixer upper 2001 v10 and it's definitely not running on all cylinders. Also the check engine light is not on and the PCM is not saying it's on (per my code reader) and it doesn't come on when I turn the key on.
Is it possible the previous owner had a programmer of some sort to disable the CEL? If the bulb were removed my scan tool would still show it on. Trying to get it to tell me which cylinders I am having trouble with.
View 6 Replies
Advertisement
The X has been running great, well good enough, lately with no issues. I left work the other morning, and apparently the X didn't want to wake up that early. As soon as I started it up, the check engine light came on and it was running like crap. Had a bad hesitation all the way home. It feels like it is misfiring, but only under load. It doesn't do it if I brake torque it or Rev it up. Only while driving.
The codes I am getting are in the P035x family (typed that way for future searches). P0353 and P0358 are the codes I am getting (along with 4x4 codes for the vacuum solenoid...but that's the solution to other problems not relevant to this!). Being codes for the primary circuit, I popped the hood and checked out the connectors. Both connectors are fine, and tightly connected. I did notice however that cylinders 3 and 8 have other than OEM coil packs on them. These are the only 2 cylinders with those coil packs (they are white and the other 8 cylinders have black coils).
I don't want to just throw parts at it, and I'm not getting a hard miss fire code, just the 2 above. I might try to swap the coils with other cylinders tonight and see if the codes move to those cylinders. It has run like this a few times, but never set a code, and turning it off and back on has "fixed"this in the past.
And just for complete disclosure, while looking for where I saved a password, I found notes from August last year where I pulled codes, and these two codes were present then, with a cylinder 7 hard miss fire code. I replaced the c7 coil with motorcraft cleared the codes, and P0353 and P0358 went away and I haven't seen them since. The plugs are brand new and only have about 1000 miles on them (changed them in September when repairing the misfire and I don't drive it much).
View 11 Replies
I have an old 2000 Ford Taurus that has been having some misfire issues. I replaced the wires and plugs about a year ago and hooray! it worked... until about a month ago when the check engine light came one. Misfire in cylinders 1 and 3... again. I ran some SeaFoam through and it did okay until this week, when the warning/flashing check engine light came back.
It is idling very hard (expected) and feels like it is trying to stall, even before the misfire came back (also to be expected??). So here is the question: is this a coil pack issue, or something more sinister (and expensive)?
View 9 Replies
Last night I was cruising at about 55 when the EPC light came on. At first, I didn't feel anything unusual, but shortly after exiting onto a surface street the engine was definitely running on three cylinders. I immediately turned around and drove the four or five miles home (still on three cylinders) and parked it.
My car is a 2011 with 21K miles. I had an APR flash (Stage 1) done about 2 months ago. (I'm not saying that there's necessarily a connection.) What might be going on? I plan to take it to the dealer tomorrow after resetting to stock program (though I understand it can still be detected). Is it okay to drive it? (Assuming that it will start.)
View 6 Replies
Toyota read the codes wrong and told me that I need a new hybrid battery. That is incorrect info. Codes P0300 P0301 P0302P0303. The codes mean misfire in cylinders 1 , 2 and 3. I have had injector cleaned in the past new spark plugs. If I drive it it gets warmed up and shuts down. It will restart and run maybe 7 more miles the same. The brake light comes on and I have to restart it.
View 9 Replies
So last Thursday I started my car up in the blistering cold and it ran fine for about a minute and started to misfire so I shut it off. It hasn't ran since. When that happened the check engine light was blinking because of the misfire. I didn't have a code reader at the time to read it. now that I got a code reader the damn thing isn't throwing any codes. it spits and sputters sometimes. I've had no previous problems with the car. Thinking It might be a weak fuel pump or bad coils and in not sure how to test them.
View 1 Replies
While I am driving the car it will start to die and skip. Happens randomly. Today I was driving up a small hill and it went quits on me started lurching with check engine light coming on and off. The car will turn over and start, but only for a few seconds before dying again.
Seems to happen when the car is running for a while. Also the ABS light flashes on then off randomly while driving sometimes although It hasn't been an issue. Will be checking tomorrow to see if it starts.
View 1 Replies
I have a 2004 standard Elantra GT. I had to get an emissions test and the CEL light will not stay off. My garage replaced two valves in the fuel tank and the neck to the tank and have done numerous "smoke tests" but can't find the leak. Now they are saying there is something wrong with the computer. They got it to stay off long enough to pass the test, but the light's on again. I see that there was a recall issued because of the cracked exhaust manifold, I think I had the catalytic converter replaced up at the cottage.
View 4 Replies
I have a 2003 Prius, I had an accident and after it was fixed the check engine light started coming on. It would go off after a couple of days. The first time I took it to Autozone and the codes were P3150 & P3130, but the next day the check engine light went off. A couple of days later the light came back on....went back off....next week it stalled on the highway, but it started back up, now the codes it's reading are P1636 and P3002. It still starts up and will drive, but I'm afraid to drive it.
View 2 Replies
I have a 2008 RX350 with 68k on the clock. Received a check engine light for random misfire (P0300) and misfire on Cylinder 4 (P0304), Cylinder ,5 (P0305) ,Cylinder 6 (P0306). Question is what will be causing this to happen. I thought about changing the spark plugs to see if this is possibly the cause. but what else should i be checking?
View 1 Replies
Friend of mine has a 2001 Elantra, not sure of the mileage but it started running really rough, like it's on 3 cylinders. His mech wants to look at the head, thinks there's a broken spring or something.
I asked if the timing belts ever been changed, no it hasn't. My suggestion is it might have lost a few teeth from the belt and jumped. I can't see it being a broken valve spring or something worse because the beta engine are tough as nails.
He said the wires are fine, they probably need replacing too because my friend is the type of person who changes oil and that's it.
