I'm replacing the oil pan gasket and the new gasket came with a half moon plastic seal. I noticed that there is a grove in the new engine at the rear of the engine but the old engine does not have this grove. Looking for info about this seal, do I need it or not?
View 2 RepliesDid the cam sync replacement on my 96 explorer awd 5.0 l had the tool dropped the sync got it back to where the last one was. Followed the procedure pretty close I did forget to remove the battery cable. So here is the issue I now have 0 fuel to the rail. is there something I might have messed up or left unplugged that would cause this. Did my fuel pump poop out the same time my sync did. I am stumped as even where to start .
View 1 RepliesI'm looking at replacing the valve cover gaskets on my 02 f-250, it's a 7.3L.
Looking at them on line there are many different brands. What have you used on your 7.3L, and which has worked the best for you?
So I've replaced my head gasket on my 5SFE. But after putting my car back together, my car didn't want start. This is how it sounds like (click on the video to watch it).
So I suspected that my timing was off, so I took off the valve cover to check the timing marks on the camshafts. So the two timing punches lined up like so (I only took picture of one of them)
Though I'm not too sure what the two dots mean on the exhaust camshaft since there are not two similar dots on the intake camshaft.
So I'll assume that I have my camshafts lined up properly But how do I know that it is in time with the pistons?
Could it be the distributor? I am not too sure if I installed it correctly, but I did follow instructions in the Chilton manual.
On the other end, there were two vacuum lines that I'm not sure if I installed correctly. I'm positive that the left two pipes are correct; however, I'm not too sure about the two on the right. This is mounted on the cylinder head.
Changing the valve cover gasket on the 4 cylinder 2.4l. I was going to change mine's. Didn't know if there are any special tips like sealant to be used, loosening bolt sequence or tightening sequence, torque values.
View 9 RepliesRecently the timing belt slipped and in turn shot several valves. After replacing the head and gaskets there is a small oil leak between the head and block. Can i tighten that head bolt a little? What is the best solution?
View 1 RepliesI'm replacing the valve cover gasket on my 94 Honda Accord. I've heard all sorts of crazy opinions on what needs to be done while installing the gasket such as using various sealants or lubricants. Should anything be put on the gasket or should I just drop it in and screw the valve cover back on?
I'm also replacing the spark plugs while I'm at it. Is there anything else I should do while I'm in there?
My mk4 sat for a while and upon starting up was misfiring. I checked for pvc leaks and didn't see anything but went ahead and cleaned my maf sensor and decided to pull my coils. Cylinder 1 had oil on the tip and around the spark plug which to me spelled out a bad valve cover gasket. I got all the parts to do the inner and outer gaskets and replace the coil and spark plug, however we got a snowstorm and my luck a rabbit got in and ate the wiring on one of my fuel injector connectors.
So went ahead and put on the new gasket, replaced the coil and plug and bought a new Fuel Injector Connector and spliced in onto the Injector "Pigtail'. I double checked everything was reattached properly and let the gasket sealant dry for 24 hours. I went to start it tonight and after trying to turnover it completely cuts out, wont even start up. I'm extremely frustrated at this point and am thinking the rabbit must have gotten to something else unless I did something wrong in the process of repairing.
Had the head gasket replaced and metal machined due to HG failure. 2001 Forester, 120K miles. After I got it back, a bad oil smell. Cleaned and sprayed it, still there, though less; seems to be on drivers side. Comes into cabin from the air vents below windshield when stopped.
Could it be the line from manifold vacuum to brake master cylinder ie servo amplifier? Or something else?Should I worry? The car seems to get about 15 mpg, used to get 18 mpg, and the check engine MIL is on.
i have a 06 explorer with the 4.0 V6. 4x4 XLT with 106xxx miles. i just bought this thing back in January. of corse, i didn't get an ext warranty. well the past couple months its been loosing power, its got a stumble and seems sluggish. its losing water. no water in oil, no oil in water, don't smell coolant in the exhaust. yesterday i went out and looked and found at front of head on pass side at front cyl, there was coolant from head gasket down the block and also in the valley of the block. i started the engine and once warm, everything was dry. shut it off after about 20 minutes and still nothing wet. this afternoon the only wet spot was in the valley which was dry after running yesterday. is there anything else i can check before tearing it down? with the water in the valley, it looks like it could be coming from the thermo housing.
