Ford F-150 (2004-2008) :: Hesitation When Accelerate From A Stop Sign
Aug 6, 2016
This morning as I was driving to work, my truck hesitated as I tried to accelerate from a stop sign. I pressed the pedal and nothing, almost felt like it was going to stall. After about 3 seconds it started driving again and I had no further issues. It seems to only do this in the morning when it is cold. It has done this a couple of times before, but usually it recovers almost immediately. I had no CEL come on. 2007 F150.....
View 1 Replies
Advertisement
2008 golf city... So I bought this car about 2 years ago and the last couple weeks its had trouble starting and will sometimes stall out when your about to accelerate (from a stop sign) the mechanic I go to replaced the a couple relays under the drivers side dash, however I it hasn't made it better it actually made it worse as now it won't start at all the last 2 days. It rolls over and tries to start just doesn't. Its my only car and I already missed a week of work for it ( I commute ) I need it fixed. I believe the relays where the EMC is what he said number 249 I believe.
View 3 Replies
I have a 04 lariat f150. Problem is every time I stop at a light or stop sign I hear and feel a bump. Coming from the rear I guess . Had my truck aligned asked the alignment person about the situation he said ford just do that. True or false ...
View 2 Replies
My isf for couple months now and love the car. I have an 08 which only 7k miles on it. Lets say at a stop I start to accelerate, I notice a slight hesitation before it picks up around 1-1.5 rpms. Under hard acceleration I don't notice it, but with nice and easy acceleration that slight hesitation is kinda annoying. Not sure since car has such low miles on it if I need to run fuel injection cleaner or something, of if something else could be wrong. I kinda mention it to the lexus service manager and he said something that next time I bring the car in that he'll let the mechanic do a tranny ecu update of some sort? I didn't know that there was such a thing.
View 14 Replies
So after a decent drive when I get to a redlight / stop sign / etc the truck will idle rough and shake but giving it a little bit of gas (1k RPM) seems to smooth it out however it doesn't throw any codes or the CEL. The truck is a 2008 F150 with the 5.4 and 90k miles.
I've searched quite a bit on this issue and I can't seem to find any real fixes other than swap parts out until something works and I've heard everything from filters to cam phasers or low oil pressure (I will be taking it to the mechanic to check the oil pressure)
so far I've:
Replaced the air and fuel filters
Changed the oil and oil filter (synthetic and OEM filter)
cleaned the MAF and cleaned the throttle body
also is 2008 equipped with an IAC Valve because I've read that it wasn't and I can't seem to find the IAC if it is.
View 14 Replies
Trying to troubleshoot a very intermittent (has happened on two different occasions during the last 1,000 miles) hesitation from a stop-light. I've been recording engine parameters (Torque application) on both instances as these have been during longer trips after a period of highway driving. 2004 Excursion, 112K miles.
This feels kind of like severe turbo hesitation (4 to 10 seconds trying to start out before it kicks in) but I don't think that's it. The turbo is a new PowerMax turbo replaced 5 months ago. VGT readings seem pretty normal. The EGR valve is new -- the first instance was with the old and the second was with the new. I've also recently replaced the EGR and Oil coolers (before this).
Here's what's interesting in the captured data though... Normally when I coast into a stop-light the indicated engine load stabilizes at about 40-50% and VGT moves to about 65% to 70% at idle. The two different times this happened (actually multiple times at stop-signs/light close to each other over 5 minutes or so for both of these), when I have coasted to the stop, the engine load increases from low values during coast-down (0% during freeway coast-down or 19-30% during other coast) up to 99.6% (or other similar high values) at idle and VGT seems to be full closed at 85%.
There is absolutely no response to the throttle in this situation for 5-10 seconds. I've either been goosing the throttle a bit or putting it neutral and revving it up first to get things going again. When it finally catches and starts accelerating with power, indicated engine load drops to 50-60% again and VGT opens up to 40-60% or so. None of the other parameters I've been capturing seem to read strangely during this that I recognize. No issues observed during cruise and power seems good. No pending DTCs or engine light.