View 2 Replies
What to do next. Engine is running on 4 cylinders, #1, 4, 5, 8. Had a mice nest on top of injector #2. Removed mice nest. The mice had chewed through wire for #2 injector and caused bear lead rubbing on the block. One lead rubbed through. Repaired, splised in a wire. Also changed rotor, rotor cap, all sparkplug leads and plugs.
Troubleshooting.
Compression on all 8 cylinders measured to be above 160 psi.
There is spark to all 8 cylinders, including the other 4 cylinders, 2, 3, 6, 7 that is nor developing power.
Fuel rail pressure is 35 psi on idle and spikes to 43 when reving the engine.
The fuel injector resistance all all measured injectors are the same (about 14.8 Ohm). Measured injector # 1, 2, 5, 6, 7, 8. Injector # 3 and 4 is hidden and require too much disassembly. Visual inspection deems wire for #3 and 4 injector to be ok on top of block.
Electric impulse (tested while engine was running) to injector # 1, 5 and 8 are ok, used test lamp to see that there are electric impulse to the injectors. Injector #2, 6 and 7 does not have any electric impulse. Unable to check electric impulse to # 3 and 4. However cylinder #4 develops power. Used moving the sparkplug wire for cylinder #4 to verify that is is developing power.
What would my next step be? Where should i look next?
1. Where is the control module and is it likely to fire to only 4 cylinders
2. Could it be an wire in the pickup element, under the distributor. All wires seem intact.
View 2 Replies
After about 5 miles from my normal place to purchase fuel, My truck bagan to run bad and the check engine light kicked on. Mileage dropped to about 8 MPG. This morning, the truck would not start and after 2 can's of dry gas, I was able to start it (barely).
I stopped at the place where I purchased fuel and at least they admitted that they has to shut down yesterday, stating they received a bad batch of fuel from their source.
Now the fun begins...How do I get the "bad gas" out of my truck?. I now have about 1/4th of a tank. I tried to run a line to siphon the gas and I can not get a line far enough into the tank.
View 10 Replies
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong.
2001 7.3 Limited with 232k miles Bergen County NJ.
View 2 Replies
2001 Santa Fe with 2.4 engine auto FWD 198k miles. When it is started first in the day, the engine sounds good and shifts well. After a few minutes and also after stops, first gear works well but then the following gears do not work well almost as if the engine and the transmission quit talking to each other. Traveling at 60 mph starting up a medium hill, the car downshifted and could not pick a gear. Although I pushed the pedal harder, the car did not respond rather continued to slow down. It acts like I lose 2 of the 4 cylinders in all cases. I replaced the spark plugs and two of them had oil on top of the plugs and also all around the threads. I replaced both coils thinking that one of them was the issue but no change has been observed. I replaced the throttle position sensor; no performance change. I do not believe it is the transmission as I have not notice any clunking, or bad shifting when starting out. While coasting at 40 mph in neutral and my pedal pressed at a certain position, the rpm gauge fluctuated from 3k to 3.6k many times for the duration of 20 seconds.
View 2 Replies
I have a 2001 Audi A4 1.8t (AWM engine, B5 platform). When I start the car, I get misfires on all cylinders (very rough idle, sometimes it stalls when the engine is cold) and the car appears to be running lean. Once the CEL comes on, it runs fine (albeit the slight loss of power do the ECU going into limp mode to correct the problem).
So far, I've done the following myself: new O2 sensors, new SAI pump, new EGR valve, new diverter valve, new N75 valve, new vacuum hoses, cleaned the throttle body, new MAF sensor, cleaned the air filter, new plugs, and new coils. When the problem persisted, I had my mechanic change the timing belt, check for vacuum leaks, change the valve cover gasket, replace the fuel pump and filter. None of this has solved the problem! This is driving me nuts.
At this point, there are only two possibilities that I can think of:
1) Catalytic converter is clogged? I pulled out the pre-cat O2 sensor, started the car, but it still misfired. This seems to mean that there's another problem (i.e., if the cat is clogged, it's in addition to something else).
2) Dirty fuel injectors? I've put two bottles of Techron through the car to no avail. From the outside, they look pretty dirty, so I'll definitely try removing them, cleaning them, and replacing the gaskets. Hopefully this solves it.
Is there something I'm missing?
View 7 Replies
My girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?
View 9 Replies
I have an 05 diesel. I have noticed the last 3 days I needed to crank it slightly longer to start it and it takes a second before ideling normally. It usually fires right up and jumps to life. Today i drive about 45 minutes. Stoped for about 30 minutes and shortly after I started it back up the check engine light came on. Will the Ex flash you the codes or do you have to have a reader? Thought I would try Autozone tomorrow but not sure if they read deisel codes or not. I was suspecting maybe glow plugs but who knows at this point. It seems to be running fine and I checked all fluids.
View 13 Replies
I've got a 2000 ex limited with the v10.4x4. The engine light came on. So I had it scanned. Also the a.b.s light is on.and the overdrive off light was flashing but now isn't. The parts store that scanned it said code was po500. Told me it's a speed sensor but that there's 3 of them on the truck. Which sensor it is.
View 14 Replies
I randomly started throwing a couple codes that have been causing my "check engine" light to come on ... came on on my way into work this morning) . I know that the P0683 code is the Glow Plug Ctrl Module to PCM Comm Circuit (from my code reader), but I am not sure what to do next ... I have the dealer service DVD from 2002 that I will look at this weekend....
View 7 Replies
I have my excursion sitting in a parking lot near my house. The ex will not start, it turns over but not starting? I hooked up my SCT tuner to read the codes, and it is pulling nothing. The Check engine, check gauges and battery light is on. Would a different scanner read the codes?
View 13 Replies
