Ford Super Duty (1999-2016) :: 2001 F350 - ABS Light Comes On - Metal Grinding Sound
May 2, 2016
2001 f250 7.3 crew
So, Saturday my abs lite comes on. Later that day I hear metal to metal sound for a couple of secs then it stops. Then the next day while driving I get intermittent sounds that sound like I'm dragging metal down the pavement. I see nothing but I'm thinking hub bearing. (Needle)
I remove the hub assembly from the knuckle and can find nothing wrong. I even picked up a new hub just on case. Now I'm stumped. Can't figure out what the sound was or is. Axle has a little play going into the housing but figure it would have due to the only thing holding it in place is the hub.
The only thing left in the area that could make the sound is major --the actual gears to to the front end. If the bearing isn't causing the metal grinding sound I've no other idea other than that....
View 2 Replies
Advertisement
I thought i heard this yesterday when i left work but i was tired and said its in my head, THEN i go to leave right now and sure enough its a real sound, you can hear it very well through the front grill and then if you turn the volume up you can hear a ticking sound ever half a second or so, it also speeds up when i was pulling on the throttle cable. And after the truck fully warms up it goes away.......
View 14 Replies
I have a loose, binding, metal on metal sound on my steering wheel shaft. I have removed the steering wheel, replaced the clockspring, because when I removed wheel clockspring was in pieces and I thought that might be the issue. Guess not, because I'm still having problem. Other than having to remove or replace the whole steering column...
View 2 Replies
Have an f350 4x4 diesel that when I drive slow and especially turn to the right it makes a grinding noise. It seems to either go away or just gets muffled by road noise when cruising. The ball joints were bad so I replaced them and I figured with this especially when I turn right it had to be a wheel bearing so I replaced both of them and still same thing. Don't want to throw money at it hoping to fix the issue. Also front duff is full of oil.
View 5 Replies
My buddy's 2001 7.3L F350 has had 3 transmissions. Rebuilt and used. Once the new trans is in he goes like 15 miles and then is starts shifting hard and grinding gears. What this could be?
View 8 Replies
I got a 2001 f350 got a noise in my left front wheel i know its not the wheel bearings, it only makes the noice when the locking hub is unlocked i did jack the the truck up and spun the wheel got a faint grinding noises form what seems like the locking hub so my question is bad locking hub or needle bearing holding the axle shaft??
View 3 Replies
2001 f350 4x4 dually 7.3 powerstroke, I recently replaced the hub assembly, stub shaft and seal, u joint, ball joints on the front drivers side and now periodically the truck makes a grinding growling vibration coming from front drivers side and stops after hitting a bump...
View 3 Replies
I have a 2001 Ford F-250 with the gas v-10. Yesterday it started just fine as always. Today I get into it and it starts to turn over just fine then starts to make a grinding sound and the truck won't start. I have had a fuel issue in the mornings with once it started you had to barely press the gass to keep it running. But never makes a funny sound and always runs fine. This only last for a couple of min and then it runs fine for the rest of the day. The grinding is not the starter. I took it off and had it checked and it was fine.
The truck had been using oil. When I checked the oil level it was low but it was still on the stick. "I know a motor needs oil to run smooth but it's my dads truck and well let's just say he is not the best on maintenance". Also I smelled the oil and it does have a gas smell to it. So it definitely does have some gas in the oil. I tried to light the dipstick with a lighter and it wouldn't light. So not sure how much gas is in it but that's what I did.
So the question is, would something just in mid crank go bad and then not let the motor crank. Truck made no weird noises before this so I find it hard to believe the barrings just went out in mid crank and now it is shot.
Also I just checked compression on front cylinders.
Driver side read 75lbs
passenger side read 100lbs
View 4 Replies
My abs light is on. The guy I bought it from said he thought it was the sensor but who knows. Is there a way to test the sensors to see if they are working? Also can any other possible issues to look for? 2001 f350 7.3 xlt...
View 3 Replies
I currently am driving a 2001 F-350 V10 SuperDuty, and recently the battery light was blinking. I replaced the alternator in it, but it didn't work. I thought it was bad so I went and got another and it still didn't work. Turned out that the alternator wasn't big enough. I then went BACK and got a larger alternator, and it still won't work. Now the battery light is solid, and I'm getting absolutely no charge out of the alternator. I checked all the fuses and nothing is wrong. It seems like all the things you think could be wrong are running perfectly fine! What could be wrong. The truck will start, and idle, but will run off the battery only.
View 14 Replies
2001 F-350 4x4, 5.4 automatic.
Where to start , check engine light is on. Nothing seems wrong , trucks running good , nothing happened , just the light. I kinda like the truck so I would like to find out what its issue is?
View 2 Replies
2001 f350 v10, initial problem was when i came to stop at light it idled rough. I changed all plugs,injectors and COP, and bad connectors thereto. Changed the clock spring as well. Now the truck idles like crap at first start of of the day then run fine there after. Replaced IAC, TPS, Temp sensor. Condition getting worse and now the temp gauge does not work. I am thinking maybe CAT Converter loaded up?