Here's what the data points I'm capturing (once each second):
Boost
Calibration Input Volts
ECT
EOT
Fan RPM
FICM main volts
Fuel Injector pulse width
ICP
ICP Volts
IPR Duty cycle
RPM
Engine Load
MAP
Trans Temp
VGT Duty Cycle
EBP
EGR Commanded
EGR Error
Added today but not captured during these issues yet:
IAT
IAT2
Baro
Accel Pedal Position
Mass Airflow Rate
Mass Fuel Desired
View 14 Replies
I recently had an oil change and 30,000 mile service at a Honda dealer. Car was running perfectly when I took it in, but now infrequently 'moans'. The low moan usually happens after I have driven the car for awhile, at a stop sign and I slowly accelerate to take off. In SF, there are lots of stop signs! As soon as I accelerate to full speed, the noise stops.
Can happen as often as five times in ten mins or not at all if I am only driving on the flat. Have had it back to the dealership numerous times since, test driven it three times with them and only heard the noise once (with a technician). They cannot find a reason for it and seem to have given up.
The car is a 2009, has 16477 miles on it and is under a Honda Care warranty. I purchased the car in 2012 as a preowned certified Honda and have had no problems with it and as I only drive about 3000 miles a year have had no previous services or maintenance issues.
View 2 Replies
When I accelerate from a dead stop I have this squeaking that comes from the back of the truck that goes away after a few seconds. Then when I get up to about 50mph I have this really annoying vibration. Its not a real heavy vibration but it is there. I am thinking it could be the universal joints, am I way off here or what?
View 6 Replies
I have a 2008 ford f150 4.7 liter 4x2 & the problem I am having is when coming to a stop when I accelerate there is a slight shimmy in back end or could be described as a vibration for just a few seconds and then you don't feel it anymore until you come to a stop & restart. Once you have pulled off it will not do it anymore out on road. I checked fluid & it is not low in back end. Transmission shifts good so what could cause this.
View 2 Replies
I have hesitation as I accelerate especially starting from a stop. It will continue until cruising speed. Funny thing is when I put the cruse control on the hesitation stops and it runs fine. If I want to accelerate while on cruse the hesitation starts again until I let off the accelerator. Is it the TPS ? I changed it two months ago.
View 8 Replies
I have been experiencing a slight hesitation when I accelerate from a stop. It almost feels like its going to stall for a brief second then it picks up and accelerates normal until I'm at a complete stop again. I have the 2016 sport with the standard 2.4L. I currently have 2200 miles on it now and when I go in for my initial suggested oil change at 3000 miles ...
View 25 Replies
I have a 1988 Toyota Camry. I was driving to work this morning, the car was driving fine. After about 10 mile or so, I stopped at a red light, when the light changed the car wouldn't accelerate it seemed to have a really bad hesitation. If i let off the gas it would idle fine, none of the warning lights are on. However, when I give it more gas the car doesn't have any power at all. It has plenty of gas in it and the exhaust has no signs of any oil or water in it. I was thinking it may be a bad fuel filter or a tank of bad gas.
View 6 Replies
I have a 2003 Toyota Tundra V6. The problem I have with it is it hesitates. It does not happen ALL the time but it is very frequent. Sometimes it happens when I try to accelerate from a dead stop and other times while I am driving along (does not matter what speed). It will usually hesitate for a few seconds then everything is normal. The check engine light thus not come on.
I took it into Toyota. They duplicated the problem on the first test drive but did not have their equipment hooked up at the time. They kept the truck for over a week and finally got it to happen again. I guess they must have only been going on short test drives because it happens to me multiple times a day. They told me it was the throttle body and it needed to be replaced. My jaw hit the floor when they told me how much they charge to replace it. I ran this by a couple of friends who work on cars on the side and they said it sounded like the mass air flow sensor needed to be replaced. Since this was much cheaper than a throttle body, I replaced that. However, it did not solve the problem.
View 2 Replies
We bought yesterday a 2004 Prius with 73K miles. This was (unfortunately) a private sale. When my husband drove back home with the car, the VCS, ABS and ((!)) yellow came on when he reached 60mph and above. He also noticed a lot of noise when accelerating and the car was shaking. The noise is also there at low speed and when accelerating it is so bad and feels like something is rubbing?
This morning, we decided to try the tire pressure to see if this could be the issue. After correcting tire pressure (it was actually very bad), the lights went off and we decided to try it on the motorway. The car was noisy to start off but as soon as we hit the motorway, the sound was getting worse and worse. I could feel my passenger seat shaking under me and the 3 lights (VCS, ABS and ((!))) came back on and stayed on until we got home.
What was the issue in the end? We have spent all our savings in this car and can't really afford expensive repairs few days after buying it. We are just gutted. Oh and we have a 2011 Auris Hybrid with 15K that runs superb. My dad owns a Prius too and so I can tell the noise is just not normal- at the same time, perhaps a 10 yo Prius is supposed to do this noise?