View 6 RepliesVehicle 2007 Ford Explorer Sport Trac with 4.6L
Ok, just did a head gasket replacement. Everything is now hooked back up. Now when we try to restart the car, we get lights, but nothing from the starter. Also the OBDII code puller can't communicate with the car. Also the security light flashes very fast when you try to start.
I have a 1990 legacy and just replaced the water pump gasket and now it is leaking out of an upper bolt head on the pump and how to cure this....
View 1 RepliesI have a 2003 Explorer with the 4.0 K motor. It has a vacuum leak and the check engine light will come on from time to time. My work buddy has a high end computer and it showed that the driver side bank was running lean. The computer showed the O2 sensors to be working fine, and I replaced the PCV valve. All other vacuum line appear to be in good condition and I tried the spray test with the break cleaner with the motor running. This is leading me to believe the air intake gaskets where due for replacement. Here is my problem, I can not get the last bolt out of the plenum. The one on the driver side up against the fire wall. I tried to remove the cowl in order to get a straight shot at it but I can not get the seem seal to break free.
View 4 Replies2007 Sports Trac .. Does the motor need to be removed to replace head gaskets? 4.0 sohc
View 1 RepliesI have a 2003 Eddie Bauer explorer with the 4.0L SOHC . I have a coolant leak from the passenger side that is not a water pump issue.
When removing the timing chain cover with the engine in the car, do I need to remove any accessories ( power steering , alternator etc. ) or their brackets?
Soon my rear shoes will need replacing in my '02 . I've given up searching for info on how to replace them. Seems all the links I find are for vehicles that have rear disc brakes and mine are drums. Is this a do-able thing or should I just hand it over to a shop? I've done my share of brake jobs on other vehicles but not this would be my first Ford.
View 11 RepliesI purchased my first truck 2 weeks ago private sale a 2001 Explorer Sport Trac 4v4 4.0L. I noticed it had small leaks coming from transmission and front differential gaskets (the diff is silicone) but the oil levels remain fine. Within days I heard a loud hum coming from the engine for 10 seconds then immediately after i was slowing down for a speed bump and my truck tried to stall and since that point it was riding very rough at low speed/idle and sometimes giving it gas seemed to just kill it. Next day a check engine light comes on and I get it checked It was Bank 1 running lean and B1155 (Output shaft speed signal) which concerned me from what I found it is located by the transmission oil filter which has the leak.
A few more days later I broke down on the side of the road, the alternator had died and killed the battery, I replaced the alternator and belt, replaced the 6 spark plugs, 3 of which i removed way to easily with my hands and all 6 had an incorrect gap. Initially the car was still rough but now with the new plugs it is drivable but still a little weird on startup and idle and a little bit of the shakes around 60-65mph and seems to be over actively shifting soon as i let off the gas even a little bit. Today I had the check engine light assessed again, now Bank 1 and Bank 2 are lean, still have the B1155 as well as a new C1676 (Battery pack voltage out of range) which light research said it could be ABS module or it could be a false code from being jumped days prior and that code wont clear on its own.
I was surprised by a leak and identified where the water was coming from, the bottom of my vehicle. It's from a gasket or seal on the front of the pan near the flywheel. 1994 Ford Explorer 4X4.
View 6 RepliesI just changed my spark plugs the other day and since then my engine is hard idling and skips and jumps while I'm driving it. I'm being told I either need to change the spark plug wires or the coil packs. So my question is which do I need to change? And is there anyway to test which one I need to replace?
View 12 RepliesI have a 2000 Ford Explorer with 4.0 SOHC engine, I have had some cold start problems. I cleaned the IAC and the problem went away for a few months and then came back. Two days ago the temps got very cold and it would not start at all, I re-cleaned the IAC and still no start. I replaced the fuel pump with an aftermarket pump and engine started right away. Now I have a rough idle, bad skip and bad exhaust odor. I am still thinking IAC but I am concerned that the aftermarket fuel pump is pumping to high pressure or that I may have crimped the return line. I have driven about 30 miles hoping the computer would make adjustments, still runs rough and the check engine light has not come on.
View 12 Replies4.6 engine had blown head gasket. right side. Pulled heads had checked for cracks and resurfaced. Reinstalled heads, but I still have a problem with oil pressure on right side. Chain doesnt seem to tighten and lifters rattle.There is good base oil pressure.
View 16 Replies