View 2 Replies
2001 f350 7.3 diesel and I come up with the codes for upper and lower dual generator fault. I have only one alternator not the dual.. I checked the gauge and it is running at 14 consistently. But the service engine soon light keeps coming on...I clear them and they come right back... Alternator is only 2 years old and not a rmf..
View 1 Replies
My 1999 Ford F350 Dually 4x4 started making a grinding noise every once in a while about 3 weeks ago. Now it is doing it quite often, randomly as I am driving. I do notice the noise stops when I stop the truck, or when I flip the switch to 4x4 and back while driving.
View 1 Replies
I have an '01 F350 super duty dually, 7.3L, auto trans. Over the past weeks my overdrive light on the gearshift would flash intermittently, maybe once every couple weeks. I chalked it up to a prior theft attempt where the steering column was damaged, and had turn signal/hazards issues after that.
Over the past few days my reverse gear has taken longer to engage, and is hard getting into the higher gears at speed. As of yesterday, reverse is out and won't shift out of second. Fluid level is good and clear. Could this be a PCM issue, or some sensor or relay?
View 1 Replies
My 2006 F350 is giving me grey hairs. I'm trying to figure out what's going on with it. I have been getting an occasional (more often than not) grinding noise from what seems to be the front of my truck. It will do it from a stop, under light, moderate, or heavy acceleration. Doesn't matter. If I let off the throttle momentarily it will stop until it shifts and will grind again through all shift points it seems.
Logic says it's got to be the wheel bearings or locking hubs. I recently did both on both sides to no relief. Because this is an 06 it had a different hub set up then the previous years which I've read a lot of info about (needle bearings). It doesn't make a lick of difference if hubs are locked or on auto. If in 4x4 (ESOF) or 2wd.
As mentioned I replaced both wheel bearings with FORD parts and both locking hubs From FORD as well. (Small fortune). Axle u joints seemed tight. Greased me up but no play.
View 6 Replies
What we have is a 2011 F-350 with the ambulance package (obviously) and it has started making a very annoying sound from the front end. It has been into two different Ford Dealerships and they have not been able to remedy this issue. What happens is, when we are backing and turning, the front end makes a bad metal on metal grinding noise. When going straight down the road no issue just turning while backing. I know this is an ambulance and has the ambulance package but I think from the cab forward should just be all ford right?
View 2 Replies
I replaced both front bearings, calipers, brake pads, now I have a grinding noise on the left side front stops sometimes when you step on the brakes? 1999 F350 ...
View 6 Replies
Just last night, out of the blue, I've got an odd rumble at idle. The noise goes away under load and any time the rpm's are up over ~1300. It sounds like metal on metal vibration, but I don't see any loose exhaust parts.
I've looked at threads saying possibly a broken flex plate. Other than the noise, would there be any other symptoms? I don't notice any loss of power. I suppose I could pull the inspection cover and take a look, but I don't have any experience with auto tranny's and don't really know what I'm looking for.
View 1 Replies
The issue is with my 2000 F350 crew longbed V10. Other than a BTS trans put in a little over a year ago, and FoMoCo motorsports headers, the whole truck is bone stock. Oh, it has that fantastic auto-hub thing with the fake locking hubs and the little switch on the dash (I'd love to convert it to a manual shifter...?). 174k on chassis, so things need to be done, 40k on engine, 3k on BTS 4r100.
Yesterday I was running around town, made a stop, and when I started moving again got a loud grinding from the front axle. Thought maybe I'd picked up a rock in a caliper or something, so I jumped out and checked everything, no joy. Moved forward, there it is again. No vibration, but loud enough (or telegraphing enough) to hear clearly in the cab. Let the truck roll forward, popped in to neutral, noise fades away. Back in to drive, there it is. So, now I know it's trans/t-case/driveshaft/related. I recently put new vacuum lines in, checked all the connections, and pulled, cleaned and lubed the hubs.
And since the trans is a nearly new BTS that is working just find, I'm narrowing the search to the hubs, drive shaft, t-case.
Get home (noise abates above 30mph, or everything else drowns it out), crawl under, and find the front driveshaft is locked. Ok, stuck hub? Pull out both the fake locking hubs, and now the shaft turns. I can turn each front axle by hand at the u-joint, and I kinda hear a faint grinding on the right side (will bad needles make noise only under a load from the trans and not coasting in neutral?), and when I swing the drive shaft around the left axle moves, right doesn't, etc etc.
I'm going to pull the drive shaft today and check the U joints, and drive a bit to see if the noise is still there, but I am thinking I might have some bad needles on the pax side axle...
View 4 Replies
I went out getting firewood in my 2001 F350 4X4 6.8l V10 auto . Backed up to the slash pile, put the truck in 4X4 Low and went to work.
When we finished I flipped the switch to 2WD, but the transfer case would not dis-engage and the IDIOT LIGHT on the dashboard stays on 4X4 Low... I can't get the truck out of 4X4 Low. I turned the hubs from auto to lockand its still stuck in low range.
View 8 Replies