View 10 Replies
I just purchased a 2008 passat, 2.0T 6spd manual last night and I noticed today, when sitting at a stop sign it has slight idle issues, (goes up about 200-400rpms) then back down to normal idle. Doesn't seem to be causing any issues, its just pretty annoying, and everyone next to me thinks I'm trying to race them.
View 24 Replies
Last week I was changing the oil on my wife's 2004 Camry (130 000 kms). I noticed quite a LOT of corrosion around the positive and negative battery terminals.. so I decided to clean them.
I removed the negative without any problems but I could not get the positive off. I decided to use a hammer to move the connector back and forth. I was surprised with how much force I had to use to break the connector free.
Once I replaced the oil I tried to start the car but it would not start. I check the voltage and I was down to 10 volts. Obviously I had damaged the battery in getting the positive terminal off. A quick ride to the auto parts store and I had a new battery.
I installed the battery and took the car out for a spin. The car drives normally but it will NOT idle after it has been warmed up. If I come to a stop sign, the car will idle low and stall.
I have already verified that the battery is at full charge and the battery is being charged when the engine is running. No 'Check Engine' light has come on.
View 14 Replies
We bought the car this past summer. Notice steering wheel vibration during braking. Figured rotors were warped. Which they were. Replaced all 4 rotors and pads. Now I notice that when I brake at a stop light or sign, it feels like the brakes are catching and slipping. Jerking movement. Like you are pumping the brakes slightly. Brake pedal seems slightly mushy too. Maybe air in brake lines?
View 8 Replies
I've read the throttle lag posts with interest. Ours only lags when performing a "California" stop where you go from the brake to the gas and look for an instant pick up. Seem to have about a second of delay before anything happens. Of course this causes all sorts of unnecessary lurching and I don't like it. Does everyone else experience this as part of their throttle lag problem?
2004 V8 Touareg
2003 GTi 1.8t
View 24 Replies
I have a Hyundai Santa fe 2004 6cyl 2.7 L , AWD. I am having problem of slow acceleration which is worse after a stop sign or red light. Sometimes while taking turns I feels like that I will not move and I was lucky to be not hit by a Car coming from opposite direction while taking a left turn today.
The Truck’s exhaust pipe broke recently and a auto garage welded it. But I am facing the above problem immediately after the repair of exhaust pipe. If I put more pressure on gas pedal then a mal function indicator comes and today I took it to another mechanic and he gets the error code of P0303 –engine misfire and wants to charge me ~ $600 $ to replace spark plugs and wires. The malfunction indicator goes off also while I am driving and can comes back after a while or a day. With the indicator on, the car drives erratic (minor jolts ) for few meters and then its fine. Since when I am driving on highways then I can go higher speeds without any problem. Is it still misfire issue???
View 11 Replies
Having throttle hesitation problems. This is the 3rd time I have had it in for this problem and they can't figure out what is wrong. The vehicle moves slightly forward from a stop and then goes dead for a few seconds then seems to recover and go.
View 11 Replies
Here's the story on my truck. Spits and sputters between 40-60 during heavy acceleration and on rare occasions will jerk/pop while at a steady speed. No engine or wrench lights. I thought it might be the fuel filter and changed that, it didn't work. I also ran two bottles (on 2 separate occasions) of Duralube extreme fuel system cleaner, that didn't work either. So, I took it to the Ford dealer for a diagnostic. They had a hard time getting it to act up but said it finally misfired on #8 and recommended replacing the ignition coil and plug. I did that, still have the same symptoms. So, I thought it might be the fuel injector and changed that. Still same symptoms and ZERO dummy lights.
After several YouTube videos, I thought it might be the TPS and got one. Before I changed that however, I cleaned the Mass Air Flow sensor, still same symptoms. I finally changed the TPS, but the engine wouldn't start or run at all, no warning lights yet. When I put the old TPS on, it would run. I unplugged the TPS and it still ran but very rough. Now the engine light IS on! Thinking I purchased a bad part, I took it back to O'Reilly's and they warrantied it out and gave me a new one. I had 19 PO codes. I changed the TPS again, and, it won't start or run at all. Put the old one on and it runs. They cleared the codes and told me they think it could be the ECM/PCM.
Why will a new TPS not work? I still have the same issue of hesitation @ 40-60 during hard acceleration. No hesitation during a moderate acceleration.
View 1 Replies
