1996 Ford Ranger 4-Cyl. 90,000 miles. 5 speed manual transmission. When the truck is driven 10-15 miles and heats up the clutch will seize in the up position. Once the engine is turned off then it can't be turned back on because the clutch won't depress. After the truck has completely cooled down the clutch and the transmission again work fine, as long as I keep any use under about 10 miles.
View 6 RepliesThis is unusual. After driving into town for new tires, the clutch pedal was hard and I could not depress it after the tire tech parked the truck. It did finally depress with a pop, though the pedal functioned there after the clutch did not function properly.
At times it seemed to be ok at other times it seemed weak. I stopped by Autozone and checked the fluid, seemed low and I added some. Continued home not completely confident that I would make it. Had to make one stop along the way.
Once again the clutch pedal was stuck at the top and would not depress. I finally slid the safety switch up the clutch shaft to start the truck, when the engine started the pedal depressed. I was able to continue home but the clutch is not functioning properly.
I've had my truck a few years now but for 2 it was basically parked. When I started trying to use it again I am having issues with the clutch now. When it is cold everything is fine, but on hot days or after I have been driving for a while It will lock the pedal up and will not let me dis-engage the clutch at all. Sometimes when it does eventually let the pedal down it will go to the floor and stay there for a few seconds until it slaps back up and engages slamming the truck into gear.
I have yet to try much. I'm not good at working on anything other than stereos in cars but I am willing to try. My thought is some water got into the system and is boiling in the lines but I am not sure. Places to start? I really need my truck going and the couple places I've taken it dont even want to try it seems like.
So, For the past week or so, I've been noticing that my clutch has been getting harder and harder to depress when I go to shift. I only have 1500 miles on the car and picked it up 3 weeks ago. When I took delivery, the cars clutch was silky smooth.
This "tightness" is almost as bad as my 6MT clutch on my old subaru (which needed to be replaced because the spring on the pressure plate tightened). What could be making the clutch feel so heavy? I'm not too familiar with the VW clutch. Is it hydraulically actuated? If so, maybe the fluid is low or leaking?
I've got a 2008 Subaru Outback with a 5-speed standard, 50K on it. Lately, when I depress the clutch pedal, it makes a whining noise, in any gear or even in neutral. It goes away when I release the pedal. But it also stops making the noise when the engine warms up. That's the part that confuses me.
View 4 Replies2007 Accent pedal won't depress. Bearing making noise for a few months. Is tranny snout toast or is it fixable?
View 2 RepliesFor a little wile now, I have had a growling noise when I depress the clutch pedal with the engine running. It mostly does it when the truck is cold and goes away after a few uses but was getting worse and taking longer to go away. The transmission shifts normally, the clutch operates normally and it does not make the noise if I put the transmission in neutral and let the clutch out. So I'm thinking dry throw out bearing.
I did an oil change Monday, and while it was up on the ramps, I decided to check the transmission oil level, I mean its got a 181k on it so its about time to check, right. Bone dry. I put about 2 qts of gear oil in the transmission that the service manual says has a 4 1/4 pint capacity. I took it out for a drive today and the noise is gone. Go figure.
I only drive the truck one or two times a week, sometimes less so in a couple of weeks I will check the transmission again for a leak, but there was no sign of a leak when I was under there Monday. But is still shifts smoothly, makes no noise.
Sometimes in the morning the AC will work just fine, but after a while it stops working. It looks like the clutch will not engage and I don't know how to troubleshoot it. I'll take a picture later on today. I'm wondering which part is what, and what might be causing the problem.
View 9 RepliesHe has a 96 explorer and his ac compressor clutch was cycling on and off. So he went and bought 2 20 ounce cans of 134a and proceeded to add it to the evaporator service port. Of course a lot of it sprayed out side of it as it did not fit well (duh). So he has no Idea how much he actually got in there out of the 30 or so ounces he dispensed. He is laughing at himself with me on this. He says hi ahead of time
I have access to good gauges and a reclaimer and vacuum as I work sometimes for a residential ac guru. So what to do? I was thinking the evaporator should be changed out but I want a second opinion. Then vacuum and add new 134.
I just got done changing a/c clutch on a 96 f-350 5.8 because it was making a lot of noise. The new one is just as bad. Would the air gap cause this? When I took it off I could see it was hitting the pulley. The gap was 0.21 is that the specs on it.
View 3 Replies1996, f150, 300, 4x4, 5 speed, 296,000 miles... My pedal goes almost to the floor before the clutch engages and about a half inch, maby less, of travel back out the clutch disengages. I think it is about time for a new clutch. My question is what is the best clutch to put in my truck?
while i have the transmission slid back to replace the clutch i am planning on replacing the slave cylinder while im in there as well. Any particular brand better than the next on that item? Are there any other items that I should think about replacing while i have the transmission slid back to do the clutch?
1996 F150 4x4 with 300/6 and M5OD mazda tranny. 145k miles on it and looking really clean, and just the truck we wanted. It used to be well cared for, but has been a bit neglected since the owner passed away.
I spent a few hours searching the forums here and didn't find anything matching my symptoms exactly so I thought I would just jump in a post, but if I missed a thread feel free to redirect me.
I've got a bit of a rattling noise as the clutch engages when taking off in first. Once the clutch is fully engaged it's quiet and it shifts well and smooth. Noise also occurs (but less so) if I don't match RPM's and ride the clutch into second or third. I don't think its engine noise from lugging or anything because it goes away as soon as the clutch is fully engaged or disengaged.
Changed the trans fluid last night and no different, Clutch fluid reservoir is full, clutch travel feels good, master cylinder looks good, (slave is hidden, but looks dry though dust cover) a little play in the white bushing that holds the clutch pedal bar in place, and the plastic pushrod that goes into the firewall, thinking about replacing this linkage.
I work on big diesels for a living so i'm not scared of getting greasy. I'm almost inclined to think someone did a clutch job without resurfacing the flywheel. Is there an improved replacement for the pedal bracket and linkage? I don't mind just doing the clutch, but I don't want to be throwing my money away.
I have a 1996 Ford Ranger which was manufactured in 08/95. The key will crank the trunk fine, but it when put into the off position nothing happens. It continues to run as normal. You can even take the key out, but the truck runs like normal. Could this be bad ignition switch? The key seems to be doing its job because I can see the plastic pin(? I am not sure what its called) move back and forth down steering column when the key is turned.
View 7 RepliesMy 96 ranger had lost a brake pad coming out of the mountains. I replaced the rotor but the ABS light came on as well as the check engine within a week. Several issues the clock spring was bad, replaced. The cam position Sensor was bad, replaced. I had this at a shop in a small town. While I was there they ran diagnostics.
At first the ABS module was sending data and gave them some info. Suddenly there was no more data stored in the module. They ordered a new ABS module installed it and replaced the LF sensor cable. Both sensors were cleaned prior to this.
The new abs module required a trip to ford to reprogram. At the shop they still could not get the light out. I took the truck home to my ford dealer and they said bad abs. Got a new (rebuilt Mfg discontinued) Installed and ford said this was bad with a code c1102. 4 w 4wd installed needs 4 w 2wd. ordered a new abs. Ford said same code again and the tech said that the ABS is not communicating through the obdii port.
My thoughts are the reader they used at the small shop was defective and either shorted out something or blew a fusible link. I am told this is 4 wheel abs with the rear sensors are on the pumpkin but after looking at the diagrams I do not see a RABS fuse. I have tested all fuses, and the shop replaced several relays. The pcm and ABS diodes check ok. Perplexed.
I want to get rid of the ringing alert when driving - actually I want it to go away for ever. I live on an island and this old truck has an "island only" registration and will never have to pass inspection again.
View 1 RepliesMy engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 RepliesI have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
I have a 96 Ranger 3.0 auto that is hitting 300,000 miles. I've got a 302 that i build for my F150 but know i'm thinking of transplating it in the Ranger. Is it a big deal in putting a SB in place of the V6.
View 4 RepliesI seen on this site awhile ago something about a fix for the heater control door, I have a 1996 Ranger and all I have is Hot heat and cannot cool it down with the temperature control.
View 2 RepliesMy clutch is not disengaging when i push in the clutch pedal. I have good clutch pressure, I have to basically rpm shift my way through the gears. Is a dead slave cylinder the most likely culprit for this? if so is there any special information i need to know when it comes to bleeding out the new one?
View 1 RepliesI recently purchased a 1996 Ford Ranger with the 4 cyl. engine. The first 10 days I owned it it ran just fine. I then took a an hour drive to another city. After the first few stops there, as the temperature outside reached about 90, It started to sputter and idle very badly. After I got rolling it would would run fine. I decided to try to make it home. It ran fine at freeway speeds of about 70 mph. I had to stop once; it stalled out and would not start again. After waiting about ten minutes I tried again. It was still running rough, but I was able to get rolling and drove the rest of the way home without any problems until I was in town and had difficulty keeping it running at idle.
The next morning it ran fine again. A local mechanic changed the fuel filter, but the problem came back as soon as the temp neared 90 degrees. A mechanic friend who witnessed the problem said that it definitely sounded like a lack of fuel and not an electrical problem. Is there a way to troubleshoot without swapping parts? If the fuel pump is failing in warm weather, how is it possible that it runs fine at 70 mph, but not at idle? Engine temp gauge looks good. I did get one code after it died the first time (lean mixture, I think he said).